diff --git linux-libre-5.4.168-gnu1/Documentation/admin-guide/kernel-parameters.txt linux-libre-5.4.169-gnu1/Documentation/admin-guide/kernel-parameters.txt
index b11e1fd95ee5..e7f71df9daf1 100644
--- linux-libre-5.4.168-gnu1/Documentation/admin-guide/kernel-parameters.txt
+++ linux-libre-5.4.169-gnu1/Documentation/admin-guide/kernel-parameters.txt
@@ -2112,8 +2112,12 @@
 			Default is 1 (enabled)
 
 	kvm-intel.emulate_invalid_guest_state=
-			[KVM,Intel] Enable emulation of invalid guest states
-			Default is 0 (disabled)
+			[KVM,Intel] Disable emulation of invalid guest state.
+			Ignored if kvm-intel.enable_unrestricted_guest=1, as
+			guest state is never invalid for unrestricted guests.
+			This param doesn't apply to nested guests (L2), as KVM
+			never emulates invalid L2 guest state.
+			Default is 1 (enabled)
 
 	kvm-intel.flexpriority=
 			[KVM,Intel] Disable FlexPriority feature (TPR shadow).
diff --git linux-libre-5.4.168-gnu1/Documentation/hwmon/lm90.rst linux-libre-5.4.169-gnu1/Documentation/hwmon/lm90.rst
index 953315987c06..03851cbe637c 100644
--- linux-libre-5.4.168-gnu1/Documentation/hwmon/lm90.rst
+++ linux-libre-5.4.169-gnu1/Documentation/hwmon/lm90.rst
@@ -123,6 +123,18 @@ Supported chips:
 
 	       http://www.maxim-ic.com/quick_view2.cfm/qv_pk/3497
 
+  * Maxim MAX6654
+
+    Prefix: 'max6654'
+
+    Addresses scanned: I2C 0x18, 0x19, 0x1a, 0x29, 0x2a, 0x2b,
+
+			   0x4c, 0x4d and 0x4e
+
+    Datasheet: Publicly available at the Maxim website
+
+	       https://www.maximintegrated.com/en/products/sensors/MAX6654.html
+
   * Maxim MAX6657
 
     Prefix: 'max6657'
@@ -253,6 +265,16 @@ Supported chips:
 
 	       http://www.ti.com/litv/pdf/sbos686
 
+  * Texas Instruments TMP461
+
+    Prefix: 'tmp461'
+
+    Addresses scanned: I2C 0x48 through 0x4F
+
+    Datasheet: Publicly available at TI website
+
+	       https://www.ti.com/lit/gpn/tmp461
+
 Author: Jean Delvare <jdelvare@suse.de>
 
 
@@ -301,6 +323,13 @@ ADT7461, ADT7461A, NCT1008:
   * Extended temperature range (breaks compatibility)
   * Lower resolution for remote temperature
 
+MAX6654:
+  * Better local resolution
+  * Selectable address
+  * Remote sensor type selection
+  * Extended temperature range
+  * Extended resolution only available when conversion rate <= 1 Hz
+
 MAX6657 and MAX6658:
   * Better local resolution
   * Remote sensor type selection
@@ -336,8 +365,8 @@ SA56004X:
 
 All temperature values are given in degrees Celsius. Resolution
 is 1.0 degree for the local temperature, 0.125 degree for the remote
-temperature, except for the MAX6657, MAX6658 and MAX6659 which have a
-resolution of 0.125 degree for both temperatures.
+temperature, except for the MAX6654, MAX6657, MAX6658 and MAX6659 which have
+a resolution of 0.125 degree for both temperatures.
 
 Each sensor has its own high and low limits, plus a critical limit.
 Additionally, there is a relative hysteresis value common to both critical
diff --git linux-libre-5.4.168-gnu1/Documentation/networking/bonding.txt linux-libre-5.4.169-gnu1/Documentation/networking/bonding.txt
index e3abfbd32f71..b020e6ce6dd4 100644
--- linux-libre-5.4.168-gnu1/Documentation/networking/bonding.txt
+++ linux-libre-5.4.169-gnu1/Documentation/networking/bonding.txt
@@ -191,11 +191,12 @@ ad_actor_sys_prio
 ad_actor_system
 
 	In an AD system, this specifies the mac-address for the actor in
-	protocol packet exchanges (LACPDUs). The value cannot be NULL or
-	multicast. It is preferred to have the local-admin bit set for this
-	mac but driver does not enforce it. If the value is not given then
-	system defaults to using the masters' mac address as actors' system
-	address.
+	protocol packet exchanges (LACPDUs). The value cannot be a multicast
+	address. If the all-zeroes MAC is specified, bonding will internally
+	use the MAC of the bond itself. It is preferred to have the
+	local-admin bit set for this mac but driver does not enforce it. If
+	the value is not given then system defaults to using the masters'
+	mac address as actors' system address.
 
 	This parameter has effect only in 802.3ad mode and is available through
 	SysFs interface.
diff --git linux-libre-5.4.168-gnu1/Makefile linux-libre-5.4.169-gnu1/Makefile
index 61825633fbb7..57288363dd45 100644
--- linux-libre-5.4.168-gnu1/Makefile
+++ linux-libre-5.4.169-gnu1/Makefile
@@ -1,7 +1,7 @@
 # SPDX-License-Identifier: GPL-2.0
 VERSION = 5
 PATCHLEVEL = 4
-SUBLEVEL = 168
+SUBLEVEL = 169
 EXTRAVERSION = -gnu1
 NAME = Kleptomaniac Octopus
 
diff --git linux-libre-5.4.168-gnu1/arch/arm/kernel/entry-armv.S linux-libre-5.4.169-gnu1/arch/arm/kernel/entry-armv.S
index b62d74a2c73a..4937d514318e 100644
--- linux-libre-5.4.168-gnu1/arch/arm/kernel/entry-armv.S
+++ linux-libre-5.4.169-gnu1/arch/arm/kernel/entry-armv.S
@@ -596,11 +596,9 @@ call_fpe:
 	tstne	r0, #0x04000000			@ bit 26 set on both ARM and Thumb-2
 	reteq	lr
 	and	r8, r0, #0x00000f00		@ mask out CP number
- THUMB(	lsr	r8, r8, #8		)
 	mov	r7, #1
-	add	r6, r10, #TI_USED_CP
- ARM(	strb	r7, [r6, r8, lsr #8]	)	@ set appropriate used_cp[]
- THUMB(	strb	r7, [r6, r8]		)	@ set appropriate used_cp[]
+	add	r6, r10, r8, lsr #8		@ add used_cp[] array offset first
+	strb	r7, [r6, #TI_USED_CP]		@ set appropriate used_cp[]
 #ifdef CONFIG_IWMMXT
 	@ Test if we need to give access to iWMMXt coprocessors
 	ldr	r5, [r10, #TI_FLAGS]
@@ -609,7 +607,7 @@ call_fpe:
 	bcs	iwmmxt_task_enable
 #endif
  ARM(	add	pc, pc, r8, lsr #6	)
- THUMB(	lsl	r8, r8, #2		)
+ THUMB(	lsr	r8, r8, #6		)
  THUMB(	add	pc, r8			)
 	nop
 
diff --git linux-libre-5.4.168-gnu1/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-zero-plus.dts linux-libre-5.4.169-gnu1/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-zero-plus.dts
index db6ea7b58999..19f930f43936 100644
--- linux-libre-5.4.168-gnu1/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-zero-plus.dts
+++ linux-libre-5.4.169-gnu1/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-zero-plus.dts
@@ -72,7 +72,7 @@
 	pinctrl-0 = <&emac_rgmii_pins>;
 	phy-supply = <&reg_gmac_3v3>;
 	phy-handle = <&ext_rgmii_phy>;
-	phy-mode = "rgmii";
+	phy-mode = "rgmii-id";
 	status = "okay";
 };
 
diff --git linux-libre-5.4.168-gnu1/arch/parisc/kernel/syscall.S linux-libre-5.4.169-gnu1/arch/parisc/kernel/syscall.S
index a37814cb66c7..8b616aada649 100644
--- linux-libre-5.4.168-gnu1/arch/parisc/kernel/syscall.S
+++ linux-libre-5.4.169-gnu1/arch/parisc/kernel/syscall.S
@@ -478,7 +478,7 @@ lws_start:
 	extrd,u	%r1,PSW_W_BIT,1,%r1
 	/* sp must be aligned on 4, so deposit the W bit setting into
 	 * the bottom of sp temporarily */
-	or,ev	%r1,%r30,%r30
+	or,od	%r1,%r30,%r30
 
 	/* Clip LWS number to a 32-bit value for 32-bit processes */
 	depdi	0, 31, 32, %r20
diff --git linux-libre-5.4.168-gnu1/arch/x86/include/asm/pgtable.h linux-libre-5.4.169-gnu1/arch/x86/include/asm/pgtable.h
index ea85f23d9e22..1ae7c20f5469 100644
--- linux-libre-5.4.168-gnu1/arch/x86/include/asm/pgtable.h
+++ linux-libre-5.4.169-gnu1/arch/x86/include/asm/pgtable.h
@@ -1375,8 +1375,8 @@ static inline pmd_t pmd_swp_clear_soft_dirty(pmd_t pmd)
 #endif
 #endif
 
-#define PKRU_AD_BIT 0x1
-#define PKRU_WD_BIT 0x2
+#define PKRU_AD_BIT 0x1u
+#define PKRU_WD_BIT 0x2u
 #define PKRU_BITS_PER_PKEY 2
 
 #ifdef CONFIG_X86_INTEL_MEMORY_PROTECTION_KEYS
diff --git linux-libre-5.4.168-gnu1/drivers/char/ipmi/ipmi_msghandler.c linux-libre-5.4.169-gnu1/drivers/char/ipmi/ipmi_msghandler.c
index 8a93d5a494ff..ad2e6d55d4a5 100644
--- linux-libre-5.4.168-gnu1/drivers/char/ipmi/ipmi_msghandler.c
+++ linux-libre-5.4.169-gnu1/drivers/char/ipmi/ipmi_msghandler.c
@@ -2938,7 +2938,7 @@ cleanup_bmc_device(struct kref *ref)
 	 * with removing the device attributes while reading a device
 	 * attribute.
 	 */
-	schedule_work(&bmc->remove_work);
+	queue_work(remove_work_wq, &bmc->remove_work);
 }
 
 /*
@@ -5156,22 +5156,27 @@ static int ipmi_init_msghandler(void)
 	if (initialized)
 		goto out;
 
-	init_srcu_struct(&ipmi_interfaces_srcu);
-
-	timer_setup(&ipmi_timer, ipmi_timeout, 0);
-	mod_timer(&ipmi_timer, jiffies + IPMI_TIMEOUT_JIFFIES);
-
-	atomic_notifier_chain_register(&panic_notifier_list, &panic_block);
+	rv = init_srcu_struct(&ipmi_interfaces_srcu);
+	if (rv)
+		goto out;
 
 	remove_work_wq = create_singlethread_workqueue("ipmi-msghandler-remove-wq");
 	if (!remove_work_wq) {
 		pr_err("unable to create ipmi-msghandler-remove-wq workqueue");
 		rv = -ENOMEM;
-		goto out;
+		goto out_wq;
 	}
 
+	timer_setup(&ipmi_timer, ipmi_timeout, 0);
+	mod_timer(&ipmi_timer, jiffies + IPMI_TIMEOUT_JIFFIES);
+
+	atomic_notifier_chain_register(&panic_notifier_list, &panic_block);
+
 	initialized = true;
 
+out_wq:
+	if (rv)
+		cleanup_srcu_struct(&ipmi_interfaces_srcu);
 out:
 	mutex_unlock(&ipmi_interfaces_mutex);
 	return rv;
diff --git linux-libre-5.4.168-gnu1/drivers/char/ipmi/ipmi_ssif.c linux-libre-5.4.169-gnu1/drivers/char/ipmi/ipmi_ssif.c
index 8ac390c2b514..bb42a1c92cae 100644
--- linux-libre-5.4.168-gnu1/drivers/char/ipmi/ipmi_ssif.c
+++ linux-libre-5.4.169-gnu1/drivers/char/ipmi/ipmi_ssif.c
@@ -1704,6 +1704,9 @@ static int ssif_probe(struct i2c_client *client, const struct i2c_device_id *id)
 		}
 	}
 
+	ssif_info->client = client;
+	i2c_set_clientdata(client, ssif_info);
+
 	rv = ssif_check_and_remove(client, ssif_info);
 	/* If rv is 0 and addr source is not SI_ACPI, continue probing */
 	if (!rv && ssif_info->addr_source == SI_ACPI) {
@@ -1724,9 +1727,6 @@ static int ssif_probe(struct i2c_client *client, const struct i2c_device_id *id)
 		ipmi_addr_src_to_str(ssif_info->addr_source),
 		client->addr, client->adapter->name, slave_addr);
 
-	ssif_info->client = client;
-	i2c_set_clientdata(client, ssif_info);
-
 	/* Now check for system interface capabilities */
 	msg[0] = IPMI_NETFN_APP_REQUEST << 2;
 	msg[1] = IPMI_GET_SYSTEM_INTERFACE_CAPABILITIES_CMD;
@@ -1926,6 +1926,7 @@ static int ssif_probe(struct i2c_client *client, const struct i2c_device_id *id)
 
 		dev_err(&ssif_info->client->dev,
 			"Unable to start IPMI SSIF: %d\n", rv);
+		i2c_set_clientdata(client, NULL);
 		kfree(ssif_info);
 	}
 	kfree(resp);
diff --git linux-libre-5.4.168-gnu1/drivers/hid/hid-holtek-mouse.c linux-libre-5.4.169-gnu1/drivers/hid/hid-holtek-mouse.c
index b7172c48ef9f..7c907939bfae 100644
--- linux-libre-5.4.168-gnu1/drivers/hid/hid-holtek-mouse.c
+++ linux-libre-5.4.169-gnu1/drivers/hid/hid-holtek-mouse.c
@@ -65,8 +65,23 @@ static __u8 *holtek_mouse_report_fixup(struct hid_device *hdev, __u8 *rdesc,
 static int holtek_mouse_probe(struct hid_device *hdev,
 			      const struct hid_device_id *id)
 {
+	int ret;
+
 	if (!hid_is_usb(hdev))
 		return -EINVAL;
+
+	ret = hid_parse(hdev);
+	if (ret) {
+		hid_err(hdev, "hid parse failed: %d\n", ret);
+		return ret;
+	}
+
+	ret = hid_hw_start(hdev, HID_CONNECT_DEFAULT);
+	if (ret) {
+		hid_err(hdev, "hw start failed: %d\n", ret);
+		return ret;
+	}
+
 	return 0;
 }
 
diff --git linux-libre-5.4.168-gnu1/drivers/hwmon/Kconfig linux-libre-5.4.169-gnu1/drivers/hwmon/Kconfig
index 13a6b4afb4b3..049563d503b6 100644
--- linux-libre-5.4.168-gnu1/drivers/hwmon/Kconfig
+++ linux-libre-5.4.169-gnu1/drivers/hwmon/Kconfig
@@ -1132,10 +1132,11 @@ config SENSORS_LM90
 	help
 	  If you say yes here you get support for National Semiconductor LM90,
 	  LM86, LM89 and LM99, Analog Devices ADM1032, ADT7461, and ADT7461A,
-	  Maxim MAX6646, MAX6647, MAX6648, MAX6649, MAX6657, MAX6658, MAX6659,
-	  MAX6680, MAX6681, MAX6692, MAX6695, MAX6696, ON Semiconductor NCT1008,
-	  Winbond/Nuvoton W83L771W/G/AWG/ASG, Philips SA56004, GMT G781, and
-	  Texas Instruments TMP451 sensor chips.
+	  Maxim MAX6646, MAX6647, MAX6648, MAX6649, MAX6654, MAX6657, MAX6658,
+	  MAX6659, MAX6680, MAX6681, MAX6692, MAX6695, MAX6696,
+	  ON Semiconductor NCT1008, Winbond/Nuvoton W83L771W/G/AWG/ASG,
+	  Philips SA56004, GMT G781, Texas Instruments TMP451 and TMP461
+	  sensor chips.
 
 	  This driver can also be built as a module. If so, the module
 	  will be called lm90.
diff --git linux-libre-5.4.168-gnu1/drivers/hwmon/lm90.c linux-libre-5.4.169-gnu1/drivers/hwmon/lm90.c
index 9b3c9f390ef8..9abb4507f572 100644
--- linux-libre-5.4.168-gnu1/drivers/hwmon/lm90.c
+++ linux-libre-5.4.169-gnu1/drivers/hwmon/lm90.c
@@ -35,6 +35,15 @@
  * explicitly as max6659, or if its address is not 0x4c.
  * These chips lack the remote temperature offset feature.
  *
+ * This driver also supports the MAX6654 chip made by Maxim. This chip can be
+ * at 9 different addresses, similar to MAX6680/MAX6681. The MAX6654 is similar
+ * to MAX6657/MAX6658/MAX6659, but does not support critical temperature
+ * limits. Extended range is available by setting the configuration register
+ * accordingly, and is done during initialization. Extended precision is only
+ * available at conversion rates of 1 Hz and slower. Note that extended
+ * precision is not enabled by default, as this driver initializes all chips
+ * to 2 Hz by design.
+ *
  * This driver also supports the MAX6646, MAX6647, MAX6648, MAX6649 and
  * MAX6692 chips made by Maxim.  These are again similar to the LM86,
  * but they use unsigned temperature values and can report temperatures
@@ -61,10 +70,10 @@
  * This driver also supports the G781 from GMT. This device is compatible
  * with the ADM1032.
  *
- * This driver also supports TMP451 from Texas Instruments. This device is
- * supported in both compatibility and extended mode. It's mostly compatible
- * with ADT7461 except for local temperature low byte register and max
- * conversion rate.
+ * This driver also supports TMP451 and TMP461 from Texas Instruments.
+ * Those devices are supported in both compatibility and extended mode.
+ * They are mostly compatible with ADT7461 except for local temperature
+ * low byte register and max conversion rate.
  *
  * Since the LM90 was the first chipset supported by this driver, most
  * comments will refer to this chipset, but are actually general and
@@ -94,8 +103,8 @@
  * have address 0x4d.
  * MAX6647 has address 0x4e.
  * MAX6659 can have address 0x4c, 0x4d or 0x4e.
- * MAX6680 and MAX6681 can have address 0x18, 0x19, 0x1a, 0x29, 0x2a, 0x2b,
- * 0x4c, 0x4d or 0x4e.
+ * MAX6654, MAX6680, and MAX6681 can have address 0x18, 0x19, 0x1a, 0x29,
+ * 0x2a, 0x2b, 0x4c, 0x4d or 0x4e.
  * SA56004 can have address 0x48 through 0x4F.
  */
 
@@ -104,7 +113,7 @@ static const unsigned short normal_i2c[] = {
 	0x4d, 0x4e, 0x4f, I2C_CLIENT_END };
 
 enum chips { lm90, adm1032, lm99, lm86, max6657, max6659, adt7461, max6680,
-	max6646, w83l771, max6696, sa56004, g781, tmp451 };
+	max6646, w83l771, max6696, sa56004, g781, tmp451, tmp461, max6654 };
 
 /*
  * The LM90 registers
@@ -145,7 +154,7 @@ enum chips { lm90, adm1032, lm99, lm86, max6657, max6659, adt7461, max6680,
 #define LM90_REG_R_TCRIT_HYST		0x21
 #define LM90_REG_W_TCRIT_HYST		0x21
 
-/* MAX6646/6647/6649/6657/6658/6659/6695/6696 registers */
+/* MAX6646/6647/6649/6654/6657/6658/6659/6695/6696 registers */
 
 #define MAX6657_REG_R_LOCAL_TEMPL	0x11
 #define MAX6696_REG_R_STATUS2		0x12
@@ -160,8 +169,12 @@ enum chips { lm90, adm1032, lm99, lm86, max6657, max6659, adt7461, max6680,
 
 #define LM90_MAX_CONVRATE_MS	16000	/* Maximum conversion rate in ms */
 
-/* TMP451 registers */
+/* TMP451/TMP461 registers */
 #define TMP451_REG_R_LOCAL_TEMPL	0x15
+#define TMP451_REG_CONALERT		0x22
+
+#define TMP461_REG_CHEN			0x16
+#define TMP461_REG_DFC			0x24
 
 /*
  * Device flags
@@ -174,7 +187,10 @@ enum chips { lm90, adm1032, lm99, lm86, max6657, max6659, adt7461, max6680,
 #define LM90_HAVE_EMERGENCY_ALARM (1 << 5)/* emergency alarm		*/
 #define LM90_HAVE_TEMP3		(1 << 6) /* 3rd temperature sensor	*/
 #define LM90_HAVE_BROKEN_ALERT	(1 << 7) /* Broken alert		*/
-#define LM90_PAUSE_FOR_CONFIG	(1 << 8) /* Pause conversion for config	*/
+#define LM90_HAVE_EXTENDED_TEMP	(1 << 8) /* extended temperature support*/
+#define LM90_PAUSE_FOR_CONFIG	(1 << 9) /* Pause conversion for config	*/
+#define LM90_HAVE_CRIT		(1 << 10)/* Chip supports CRIT/OVERT register	*/
+#define LM90_HAVE_CRIT_ALRM_SWP	(1 << 11)/* critical alarm bits swapped	*/
 
 /* LM90 status */
 #define LM90_STATUS_LTHRM	(1 << 0) /* local THERM limit tripped */
@@ -184,6 +200,7 @@ enum chips { lm90, adm1032, lm99, lm86, max6657, max6659, adt7461, max6680,
 #define LM90_STATUS_RHIGH	(1 << 4) /* remote high temp limit tripped */
 #define LM90_STATUS_LLOW	(1 << 5) /* local low temp limit tripped */
 #define LM90_STATUS_LHIGH	(1 << 6) /* local high temp limit tripped */
+#define LM90_STATUS_BUSY	(1 << 7) /* conversion is ongoing */
 
 #define MAX6696_STATUS2_R2THRM	(1 << 1) /* remote2 THERM limit tripped */
 #define MAX6696_STATUS2_R2OPEN	(1 << 2) /* remote2 is an open circuit */
@@ -209,6 +226,7 @@ static const struct i2c_device_id lm90_id[] = {
 	{ "max6646", max6646 },
 	{ "max6647", max6646 },
 	{ "max6649", max6646 },
+	{ "max6654", max6654 },
 	{ "max6657", max6657 },
 	{ "max6658", max6657 },
 	{ "max6659", max6659 },
@@ -220,6 +238,7 @@ static const struct i2c_device_id lm90_id[] = {
 	{ "w83l771", w83l771 },
 	{ "sa56004", sa56004 },
 	{ "tmp451", tmp451 },
+	{ "tmp461", tmp461 },
 	{ }
 };
 MODULE_DEVICE_TABLE(i2c, lm90_id);
@@ -269,6 +288,10 @@ static const struct of_device_id __maybe_unused lm90_of_match[] = {
 		.compatible = "dallas,max6649",
 		.data = (void *)max6646
 	},
+	{
+		.compatible = "dallas,max6654",
+		.data = (void *)max6654
+	},
 	{
 		.compatible = "dallas,max6657",
 		.data = (void *)max6657
@@ -313,6 +336,10 @@ static const struct of_device_id __maybe_unused lm90_of_match[] = {
 		.compatible = "ti,tmp451",
 		.data = (void *)tmp451
 	},
+	{
+		.compatible = "ti,tmp461",
+		.data = (void *)tmp461
+	},
 	{ },
 };
 MODULE_DEVICE_TABLE(of, lm90_of_match);
@@ -331,80 +358,98 @@ struct lm90_params {
 static const struct lm90_params lm90_params[] = {
 	[adm1032] = {
 		.flags = LM90_HAVE_OFFSET | LM90_HAVE_REM_LIMIT_EXT
-		  | LM90_HAVE_BROKEN_ALERT,
+		  | LM90_HAVE_BROKEN_ALERT | LM90_HAVE_CRIT,
 		.alert_alarms = 0x7c,
 		.max_convrate = 10,
 	},
 	[adt7461] = {
 		.flags = LM90_HAVE_OFFSET | LM90_HAVE_REM_LIMIT_EXT
-		  | LM90_HAVE_BROKEN_ALERT,
+		  | LM90_HAVE_BROKEN_ALERT | LM90_HAVE_EXTENDED_TEMP
+		  | LM90_HAVE_CRIT,
 		.alert_alarms = 0x7c,
 		.max_convrate = 10,
 	},
 	[g781] = {
 		.flags = LM90_HAVE_OFFSET | LM90_HAVE_REM_LIMIT_EXT
-		  | LM90_HAVE_BROKEN_ALERT,
+		  | LM90_HAVE_BROKEN_ALERT | LM90_HAVE_CRIT,
 		.alert_alarms = 0x7c,
 		.max_convrate = 8,
 	},
 	[lm86] = {
-		.flags = LM90_HAVE_OFFSET | LM90_HAVE_REM_LIMIT_EXT,
+		.flags = LM90_HAVE_OFFSET | LM90_HAVE_REM_LIMIT_EXT
+		  | LM90_HAVE_CRIT,
 		.alert_alarms = 0x7b,
 		.max_convrate = 9,
 	},
 	[lm90] = {
-		.flags = LM90_HAVE_OFFSET | LM90_HAVE_REM_LIMIT_EXT,
+		.flags = LM90_HAVE_OFFSET | LM90_HAVE_REM_LIMIT_EXT
+		  | LM90_HAVE_CRIT,
 		.alert_alarms = 0x7b,
 		.max_convrate = 9,
 	},
 	[lm99] = {
-		.flags = LM90_HAVE_OFFSET | LM90_HAVE_REM_LIMIT_EXT,
+		.flags = LM90_HAVE_OFFSET | LM90_HAVE_REM_LIMIT_EXT
+		  | LM90_HAVE_CRIT,
 		.alert_alarms = 0x7b,
 		.max_convrate = 9,
 	},
 	[max6646] = {
+		.flags = LM90_HAVE_CRIT,
 		.alert_alarms = 0x7c,
 		.max_convrate = 6,
 		.reg_local_ext = MAX6657_REG_R_LOCAL_TEMPL,
 	},
+	[max6654] = {
+		.alert_alarms = 0x7c,
+		.max_convrate = 7,
+		.reg_local_ext = MAX6657_REG_R_LOCAL_TEMPL,
+	},
 	[max6657] = {
-		.flags = LM90_PAUSE_FOR_CONFIG,
+		.flags = LM90_PAUSE_FOR_CONFIG | LM90_HAVE_CRIT,
 		.alert_alarms = 0x7c,
 		.max_convrate = 8,
 		.reg_local_ext = MAX6657_REG_R_LOCAL_TEMPL,
 	},
 	[max6659] = {
-		.flags = LM90_HAVE_EMERGENCY,
+		.flags = LM90_HAVE_EMERGENCY | LM90_HAVE_CRIT,
 		.alert_alarms = 0x7c,
 		.max_convrate = 8,
 		.reg_local_ext = MAX6657_REG_R_LOCAL_TEMPL,
 	},
 	[max6680] = {
-		.flags = LM90_HAVE_OFFSET,
+		.flags = LM90_HAVE_OFFSET | LM90_HAVE_CRIT
+		  | LM90_HAVE_CRIT_ALRM_SWP,
 		.alert_alarms = 0x7c,
 		.max_convrate = 7,
 	},
 	[max6696] = {
 		.flags = LM90_HAVE_EMERGENCY
-		  | LM90_HAVE_EMERGENCY_ALARM | LM90_HAVE_TEMP3,
+		  | LM90_HAVE_EMERGENCY_ALARM | LM90_HAVE_TEMP3 | LM90_HAVE_CRIT,
 		.alert_alarms = 0x1c7c,
 		.max_convrate = 6,
 		.reg_local_ext = MAX6657_REG_R_LOCAL_TEMPL,
 	},
 	[w83l771] = {
-		.flags = LM90_HAVE_OFFSET | LM90_HAVE_REM_LIMIT_EXT,
+		.flags = LM90_HAVE_OFFSET | LM90_HAVE_REM_LIMIT_EXT | LM90_HAVE_CRIT,
 		.alert_alarms = 0x7c,
 		.max_convrate = 8,
 	},
 	[sa56004] = {
-		.flags = LM90_HAVE_OFFSET | LM90_HAVE_REM_LIMIT_EXT,
+		.flags = LM90_HAVE_OFFSET | LM90_HAVE_REM_LIMIT_EXT | LM90_HAVE_CRIT,
 		.alert_alarms = 0x7b,
 		.max_convrate = 9,
 		.reg_local_ext = SA56004_REG_R_LOCAL_TEMPL,
 	},
 	[tmp451] = {
 		.flags = LM90_HAVE_OFFSET | LM90_HAVE_REM_LIMIT_EXT
-		  | LM90_HAVE_BROKEN_ALERT,
+		  | LM90_HAVE_BROKEN_ALERT | LM90_HAVE_EXTENDED_TEMP | LM90_HAVE_CRIT,
+		.alert_alarms = 0x7c,
+		.max_convrate = 9,
+		.reg_local_ext = TMP451_REG_R_LOCAL_TEMPL,
+	},
+	[tmp461] = {
+		.flags = LM90_HAVE_OFFSET | LM90_HAVE_REM_LIMIT_EXT
+		  | LM90_HAVE_BROKEN_ALERT | LM90_HAVE_EXTENDED_TEMP | LM90_HAVE_CRIT,
 		.alert_alarms = 0x7c,
 		.max_convrate = 9,
 		.reg_local_ext = TMP451_REG_R_LOCAL_TEMPL,
@@ -632,20 +677,22 @@ static int lm90_update_limits(struct device *dev)
 	struct i2c_client *client = data->client;
 	int val;
 
-	val = lm90_read_reg(client, LM90_REG_R_LOCAL_CRIT);
-	if (val < 0)
-		return val;
-	data->temp8[LOCAL_CRIT] = val;
+	if (data->flags & LM90_HAVE_CRIT) {
+		val = lm90_read_reg(client, LM90_REG_R_LOCAL_CRIT);
+		if (val < 0)
+			return val;
+		data->temp8[LOCAL_CRIT] = val;
 
-	val = lm90_read_reg(client, LM90_REG_R_REMOTE_CRIT);
-	if (val < 0)
-		return val;
-	data->temp8[REMOTE_CRIT] = val;
+		val = lm90_read_reg(client, LM90_REG_R_REMOTE_CRIT);
+		if (val < 0)
+			return val;
+		data->temp8[REMOTE_CRIT] = val;
 
-	val = lm90_read_reg(client, LM90_REG_R_TCRIT_HYST);
-	if (val < 0)
-		return val;
-	data->temp_hyst = val;
+		val = lm90_read_reg(client, LM90_REG_R_TCRIT_HYST);
+		if (val < 0)
+			return val;
+		data->temp_hyst = val;
+	}
 
 	val = lm90_read_reg(client, LM90_REG_R_REMOTE_LOWH);
 	if (val < 0)
@@ -773,7 +820,7 @@ static int lm90_update_device(struct device *dev)
 		val = lm90_read_reg(client, LM90_REG_R_STATUS);
 		if (val < 0)
 			return val;
-		data->alarms = val;	/* lower 8 bit of alarms */
+		data->alarms = val & ~LM90_STATUS_BUSY;
 
 		if (data->kind == max6696) {
 			val = lm90_select_remote_channel(data, 1);
@@ -979,7 +1026,7 @@ static int lm90_get_temp11(struct lm90_data *data, int index)
 	s16 temp11 = data->temp11[index];
 	int temp;
 
-	if (data->kind == adt7461 || data->kind == tmp451)
+	if (data->flags & LM90_HAVE_EXTENDED_TEMP)
 		temp = temp_from_u16_adt7461(data, temp11);
 	else if (data->kind == max6646)
 		temp = temp_from_u16(temp11);
@@ -1013,7 +1060,7 @@ static int lm90_set_temp11(struct lm90_data *data, int index, long val)
 	if (data->kind == lm99 && index <= 2)
 		val -= 16000;
 
-	if (data->kind == adt7461 || data->kind == tmp451)
+	if (data->flags & LM90_HAVE_EXTENDED_TEMP)
 		data->temp11[index] = temp_to_u16_adt7461(data, val);
 	else if (data->kind == max6646)
 		data->temp11[index] = temp_to_u8(val) << 8;
@@ -1040,7 +1087,7 @@ static int lm90_get_temp8(struct lm90_data *data, int index)
 	s8 temp8 = data->temp8[index];
 	int temp;
 
-	if (data->kind == adt7461 || data->kind == tmp451)
+	if (data->flags & LM90_HAVE_EXTENDED_TEMP)
 		temp = temp_from_u8_adt7461(data, temp8);
 	else if (data->kind == max6646)
 		temp = temp_from_u8(temp8);
@@ -1073,7 +1120,7 @@ static int lm90_set_temp8(struct lm90_data *data, int index, long val)
 	if (data->kind == lm99 && index == 3)
 		val -= 16000;
 
-	if (data->kind == adt7461 || data->kind == tmp451)
+	if (data->flags & LM90_HAVE_EXTENDED_TEMP)
 		data->temp8[index] = temp_to_u8_adt7461(data, val);
 	else if (data->kind == max6646)
 		data->temp8[index] = temp_to_u8(val);
@@ -1091,7 +1138,7 @@ static int lm90_get_temphyst(struct lm90_data *data, int index)
 {
 	int temp;
 
-	if (data->kind == adt7461 || data->kind == tmp451)
+	if (data->flags & LM90_HAVE_EXTENDED_TEMP)
 		temp = temp_from_u8_adt7461(data, data->temp8[index]);
 	else if (data->kind == max6646)
 		temp = temp_from_u8(data->temp8[index]);
@@ -1111,7 +1158,7 @@ static int lm90_set_temphyst(struct lm90_data *data, long val)
 	int temp;
 	int err;
 
-	if (data->kind == adt7461 || data->kind == tmp451)
+	if (data->flags & LM90_HAVE_EXTENDED_TEMP)
 		temp = temp_from_u8_adt7461(data, data->temp8[LOCAL_CRIT]);
 	else if (data->kind == max6646)
 		temp = temp_from_u8(data->temp8[LOCAL_CRIT]);
@@ -1147,6 +1194,7 @@ static const u8 lm90_temp_emerg_index[3] = {
 static const u8 lm90_min_alarm_bits[3] = { 5, 3, 11 };
 static const u8 lm90_max_alarm_bits[3] = { 6, 4, 12 };
 static const u8 lm90_crit_alarm_bits[3] = { 0, 1, 9 };
+static const u8 lm90_crit_alarm_bits_swapped[3] = { 1, 0, 9 };
 static const u8 lm90_emergency_alarm_bits[3] = { 15, 13, 14 };
 static const u8 lm90_fault_bits[3] = { 0, 2, 10 };
 
@@ -1172,7 +1220,10 @@ static int lm90_temp_read(struct device *dev, u32 attr, int channel, long *val)
 		*val = (data->alarms >> lm90_max_alarm_bits[channel]) & 1;
 		break;
 	case hwmon_temp_crit_alarm:
-		*val = (data->alarms >> lm90_crit_alarm_bits[channel]) & 1;
+		if (data->flags & LM90_HAVE_CRIT_ALRM_SWP)
+			*val = (data->alarms >> lm90_crit_alarm_bits_swapped[channel]) & 1;
+		else
+			*val = (data->alarms >> lm90_crit_alarm_bits[channel]) & 1;
 		break;
 	case hwmon_temp_emergency_alarm:
 		*val = (data->alarms >> lm90_emergency_alarm_bits[channel]) & 1;
@@ -1420,12 +1471,11 @@ static int lm90_detect(struct i2c_client *client,
 	if (man_id < 0 || chip_id < 0 || config1 < 0 || convrate < 0)
 		return -ENODEV;
 
-	if (man_id == 0x01 || man_id == 0x5C || man_id == 0x41) {
+	if (man_id == 0x01 || man_id == 0x5C || man_id == 0xA1) {
 		config2 = i2c_smbus_read_byte_data(client, LM90_REG_R_CONFIG2);
 		if (config2 < 0)
 			return -ENODEV;
-	} else
-		config2 = 0;		/* Make compiler happy */
+	}
 
 	if ((address == 0x4C || address == 0x4D)
 	 && man_id == 0x01) { /* National Semiconductor */
@@ -1557,6 +1607,16 @@ static int lm90_detect(struct i2c_client *client,
 		 && (config1 & 0x3f) == 0x00
 		 && convrate <= 0x07) {
 			name = "max6646";
+		} else
+		/*
+		 * The chip_id of the MAX6654 holds the revision of the chip.
+		 * The lowest 3 bits of the config1 register are unused and
+		 * should return zero when read.
+		 */
+		if (chip_id == 0x08
+		 && (config1 & 0x07) == 0x00
+		 && convrate <= 0x07) {
+			name = "max6654";
 		}
 	} else
 	if (address == 0x4C
@@ -1589,18 +1649,26 @@ static int lm90_detect(struct i2c_client *client,
 		 && convrate <= 0x08)
 			name = "g781";
 	} else
-	if (address == 0x4C
-	 && man_id == 0x55) { /* Texas Instruments */
-		int local_ext;
+	if (man_id == 0x55 && chip_id == 0x00 &&
+	    (config1 & 0x1B) == 0x00 && convrate <= 0x09) {
+		int local_ext, conalert, chen, dfc;
 
 		local_ext = i2c_smbus_read_byte_data(client,
 						     TMP451_REG_R_LOCAL_TEMPL);
-
-		if (chip_id == 0x00 /* TMP451 */
-		 && (config1 & 0x1B) == 0x00
-		 && convrate <= 0x09
-		 && (local_ext & 0x0F) == 0x00)
-			name = "tmp451";
+		conalert = i2c_smbus_read_byte_data(client,
+						    TMP451_REG_CONALERT);
+		chen = i2c_smbus_read_byte_data(client, TMP461_REG_CHEN);
+		dfc = i2c_smbus_read_byte_data(client, TMP461_REG_DFC);
+
+		if ((local_ext & 0x0F) == 0x00 &&
+		    (conalert & 0xf1) == 0x01 &&
+		    (chen & 0xfc) == 0x00 &&
+		    (dfc & 0xfc) == 0x00) {
+			if (address == 0x4c && !(chen & 0x03))
+				name = "tmp451";
+			else if (address >= 0x48 && address <= 0x4f)
+				name = "tmp461";
+		}
 	}
 
 	if (!name) { /* identification failed */
@@ -1647,7 +1715,7 @@ static int lm90_init_client(struct i2c_client *client, struct lm90_data *data)
 	lm90_set_convrate(client, data, 500); /* 500ms; 2Hz conversion rate */
 
 	/* Check Temperature Range Select */
-	if (data->kind == adt7461 || data->kind == tmp451) {
+	if (data->flags & LM90_HAVE_EXTENDED_TEMP) {
 		if (config & 0x04)
 			data->flags |= LM90_FLAG_ADT7461_EXT;
 	}
@@ -1660,6 +1728,15 @@ static int lm90_init_client(struct i2c_client *client, struct lm90_data *data)
 	if (data->kind == max6680)
 		config |= 0x18;
 
+	/*
+	 * Put MAX6654 into extended range (0x20, extend minimum range from
+	 * 0 degrees to -64 degrees). Note that extended resolution is not
+	 * possible on the MAX6654 unless conversion rate is set to 1 Hz or
+	 * slower, which is intentionally not done by default.
+	 */
+	if (data->kind == max6654)
+		config |= 0x20;
+
 	/*
 	 * Select external channel 0 for max6695/96
 	 */
@@ -1806,11 +1883,14 @@ static int lm90_probe(struct i2c_client *client,
 	info->config = data->channel_config;
 
 	data->channel_config[0] = HWMON_T_INPUT | HWMON_T_MIN | HWMON_T_MAX |
-		HWMON_T_CRIT | HWMON_T_CRIT_HYST | HWMON_T_MIN_ALARM |
-		HWMON_T_MAX_ALARM | HWMON_T_CRIT_ALARM;
+		HWMON_T_MIN_ALARM | HWMON_T_MAX_ALARM;
 	data->channel_config[1] = HWMON_T_INPUT | HWMON_T_MIN | HWMON_T_MAX |
-		HWMON_T_CRIT | HWMON_T_CRIT_HYST | HWMON_T_MIN_ALARM |
-		HWMON_T_MAX_ALARM | HWMON_T_CRIT_ALARM | HWMON_T_FAULT;
+		HWMON_T_MIN_ALARM | HWMON_T_MAX_ALARM | HWMON_T_FAULT;
+
+	if (data->flags & LM90_HAVE_CRIT) {
+		data->channel_config[0] |= HWMON_T_CRIT | HWMON_T_CRIT_ALARM | HWMON_T_CRIT_HYST;
+		data->channel_config[1] |= HWMON_T_CRIT | HWMON_T_CRIT_ALARM | HWMON_T_CRIT_HYST;
+	}
 
 	if (data->flags & LM90_HAVE_OFFSET)
 		data->channel_config[1] |= HWMON_T_OFFSET;
diff --git linux-libre-5.4.168-gnu1/drivers/infiniband/hw/qib/qib_user_sdma.c linux-libre-5.4.169-gnu1/drivers/infiniband/hw/qib/qib_user_sdma.c
index 5fd28574124f..fde848b00202 100644
--- linux-libre-5.4.168-gnu1/drivers/infiniband/hw/qib/qib_user_sdma.c
+++ linux-libre-5.4.169-gnu1/drivers/infiniband/hw/qib/qib_user_sdma.c
@@ -941,7 +941,7 @@ static int qib_user_sdma_queue_pkts(const struct qib_devdata *dd,
 					       &addrlimit) ||
 			    addrlimit > type_max(typeof(pkt->addrlimit))) {
 				ret = -EINVAL;
-				goto free_pbc;
+				goto free_pkt;
 			}
 			pkt->addrlimit = addrlimit;
 
diff --git linux-libre-5.4.168-gnu1/drivers/input/mouse/elantech.c linux-libre-5.4.169-gnu1/drivers/input/mouse/elantech.c
index 0b5ed963cb0e..3e78c2602581 100644
--- linux-libre-5.4.168-gnu1/drivers/input/mouse/elantech.c
+++ linux-libre-5.4.169-gnu1/drivers/input/mouse/elantech.c
@@ -1588,7 +1588,13 @@ static const struct dmi_system_id no_hw_res_dmi_table[] = {
  */
 static int elantech_change_report_id(struct psmouse *psmouse)
 {
-	unsigned char param[2] = { 0x10, 0x03 };
+	/*
+	 * NOTE: the code is expecting to receive param[] as an array of 3
+	 * items (see __ps2_command()), even if in this case only 2 are
+	 * actually needed. Make sure the array size is 3 to avoid potential
+	 * stack out-of-bound accesses.
+	 */
+	unsigned char param[3] = { 0x10, 0x03 };
 
 	if (elantech_write_reg_params(psmouse, 0x7, param) ||
 	    elantech_read_reg_params(psmouse, 0x7, param) ||
diff --git linux-libre-5.4.168-gnu1/drivers/input/touchscreen/atmel_mxt_ts.c linux-libre-5.4.169-gnu1/drivers/input/touchscreen/atmel_mxt_ts.c
index 92cb9774da16..9d0273abdab4 100644
--- linux-libre-5.4.168-gnu1/drivers/input/touchscreen/atmel_mxt_ts.c
+++ linux-libre-5.4.169-gnu1/drivers/input/touchscreen/atmel_mxt_ts.c
@@ -1794,7 +1794,7 @@ static int mxt_read_info_block(struct mxt_data *data)
 	if (error) {
 		dev_err(&client->dev, "Error %d parsing object table\n", error);
 		mxt_free_object_table(data);
-		goto err_free_mem;
+		return error;
 	}
 
 	data->object_table = (struct mxt_object *)(id_buf + MXT_OBJECT_START);
diff --git linux-libre-5.4.168-gnu1/drivers/mmc/core/core.c linux-libre-5.4.169-gnu1/drivers/mmc/core/core.c
index 8f94c2539508..d7bda1fa0a6e 100644
--- linux-libre-5.4.168-gnu1/drivers/mmc/core/core.c
+++ linux-libre-5.4.169-gnu1/drivers/mmc/core/core.c
@@ -2364,7 +2364,7 @@ void mmc_start_host(struct mmc_host *host)
 	_mmc_detect_change(host, 0, false);
 }
 
-void mmc_stop_host(struct mmc_host *host)
+void __mmc_stop_host(struct mmc_host *host)
 {
 	if (host->slot.cd_irq >= 0) {
 		mmc_gpio_set_cd_wake(host, false);
@@ -2373,6 +2373,11 @@ void mmc_stop_host(struct mmc_host *host)
 
 	host->rescan_disable = 1;
 	cancel_delayed_work_sync(&host->detect);
+}
+
+void mmc_stop_host(struct mmc_host *host)
+{
+	__mmc_stop_host(host);
 
 	/* clear pm flags now and let card drivers set them as needed */
 	host->pm_flags = 0;
diff --git linux-libre-5.4.168-gnu1/drivers/mmc/core/core.h linux-libre-5.4.169-gnu1/drivers/mmc/core/core.h
index db3c9c68875d..a6c814fdbf0a 100644
--- linux-libre-5.4.168-gnu1/drivers/mmc/core/core.h
+++ linux-libre-5.4.169-gnu1/drivers/mmc/core/core.h
@@ -69,6 +69,7 @@ static inline void mmc_delay(unsigned int ms)
 
 void mmc_rescan(struct work_struct *work);
 void mmc_start_host(struct mmc_host *host);
+void __mmc_stop_host(struct mmc_host *host);
 void mmc_stop_host(struct mmc_host *host);
 
 void _mmc_detect_change(struct mmc_host *host, unsigned long delay,
diff --git linux-libre-5.4.168-gnu1/drivers/mmc/core/host.c linux-libre-5.4.169-gnu1/drivers/mmc/core/host.c
index f7339590a84c..e955f1ef2564 100644
--- linux-libre-5.4.168-gnu1/drivers/mmc/core/host.c
+++ linux-libre-5.4.169-gnu1/drivers/mmc/core/host.c
@@ -76,9 +76,18 @@ static void mmc_host_classdev_release(struct device *dev)
 	kfree(host);
 }
 
+static int mmc_host_classdev_shutdown(struct device *dev)
+{
+	struct mmc_host *host = cls_dev_to_mmc_host(dev);
+
+	__mmc_stop_host(host);
+	return 0;
+}
+
 static struct class mmc_host_class = {
 	.name		= "mmc_host",
 	.dev_release	= mmc_host_classdev_release,
+	.shutdown_pre	= mmc_host_classdev_shutdown,
 	.pm		= MMC_HOST_CLASS_DEV_PM_OPS,
 };
 
diff --git linux-libre-5.4.168-gnu1/drivers/mmc/host/sdhci-tegra.c linux-libre-5.4.169-gnu1/drivers/mmc/host/sdhci-tegra.c
index c105356ad4cb..65dfe75120ed 100644
--- linux-libre-5.4.168-gnu1/drivers/mmc/host/sdhci-tegra.c
+++ linux-libre-5.4.169-gnu1/drivers/mmc/host/sdhci-tegra.c
@@ -340,23 +340,6 @@ static void tegra_sdhci_set_tap(struct sdhci_host *host, unsigned int tap)
 	}
 }
 
-static void tegra_sdhci_hs400_enhanced_strobe(struct mmc_host *mmc,
-					      struct mmc_ios *ios)
-{
-	struct sdhci_host *host = mmc_priv(mmc);
-	u32 val;
-
-	val = sdhci_readl(host, SDHCI_TEGRA_VENDOR_SYS_SW_CTRL);
-
-	if (ios->enhanced_strobe)
-		val |= SDHCI_TEGRA_SYS_SW_CTRL_ENHANCED_STROBE;
-	else
-		val &= ~SDHCI_TEGRA_SYS_SW_CTRL_ENHANCED_STROBE;
-
-	sdhci_writel(host, val, SDHCI_TEGRA_VENDOR_SYS_SW_CTRL);
-
-}
-
 static void tegra_sdhci_reset(struct sdhci_host *host, u8 mask)
 {
 	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
@@ -768,6 +751,32 @@ static void tegra_sdhci_set_clock(struct sdhci_host *host, unsigned int clock)
 	}
 }
 
+static void tegra_sdhci_hs400_enhanced_strobe(struct mmc_host *mmc,
+					      struct mmc_ios *ios)
+{
+	struct sdhci_host *host = mmc_priv(mmc);
+	u32 val;
+
+	val = sdhci_readl(host, SDHCI_TEGRA_VENDOR_SYS_SW_CTRL);
+
+	if (ios->enhanced_strobe) {
+		val |= SDHCI_TEGRA_SYS_SW_CTRL_ENHANCED_STROBE;
+		/*
+		 * When CMD13 is sent from mmc_select_hs400es() after
+		 * switching to HS400ES mode, the bus is operating at
+		 * either MMC_HIGH_26_MAX_DTR or MMC_HIGH_52_MAX_DTR.
+		 * To meet Tegra SDHCI requirement at HS400ES mode, force SDHCI
+		 * interface clock to MMC_HS200_MAX_DTR (200 MHz) so that host
+		 * controller CAR clock and the interface clock are rate matched.
+		 */
+		tegra_sdhci_set_clock(host, MMC_HS200_MAX_DTR);
+	} else {
+		val &= ~SDHCI_TEGRA_SYS_SW_CTRL_ENHANCED_STROBE;
+	}
+
+	sdhci_writel(host, val, SDHCI_TEGRA_VENDOR_SYS_SW_CTRL);
+}
+
 static unsigned int tegra_sdhci_get_max_clock(struct sdhci_host *host)
 {
 	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
diff --git linux-libre-5.4.168-gnu1/drivers/net/bonding/bond_options.c linux-libre-5.4.169-gnu1/drivers/net/bonding/bond_options.c
index 215c10923289..933087d85549 100644
--- linux-libre-5.4.168-gnu1/drivers/net/bonding/bond_options.c
+++ linux-libre-5.4.169-gnu1/drivers/net/bonding/bond_options.c
@@ -1452,7 +1452,7 @@ static int bond_option_ad_actor_system_set(struct bonding *bond,
 		mac = (u8 *)&newval->value;
 	}
 
-	if (!is_valid_ether_addr(mac))
+	if (is_multicast_ether_addr(mac))
 		goto err;
 
 	netdev_dbg(bond->dev, "Setting ad_actor_system to %pM\n", mac);
diff --git linux-libre-5.4.168-gnu1/drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov.h linux-libre-5.4.169-gnu1/drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov.h
index 5f327659efa7..85b688f60b87 100644
--- linux-libre-5.4.168-gnu1/drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov.h
+++ linux-libre-5.4.169-gnu1/drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov.h
@@ -202,7 +202,7 @@ int qlcnic_sriov_get_vf_vport_info(struct qlcnic_adapter *,
 				   struct qlcnic_info *, u16);
 int qlcnic_sriov_cfg_vf_guest_vlan(struct qlcnic_adapter *, u16, u8);
 void qlcnic_sriov_free_vlans(struct qlcnic_adapter *);
-void qlcnic_sriov_alloc_vlans(struct qlcnic_adapter *);
+int qlcnic_sriov_alloc_vlans(struct qlcnic_adapter *);
 bool qlcnic_sriov_check_any_vlan(struct qlcnic_vf_info *);
 void qlcnic_sriov_del_vlan_id(struct qlcnic_sriov *,
 			      struct qlcnic_vf_info *, u16);
diff --git linux-libre-5.4.168-gnu1/drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_common.c linux-libre-5.4.169-gnu1/drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_common.c
index f7c2f32237cb..400bc2c3f222 100644
--- linux-libre-5.4.168-gnu1/drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_common.c
+++ linux-libre-5.4.169-gnu1/drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_common.c
@@ -433,7 +433,7 @@ static int qlcnic_sriov_set_guest_vlan_mode(struct qlcnic_adapter *adapter,
 					    struct qlcnic_cmd_args *cmd)
 {
 	struct qlcnic_sriov *sriov = adapter->ahw->sriov;
-	int i, num_vlans;
+	int i, num_vlans, ret;
 	u16 *vlans;
 
 	if (sriov->allowed_vlans)
@@ -444,7 +444,9 @@ static int qlcnic_sriov_set_guest_vlan_mode(struct qlcnic_adapter *adapter,
 	dev_info(&adapter->pdev->dev, "Number of allowed Guest VLANs = %d\n",
 		 sriov->num_allowed_vlans);
 
-	qlcnic_sriov_alloc_vlans(adapter);
+	ret = qlcnic_sriov_alloc_vlans(adapter);
+	if (ret)
+		return ret;
 
 	if (!sriov->any_vlan)
 		return 0;
@@ -2160,7 +2162,7 @@ static int qlcnic_sriov_vf_resume(struct qlcnic_adapter *adapter)
 	return err;
 }
 
-void qlcnic_sriov_alloc_vlans(struct qlcnic_adapter *adapter)
+int qlcnic_sriov_alloc_vlans(struct qlcnic_adapter *adapter)
 {
 	struct qlcnic_sriov *sriov = adapter->ahw->sriov;
 	struct qlcnic_vf_info *vf;
@@ -2170,7 +2172,11 @@ void qlcnic_sriov_alloc_vlans(struct qlcnic_adapter *adapter)
 		vf = &sriov->vf_info[i];
 		vf->sriov_vlans = kcalloc(sriov->num_allowed_vlans,
 					  sizeof(*vf->sriov_vlans), GFP_KERNEL);
+		if (!vf->sriov_vlans)
+			return -ENOMEM;
 	}
+
+	return 0;
 }
 
 void qlcnic_sriov_free_vlans(struct qlcnic_adapter *adapter)
diff --git linux-libre-5.4.168-gnu1/drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_pf.c linux-libre-5.4.169-gnu1/drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_pf.c
index 5632da05145a..ed218ed2f466 100644
--- linux-libre-5.4.168-gnu1/drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_pf.c
+++ linux-libre-5.4.169-gnu1/drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_pf.c
@@ -598,7 +598,9 @@ static int __qlcnic_pci_sriov_enable(struct qlcnic_adapter *adapter,
 	if (err)
 		goto del_flr_queue;
 
-	qlcnic_sriov_alloc_vlans(adapter);
+	err = qlcnic_sriov_alloc_vlans(adapter);
+	if (err)
+		goto del_flr_queue;
 
 	return err;
 
diff --git linux-libre-5.4.168-gnu1/drivers/net/ethernet/sfc/falcon/rx.c linux-libre-5.4.169-gnu1/drivers/net/ethernet/sfc/falcon/rx.c
index 05ea3523890a..d516f81ab37a 100644
--- linux-libre-5.4.168-gnu1/drivers/net/ethernet/sfc/falcon/rx.c
+++ linux-libre-5.4.169-gnu1/drivers/net/ethernet/sfc/falcon/rx.c
@@ -726,7 +726,10 @@ static void ef4_init_rx_recycle_ring(struct ef4_nic *efx,
 					    efx->rx_bufs_per_page);
 	rx_queue->page_ring = kcalloc(page_ring_size,
 				      sizeof(*rx_queue->page_ring), GFP_KERNEL);
-	rx_queue->page_ptr_mask = page_ring_size - 1;
+	if (!rx_queue->page_ring)
+		rx_queue->page_ptr_mask = 0;
+	else
+		rx_queue->page_ptr_mask = page_ring_size - 1;
 }
 
 void ef4_init_rx_queue(struct ef4_rx_queue *rx_queue)
diff --git linux-libre-5.4.168-gnu1/drivers/net/ethernet/smsc/smc911x.c linux-libre-5.4.169-gnu1/drivers/net/ethernet/smsc/smc911x.c
index 7b65e79d6ae9..82ca29b6781b 100644
--- linux-libre-5.4.168-gnu1/drivers/net/ethernet/smsc/smc911x.c
+++ linux-libre-5.4.169-gnu1/drivers/net/ethernet/smsc/smc911x.c
@@ -2069,6 +2069,11 @@ static int smc911x_drv_probe(struct platform_device *pdev)
 
 	ndev->dma = (unsigned char)-1;
 	ndev->irq = platform_get_irq(pdev, 0);
+	if (ndev->irq < 0) {
+		ret = ndev->irq;
+		goto release_both;
+	}
+
 	lp = netdev_priv(ndev);
 	lp->netdev = ndev;
 #ifdef SMC_DYNAMIC_BUS_CONFIG
diff --git linux-libre-5.4.168-gnu1/drivers/net/fjes/fjes_main.c linux-libre-5.4.169-gnu1/drivers/net/fjes/fjes_main.c
index b89b4a3800a4..bef0133696c3 100644
--- linux-libre-5.4.168-gnu1/drivers/net/fjes/fjes_main.c
+++ linux-libre-5.4.169-gnu1/drivers/net/fjes/fjes_main.c
@@ -1269,6 +1269,11 @@ static int fjes_probe(struct platform_device *plat_dev)
 	hw->hw_res.start = res->start;
 	hw->hw_res.size = resource_size(res);
 	hw->hw_res.irq = platform_get_irq(plat_dev, 0);
+	if (hw->hw_res.irq < 0) {
+		err = hw->hw_res.irq;
+		goto err_free_control_wq;
+	}
+
 	err = fjes_hw_init(&adapter->hw);
 	if (err)
 		goto err_free_control_wq;
diff --git linux-libre-5.4.168-gnu1/drivers/net/hamradio/mkiss.c linux-libre-5.4.169-gnu1/drivers/net/hamradio/mkiss.c
index 352f9e75954c..d2eb33f53993 100644
--- linux-libre-5.4.168-gnu1/drivers/net/hamradio/mkiss.c
+++ linux-libre-5.4.169-gnu1/drivers/net/hamradio/mkiss.c
@@ -793,13 +793,14 @@ static void mkiss_close(struct tty_struct *tty)
 	 */
 	netif_stop_queue(ax->dev);
 
-	/* Free all AX25 frame buffers. */
+	unregister_netdev(ax->dev);
+
+	/* Free all AX25 frame buffers after unreg. */
 	kfree(ax->rbuff);
 	kfree(ax->xbuff);
 
 	ax->tty = NULL;
 
-	unregister_netdev(ax->dev);
 	free_netdev(ax->dev);
 }
 
diff --git linux-libre-5.4.168-gnu1/drivers/net/usb/lan78xx.c linux-libre-5.4.169-gnu1/drivers/net/usb/lan78xx.c
index 2d98373f7a71..ce3c8f476d75 100644
--- linux-libre-5.4.168-gnu1/drivers/net/usb/lan78xx.c
+++ linux-libre-5.4.169-gnu1/drivers/net/usb/lan78xx.c
@@ -64,6 +64,8 @@
 #define LAN7801_USB_PRODUCT_ID		(0x7801)
 #define LAN78XX_EEPROM_MAGIC		(0x78A5)
 #define LAN78XX_OTP_MAGIC		(0x78F3)
+#define AT29M2AF_USB_VENDOR_ID		(0x07C9)
+#define AT29M2AF_USB_PRODUCT_ID	(0x0012)
 
 #define	MII_READ			1
 #define	MII_WRITE			0
@@ -4153,6 +4155,10 @@ static const struct usb_device_id products[] = {
 	/* LAN7801 USB Gigabit Ethernet Device */
 	USB_DEVICE(LAN78XX_USB_VENDOR_ID, LAN7801_USB_PRODUCT_ID),
 	},
+	{
+	/* ATM2-AF USB Gigabit Ethernet Device */
+	USB_DEVICE(AT29M2AF_USB_VENDOR_ID, AT29M2AF_USB_PRODUCT_ID),
+	},
 	{},
 };
 MODULE_DEVICE_TABLE(usb, products);
diff --git linux-libre-5.4.168-gnu1/drivers/pinctrl/mediatek/pinctrl-mtk-common-v2.c linux-libre-5.4.169-gnu1/drivers/pinctrl/mediatek/pinctrl-mtk-common-v2.c
index 20e1c890e73b..c3e6f3c1b474 100644
--- linux-libre-5.4.168-gnu1/drivers/pinctrl/mediatek/pinctrl-mtk-common-v2.c
+++ linux-libre-5.4.169-gnu1/drivers/pinctrl/mediatek/pinctrl-mtk-common-v2.c
@@ -236,8 +236,12 @@ static int mtk_xt_get_gpio_n(void *data, unsigned long eint_n,
 	desc = (const struct mtk_pin_desc *)hw->soc->pins;
 	*gpio_chip = &hw->chip;
 
-	/* Be greedy to guess first gpio_n is equal to eint_n */
-	if (desc[eint_n].eint.eint_n == eint_n)
+	/*
+	 * Be greedy to guess first gpio_n is equal to eint_n.
+	 * Only eint virtual eint number is greater than gpio number.
+	 */
+	if (hw->soc->npins > eint_n &&
+	    desc[eint_n].eint.eint_n == eint_n)
 		*gpio_n = eint_n;
 	else
 		*gpio_n = mtk_xt_find_eint_num(hw, eint_n);
diff --git linux-libre-5.4.168-gnu1/drivers/pinctrl/stm32/pinctrl-stm32.c linux-libre-5.4.169-gnu1/drivers/pinctrl/stm32/pinctrl-stm32.c
index 138cbc012cd8..f9abd4364fba 100644
--- linux-libre-5.4.168-gnu1/drivers/pinctrl/stm32/pinctrl-stm32.c
+++ linux-libre-5.4.169-gnu1/drivers/pinctrl/stm32/pinctrl-stm32.c
@@ -1186,10 +1186,10 @@ static int stm32_gpiolib_register_bank(struct stm32_pinctrl *pctl,
 		bank_nr = args.args[1] / STM32_GPIO_PINS_PER_BANK;
 		bank->gpio_chip.base = args.args[1];
 
-		npins = args.args[2];
-		while (!of_parse_phandle_with_fixed_args(np, "gpio-ranges", 3,
-							 ++i, &args))
-			npins += args.args[2];
+		/* get the last defined gpio line (offset + nb of pins) */
+		npins = args.args[0] + args.args[2];
+		while (!of_parse_phandle_with_fixed_args(np, "gpio-ranges", 3, ++i, &args))
+			npins = max(npins, (int)(args.args[0] + args.args[2]));
 	} else {
 		bank_nr = pctl->nbanks;
 		bank->gpio_chip.base = bank_nr * STM32_GPIO_PINS_PER_BANK;
diff --git linux-libre-5.4.168-gnu1/drivers/spi/spi-armada-3700.c linux-libre-5.4.169-gnu1/drivers/spi/spi-armada-3700.c
index e450ee17787f..4a4e2877414a 100644
--- linux-libre-5.4.168-gnu1/drivers/spi/spi-armada-3700.c
+++ linux-libre-5.4.169-gnu1/drivers/spi/spi-armada-3700.c
@@ -906,7 +906,7 @@ static int a3700_spi_probe(struct platform_device *pdev)
 	return 0;
 
 error_clk:
-	clk_disable_unprepare(spi->clk);
+	clk_unprepare(spi->clk);
 error:
 	spi_master_put(master);
 out:
diff --git linux-libre-5.4.168-gnu1/drivers/tee/optee/shm_pool.c linux-libre-5.4.169-gnu1/drivers/tee/optee/shm_pool.c
index c41a9a501a6e..fa75024f16f7 100644
--- linux-libre-5.4.168-gnu1/drivers/tee/optee/shm_pool.c
+++ linux-libre-5.4.169-gnu1/drivers/tee/optee/shm_pool.c
@@ -41,10 +41,8 @@ static int pool_op_alloc(struct tee_shm_pool_mgr *poolm,
 			goto err;
 		}
 
-		for (i = 0; i < nr_pages; i++) {
-			pages[i] = page;
-			page++;
-		}
+		for (i = 0; i < nr_pages; i++)
+			pages[i] = page + i;
 
 		shm->flags |= TEE_SHM_REGISTER;
 		rc = optee_shm_register(shm->ctx, shm, pages, nr_pages,
diff --git linux-libre-5.4.168-gnu1/drivers/tty/serial/8250/8250_fintek.c linux-libre-5.4.169-gnu1/drivers/tty/serial/8250/8250_fintek.c
index 31c91c2f8c6e..e24161004ddc 100644
--- linux-libre-5.4.168-gnu1/drivers/tty/serial/8250/8250_fintek.c
+++ linux-libre-5.4.169-gnu1/drivers/tty/serial/8250/8250_fintek.c
@@ -285,24 +285,6 @@ static void fintek_8250_set_max_fifo(struct fintek_8250 *pdata)
 	}
 }
 
-static void fintek_8250_goto_highspeed(struct uart_8250_port *uart,
-			      struct fintek_8250 *pdata)
-{
-	sio_write_reg(pdata, LDN, pdata->index);
-
-	switch (pdata->pid) {
-	case CHIP_ID_F81866: /* set uart clock for high speed serial mode */
-		sio_write_mask_reg(pdata, F81866_UART_CLK,
-			F81866_UART_CLK_MASK,
-			F81866_UART_CLK_14_769MHZ);
-
-		uart->port.uartclk = 921600 * 16;
-		break;
-	default: /* leave clock speed untouched */
-		break;
-	}
-}
-
 static void fintek_8250_set_termios(struct uart_port *port,
 				    struct ktermios *termios,
 				    struct ktermios *old)
@@ -422,7 +404,6 @@ static int probe_setup_port(struct fintek_8250 *pdata,
 
 				fintek_8250_set_irq_mode(pdata, level_mode);
 				fintek_8250_set_max_fifo(pdata);
-				fintek_8250_goto_highspeed(uart, pdata);
 
 				fintek_8250_exit_key(addr[i]);
 
diff --git linux-libre-5.4.168-gnu1/drivers/usb/gadget/function/u_ether.c linux-libre-5.4.169-gnu1/drivers/usb/gadget/function/u_ether.c
index 57da62e33184..271bd08f4a25 100644
--- linux-libre-5.4.168-gnu1/drivers/usb/gadget/function/u_ether.c
+++ linux-libre-5.4.169-gnu1/drivers/usb/gadget/function/u_ether.c
@@ -860,19 +860,23 @@ int gether_register_netdev(struct net_device *net)
 {
 	struct eth_dev *dev;
 	struct usb_gadget *g;
-	struct sockaddr sa;
 	int status;
 
 	if (!net->dev.parent)
 		return -EINVAL;
 	dev = netdev_priv(net);
 	g = dev->gadget;
+
+	memcpy(net->dev_addr, dev->dev_mac, ETH_ALEN);
+	net->addr_assign_type = NET_ADDR_RANDOM;
+
 	status = register_netdev(net);
 	if (status < 0) {
 		dev_dbg(&g->dev, "register_netdev failed, %d\n", status);
 		return status;
 	} else {
 		INFO(dev, "HOST MAC %pM\n", dev->host_mac);
+		INFO(dev, "MAC %pM\n", dev->dev_mac);
 
 		/* two kinds of host-initiated state changes:
 		 *  - iff DATA transfer is active, carrier is "on"
@@ -880,15 +884,6 @@ int gether_register_netdev(struct net_device *net)
 		 */
 		netif_carrier_off(net);
 	}
-	sa.sa_family = net->type;
-	memcpy(sa.sa_data, dev->dev_mac, ETH_ALEN);
-	rtnl_lock();
-	status = dev_set_mac_address(net, &sa, NULL);
-	rtnl_unlock();
-	if (status)
-		pr_warn("cannot set self ethernet address: %d\n", status);
-	else
-		INFO(dev, "MAC %pM\n", dev->dev_mac);
 
 	return status;
 }
diff --git linux-libre-5.4.168-gnu1/fs/f2fs/xattr.c linux-libre-5.4.169-gnu1/fs/f2fs/xattr.c
index 296b3189448a..cf1bfed1e662 100644
--- linux-libre-5.4.168-gnu1/fs/f2fs/xattr.c
+++ linux-libre-5.4.169-gnu1/fs/f2fs/xattr.c
@@ -661,8 +661,17 @@ static int __f2fs_setxattr(struct inode *inode, int index,
 	}
 
 	last = here;
-	while (!IS_XATTR_LAST_ENTRY(last))
+	while (!IS_XATTR_LAST_ENTRY(last)) {
+		if ((void *)(last) + sizeof(__u32) > last_base_addr ||
+			(void *)XATTR_NEXT_ENTRY(last) > last_base_addr) {
+			f2fs_err(F2FS_I_SB(inode), "inode (%lu) has invalid last xattr entry, entry_size: %zu",
+					inode->i_ino, ENTRY_SIZE(last));
+			set_sbi_flag(F2FS_I_SB(inode), SBI_NEED_FSCK);
+			error = -EFSCORRUPTED;
+			goto exit;
+		}
 		last = XATTR_NEXT_ENTRY(last);
+	}
 
 	newsize = XATTR_ALIGN(sizeof(struct f2fs_xattr_entry) + len + size);
 
diff --git linux-libre-5.4.168-gnu1/include/linux/virtio_net.h linux-libre-5.4.169-gnu1/include/linux/virtio_net.h
index 04e87f4b9417..a960de68ac69 100644
--- linux-libre-5.4.168-gnu1/include/linux/virtio_net.h
+++ linux-libre-5.4.169-gnu1/include/linux/virtio_net.h
@@ -7,9 +7,27 @@
 #include <uapi/linux/udp.h>
 #include <uapi/linux/virtio_net.h>
 
+static inline bool virtio_net_hdr_match_proto(__be16 protocol, __u8 gso_type)
+{
+	switch (gso_type & ~VIRTIO_NET_HDR_GSO_ECN) {
+	case VIRTIO_NET_HDR_GSO_TCPV4:
+		return protocol == cpu_to_be16(ETH_P_IP);
+	case VIRTIO_NET_HDR_GSO_TCPV6:
+		return protocol == cpu_to_be16(ETH_P_IPV6);
+	case VIRTIO_NET_HDR_GSO_UDP:
+		return protocol == cpu_to_be16(ETH_P_IP) ||
+		       protocol == cpu_to_be16(ETH_P_IPV6);
+	default:
+		return false;
+	}
+}
+
 static inline int virtio_net_hdr_set_proto(struct sk_buff *skb,
 					   const struct virtio_net_hdr *hdr)
 {
+	if (skb->protocol)
+		return 0;
+
 	switch (hdr->gso_type & ~VIRTIO_NET_HDR_GSO_ECN) {
 	case VIRTIO_NET_HDR_GSO_TCPV4:
 	case VIRTIO_NET_HDR_GSO_UDP:
@@ -88,9 +106,12 @@ static inline int virtio_net_hdr_to_skb(struct sk_buff *skb,
 			if (!skb->protocol) {
 				__be16 protocol = dev_parse_header_protocol(skb);
 
-				virtio_net_hdr_set_proto(skb, hdr);
-				if (protocol && protocol != skb->protocol)
+				if (!protocol)
+					virtio_net_hdr_set_proto(skb, hdr);
+				else if (!virtio_net_hdr_match_proto(protocol, hdr->gso_type))
 					return -EINVAL;
+				else
+					skb->protocol = protocol;
 			}
 retry:
 			if (!skb_flow_dissect_flow_keys_basic(NULL, skb, &keys,
diff --git linux-libre-5.4.168-gnu1/mm/mempolicy.c linux-libre-5.4.169-gnu1/mm/mempolicy.c
index 87d165923fee..2c4082f71d25 100644
--- linux-libre-5.4.168-gnu1/mm/mempolicy.c
+++ linux-libre-5.4.169-gnu1/mm/mempolicy.c
@@ -2143,8 +2143,9 @@ alloc_pages_vma(gfp_t gfp, int order, struct vm_area_struct *vma,
 			 * memory as well.
 			 */
 			if (!page && (gfp & __GFP_DIRECT_RECLAIM))
-				page = __alloc_pages_node(hpage_node,
-						gfp | __GFP_NORETRY, order);
+				page = __alloc_pages_nodemask(gfp | __GFP_NORETRY,
+							order, hpage_node,
+							nmask);
 
 			goto out;
 		}
diff --git linux-libre-5.4.168-gnu1/net/ax25/af_ax25.c linux-libre-5.4.169-gnu1/net/ax25/af_ax25.c
index 2fdb1b573e8c..1f84d41e22c3 100644
--- linux-libre-5.4.168-gnu1/net/ax25/af_ax25.c
+++ linux-libre-5.4.169-gnu1/net/ax25/af_ax25.c
@@ -85,8 +85,10 @@ static void ax25_kill_by_device(struct net_device *dev)
 again:
 	ax25_for_each(s, &ax25_list) {
 		if (s->ax25_dev == ax25_dev) {
-			s->ax25_dev = NULL;
 			spin_unlock_bh(&ax25_list_lock);
+			lock_sock(s->sk);
+			s->ax25_dev = NULL;
+			release_sock(s->sk);
 			ax25_disconnect(s, ENETUNREACH);
 			spin_lock_bh(&ax25_list_lock);
 
diff --git linux-libre-5.4.168-gnu1/net/netfilter/nfnetlink_log.c linux-libre-5.4.169-gnu1/net/netfilter/nfnetlink_log.c
index 7ca2ca4bba05..b36af4741ad3 100644
--- linux-libre-5.4.168-gnu1/net/netfilter/nfnetlink_log.c
+++ linux-libre-5.4.169-gnu1/net/netfilter/nfnetlink_log.c
@@ -557,7 +557,8 @@ __build_packet_message(struct nfnl_log_net *log,
 		goto nla_put_failure;
 
 	if (indev && skb->dev &&
-	    skb->mac_header != skb->network_header) {
+	    skb_mac_header_was_set(skb) &&
+	    skb_mac_header_len(skb) != 0) {
 		struct nfulnl_msg_packet_hw phw;
 		int len;
 
diff --git linux-libre-5.4.168-gnu1/net/netfilter/nfnetlink_queue.c linux-libre-5.4.169-gnu1/net/netfilter/nfnetlink_queue.c
index a8cb562da3fe..ca21f8f4a47c 100644
--- linux-libre-5.4.168-gnu1/net/netfilter/nfnetlink_queue.c
+++ linux-libre-5.4.169-gnu1/net/netfilter/nfnetlink_queue.c
@@ -562,7 +562,8 @@ nfqnl_build_packet_message(struct net *net, struct nfqnl_instance *queue,
 		goto nla_put_failure;
 
 	if (indev && entskb->dev &&
-	    skb_mac_header_was_set(entskb)) {
+	    skb_mac_header_was_set(entskb) &&
+	    skb_mac_header_len(entskb) != 0) {
 		struct nfqnl_msg_packet_hw phw;
 		int len;
 
diff --git linux-libre-5.4.168-gnu1/net/phonet/pep.c linux-libre-5.4.169-gnu1/net/phonet/pep.c
index 4577e43cb777..a07e13f63332 100644
--- linux-libre-5.4.168-gnu1/net/phonet/pep.c
+++ linux-libre-5.4.169-gnu1/net/phonet/pep.c
@@ -946,6 +946,8 @@ static int pep_ioctl(struct sock *sk, int cmd, unsigned long arg)
 			ret =  -EBUSY;
 		else if (sk->sk_state == TCP_ESTABLISHED)
 			ret = -EISCONN;
+		else if (!pn->pn_sk.sobject)
+			ret = -EADDRNOTAVAIL;
 		else
 			ret = pep_sock_enable(sk, NULL, 0);
 		release_sock(sk);
diff --git linux-libre-5.4.168-gnu1/sound/core/jack.c linux-libre-5.4.169-gnu1/sound/core/jack.c
index fb26196571a7..8b209750c7a9 100644
--- linux-libre-5.4.168-gnu1/sound/core/jack.c
+++ linux-libre-5.4.169-gnu1/sound/core/jack.c
@@ -220,6 +220,10 @@ int snd_jack_new(struct snd_card *card, const char *id, int type,
 		return -ENOMEM;
 
 	jack->id = kstrdup(id, GFP_KERNEL);
+	if (jack->id == NULL) {
+		kfree(jack);
+		return -ENOMEM;
+	}
 
 	/* don't creat input device for phantom jack */
 	if (!phantom_jack) {
diff --git linux-libre-5.4.168-gnu1/sound/drivers/opl3/opl3_midi.c linux-libre-5.4.169-gnu1/sound/drivers/opl3/opl3_midi.c
index 280cc79870cf..ce38ec09d408 100644
--- linux-libre-5.4.168-gnu1/sound/drivers/opl3/opl3_midi.c
+++ linux-libre-5.4.169-gnu1/sound/drivers/opl3/opl3_midi.c
@@ -398,7 +398,7 @@ void snd_opl3_note_on(void *p, int note, int vel, struct snd_midi_channel *chan)
 	}
 	if (instr_4op) {
 		vp2 = &opl3->voices[voice + 3];
-		if (vp->state > 0) {
+		if (vp2->state > 0) {
 			opl3_reg = reg_side | (OPL3_REG_KEYON_BLOCK +
 					       voice_offset + 3);
 			reg_val = vp->keyon_reg & ~OPL3_KEYON_BIT;
diff --git linux-libre-5.4.168-gnu1/sound/pci/hda/patch_realtek.c linux-libre-5.4.169-gnu1/sound/pci/hda/patch_realtek.c
index 9514db7c2a86..022799479a72 100644
--- linux-libre-5.4.168-gnu1/sound/pci/hda/patch_realtek.c
+++ linux-libre-5.4.169-gnu1/sound/pci/hda/patch_realtek.c
@@ -8101,6 +8101,7 @@ static const struct snd_pci_quirk alc269_fixup_tbl[] = {
 	SND_PCI_QUIRK(0x103c, 0x84da, "HP OMEN dc0019-ur", ALC295_FIXUP_HP_OMEN),
 	SND_PCI_QUIRK(0x103c, 0x84e7, "HP Pavilion 15", ALC269_FIXUP_HP_MUTE_LED_MIC3),
 	SND_PCI_QUIRK(0x103c, 0x8519, "HP Spectre x360 15-df0xxx", ALC285_FIXUP_HP_SPECTRE_X360),
+	SND_PCI_QUIRK(0x103c, 0x860f, "HP ZBook 15 G6", ALC285_FIXUP_HP_GPIO_AMP_INIT),
 	SND_PCI_QUIRK(0x103c, 0x861f, "HP Elite Dragonfly G1", ALC285_FIXUP_HP_GPIO_AMP_INIT),
 	SND_PCI_QUIRK(0x103c, 0x869d, "HP", ALC236_FIXUP_HP_MUTE_LED),
 	SND_PCI_QUIRK(0x103c, 0x8724, "HP EliteBook 850 G7", ALC285_FIXUP_HP_GPIO_LED),
