diff --git a/.gitignore b/.gitignore index c2ed4ecb0..0544d5077 100644 --- a/.gitignore +++ b/.gitignore @@ -114,3 +114,7 @@ all.config # Kdevelop4 *.kdev4 + +# dtb objects +*.dtb +*.dtbo diff --git b/Documentation/ABI/testing/sysfs-devices-platform-bone_capemgr b/Documentation/ABI/testing/sysfs-devices-platform-bone_capemgr new file mode 100644 index 000000000..e2df61358 --- /dev/null +++ b/Documentation/ABI/testing/sysfs-devices-platform-bone_capemgr @@ -0,0 +1,63 @@ +What: /sys/devices/platform/bone_capemgr/slots +Date: May 2015 +KernelVersion: 4.0 +Contact: Pantelis Antoniou +Description: + READ: + Describe the state of all the slots of the beaglebone capemgr. + Each line of the output describes a slot: + The slot format is as following: + : [P-][F-][O-][l-][L-][D-] \ + ,, + , + + Where the flags are: + P: Slot has been probed + F: Slot has failed probing (i.e. no EEPROM detected) + O: Slot has been overridden by the user + l: Slot is current loading + L: Slot has completed loading and is ready + D: Slot has been disabled + + Example: + 0: P---L- -1 BeagleBone RS232 CAPE,00A1,Beagleboardtoys,BB-BONE-SERL-03 + 1: PF---- -1 + 2: PF---- -1 + 3: PF---- -1 + + WRITE: + Writing a string of the form [:version] issues a request to + load a firmware blob containing an overlay. The name of the firmware blob + is -[version|00A0].dtbo. This act is defined as a slot override. + + Writing a negative slot id removes the slot if it was an overridden one, or + unloads a slot that was probed. + +What: /sys/devices/platform/bone_capemgr/baseboard/ +Date: May 2015 +KernelVersion: 4.0 +Contact: Pantelis Antoniou +Description: Contains the probed base board EEPROM field; one of: + board-name - board-name as stored in cape EEPROM + dc-supplied - whether the cape draws or supplies DC + eeprom-format-revision - EEPROM format rev, only 00A0 supported + header - header; should be 'aa 55 33 ee' + manufacturer - manufacturer string + part-number - part-number of the cape + serial-number - serial number of the cape + version - version of the cape, i.e. 00A0 + number-of-pins - displayed but ignored + pin-usage - displayed but ignored + sys-5v - displayed but ignored + vdd-3v3exp - displayed but ignored + vdd-5v - displayed but ignored +What: /sys/devices/platform/bone_capemgr/slot-/ +Date: May 2015 +KernelVersion: 4.0 +Contact: Pantelis Antoniou +Description: Contains the probed cape's EEPROM field; the field is one of: + board-name - baseboard name i.e. A335BNLT + header - header; should be 'aa 55 33 ee' + revision - baseboard revision + serial-number - baseboard serial number + config-option - displayed but ignored diff --git b/Documentation/ABI/testing/sysfs-firmware-devicetree-overlays b/Documentation/ABI/testing/sysfs-firmware-devicetree-overlays new file mode 100644 index 000000000..88d15498a --- /dev/null +++ b/Documentation/ABI/testing/sysfs-firmware-devicetree-overlays @@ -0,0 +1,52 @@ +What: /sys/firmware/devicetree/overlays/ +Date: October 2015 +Contact: Pantelis Antoniou +Description: + This directory contains the applied device tree overlays of + the running system, as directories of the overlay id. + +What: /sys/firmware/devicetree/overlays/enable +Date: October 2015 +Contact: Pantelis Antoniou +Description: + The master enable switch, by default is 1, and when + set to 0 it cannot be re-enabled for security reasons. + + The discussion about this switch takes place in: + http://comments.gmane.org/gmane.linux.drivers.devicetree/101871 + + Kees Cook: + "Coming from the perspective of drawing a bright line between + kernel and the root user (which tends to start with disabling + kernel module loading), I would say that there at least needs + to be a high-level one-way "off" switch for the interface so + that systems that have this interface can choose to turn it off + during initial boot, etc." + +What: /sys/firmware/devicetree/overlays/ +Date: October 2015 +Contact: Pantelis Antoniou +Description: + Each directory represents an applied overlay, containing + the following attribute files. + +What: /sys/firmware/devicetree/overlays//can_remove +Date: October 2015 +Contact: Pantelis Antoniou +Description: + The attribute set to 1 means that the overlay can be removed, + while 0 means that the overlay is being overlapped therefore + removal is prohibited. + +What: /sys/firmware/devicetree/overlays/// +Date: October 2015 +Contact: Pantelis Antoniou +Description: + Each of these directories contain information about of the + particular overlay fragment. + +What: /sys/firmware/devicetree/overlays///target +Date: October 2015 +Contact: Pantelis Antoniou +Description: + The full-path of the target of the fragment diff --git a/Documentation/devicetree/bindings/arm/omap/omap.txt b/Documentation/devicetree/bindings/arm/omap/omap.txt index f53e2ee65..29bc4fe92 100644 --- a/Documentation/devicetree/bindings/arm/omap/omap.txt +++ b/Documentation/devicetree/bindings/arm/omap/omap.txt @@ -24,6 +24,8 @@ Optional properties: - ti,no-reset-on-init: When present, the module should not be reset at init - ti,no-idle-on-init: When present, the module should not be idled at init - ti,no-idle: When present, the module is never allowed to idle. +- ti,deassert-hard-reset: list of hwmod and hardware reset line name pairs + (ascii strings) to be deasserted upon device instantiation. Example: diff --git b/Documentation/devicetree/bindings/cpufreq/ti-cpufreq.txt b/Documentation/devicetree/bindings/cpufreq/ti-cpufreq.txt new file mode 100644 index 000000000..7a318647f --- /dev/null +++ b/Documentation/devicetree/bindings/cpufreq/ti-cpufreq.txt @@ -0,0 +1,132 @@ +TI CPUFreq and OPP bindings +================================ + +Certain TI SoCs, like those in the am335x, am437x, am57xx, and dra7xx +families support different OPPs depending on the silicon variant in use. +The ti_cpufreq driver can use revision and an efuse value from the SoC to +provide the OPP framework with supported hardware information. This is +used to determine which OPPs from the operating-points-v2 table get enabled +when it is parsed by the OPP framework. + +Required properties: +-------------------- +In 'cpus' nodes: +- operating-points-v2: Phandle to the operating-points-v2 table to use. + +In 'operating-points-v2' table: +- compatible: Should be + - 'operating-points-v2-ti' for am335x, am43xx, and dra7xx/am57xx SoCs +- ti,syscon-efuse: Syscon phandle, offset to efuse register, efuse register + mask, and efuse register shift to get the relevant bits + that describe OPP availability. +- ti,syscon-rev: Syscon and offset used to look up revision value on SoC. + +Optional properties: +-------------------- +For each opp entry in 'operating-points-v2' table: +- opp-supported-hw: Two bitfields indicating: + 1. Which revision of the SoC the OPP is supported by + 2. Which eFuse bits indicate this OPP is available + + A bitwise AND is performed against these values and if any bit + matches, the OPP gets enabled. Not providing the property for an + entry indicates that an OPP is always supported. + +Example: +-------- + +/* From arch/arm/boot/dts/am33xx.dtsi */ +cpus { + #address-cells = <1>; + #size-cells = <0>; + cpu@0 { + compatible = "arm,cortex-a8"; + device_type = "cpu"; + reg = <0>; + + operating-points-v2 = <&cpu0_opp_table>; + + clocks = <&dpll_mpu_ck>; + clock-names = "cpu"; + + clock-latency = <300000>; /* From omap-cpufreq driver */ + }; +}; + +/* + * cpu0 has different OPPs depending on SoC revision and some on revisions + * 0x2 and 0x4 have eFuse bits that indicate if they are available or not + */ +cpu0_opp_table: opp_table0 { + compatible = "operating-points-v2-ti-am3352-cpu"; + ti,syscon-efuse = <&scm_conf 0x7fc 0x1fff 0>; + ti,syscon-rev = <&scm_conf 0x600>; + + /* + * The three following nodes are marked with opp-suspend + * because they can not be enabled simultaneously on a + * single SoC. + */ + opp50@300000000 { + opp-hz = /bits/ 64 <300000000>; + opp-microvolt = <950000 931000 969000>; + opp-supported-hw = <0x06 0x0010>; + opp-suspend; + }; + + opp100@275000000 { + opp-hz = /bits/ 64 <275000000>; + opp-microvolt = <1100000 1078000 1122000>; + opp-supported-hw = <0x01 0x00FF>; + opp-suspend; + }; + + opp100@300000000 { + opp-hz = /bits/ 64 <300000000>; + opp-microvolt = <1100000 1078000 1122000>; + opp-supported-hw = <0x06 0x0020>; + opp-suspend; + }; + + opp100@500000000 { + opp-hz = /bits/ 64 <500000000>; + opp-microvolt = <1100000 1078000 1122000>; + opp-supported-hw = <0x01 0xFFFF>; + }; + + opp100@600000000 { + opp-hz = /bits/ 64 <600000000>; + opp-microvolt = <1100000 1078000 1122000>; + opp-supported-hw = <0x06 0x0040>; + }; + + opp120@600000000 { + opp-hz = /bits/ 64 <600000000>; + opp-microvolt = <1200000 1176000 1224000>; + opp-supported-hw = <0x01 0xFFFF>; + }; + + opp120@720000000 { + opp-hz = /bits/ 64 <720000000>; + opp-microvolt = <1200000 1176000 1224000>; + opp-supported-hw = <0x06 0x0080>; + }; + + oppturbo@720000000 { + opp-hz = /bits/ 64 <720000000>; + opp-microvolt = <1260000 1234800 1285200>; + opp-supported-hw = <0x01 0xFFFF>; + }; + + oppturbo@800000000 { + opp-hz = /bits/ 64 <800000000>; + opp-microvolt = <1260000 1234800 1285200>; + opp-supported-hw = <0x06 0x0100>; + }; + + oppnitro@1000000000 { + opp-hz = /bits/ 64 <1000000000>; + opp-microvolt = <1325000 1298500 1351500>; + opp-supported-hw = <0x04 0x0200>; + }; +}; diff --git b/Documentation/devicetree/bindings/misc/bone_capemgr.txt b/Documentation/devicetree/bindings/misc/bone_capemgr.txt new file mode 100644 index 000000000..7e4fbc982 --- /dev/null +++ b/Documentation/devicetree/bindings/misc/bone_capemgr.txt @@ -0,0 +1,111 @@ +* Beaglebone cape manager driver + +Required properties: +- compatible: "ti,bone-capemgr" +- eeprom: phandle to the EEPROM baseboard. + The EEPROM framework interface is use to obtain the data. + +Required children nodes: + +- baseboardmaps: Contains nodes, which each of the them defines a mapping from + the baseboard EEPROM board-name ID to a DT friendly compatible + string. + + - board-name: The baseboard EEPROM board name, i.e. A335BONE for the + original beaglebone white. + - compatible-name: The DT friendly compatible string to be used for matching + compatible capes, i.e. "ti,beaglebone" + + + - nvmem-cells: Defines the phandles of the nvmem cells of the baseboard and the + slots. + - nvmem-cells: Defines the names of the nvmem cells. Required to have at + least a baseboard cell name. + + - #slots: Defines how many slots are there. + +- Example of a beaglebone cape-manager: + +bone_capemgr { + compatible = "ti,bone-capemgr"; + status = "okay"; + + nvmem-cell = <&baseboard_data + &cape0_data &cape1_data &cape2_data &cape3_data>; + nvmem-cell-names = "baseboard", "slot0", "slot1", "slot2", "slot3"; + + #slots = <4>; + + /* map board revisions to compatible definitions */ + baseboardmaps { + baseboard_beaglebone: board@0 { + board-name = "A335BONE"; + compatible-name = "ti,beaglebone"; + }; + + baseboard_beaglebone_black: board@1 { + board-name = "A335BNLT"; + compatible-name = "ti,beaglebone-black"; + }; + }; +}; + +The format of the cape to be loaded is in a standard overlay format with +the following root properties that are interpreted by the cape manager: + +Required properties: + - compatible: Should be compatible to the baseboard according to the + baseboard map value, i.e. "ti,beaglebone". + - part-numer: Should contain the part-number as stored in the EEPROM. + - version: Should contain a list of all the version that are supported + by the single cape dtbo, i.e. "00A1". + +Optional properties: + - exclusive-use: A string list which state the resources this cape requires. + No processing or matching to anything regarding the internal + kernel state is performed; it's purpose is to guard against + conflicts with other capes. + - priority: A priority to be assigned when loading a cape. A lower value + has higher priority. The purpose of the priority is to control + which cape is loaded first in case of a conflict. + +- Example of a serial cape: + +/dts-v1/; +/plugin/; +/ { + compatible = "ti,beaglebone", "ti,beaglebone-black"; + + /* identification */ + part-number = "BB-BONE-SERL-03"; + version = "00A1"; + + /* state the resources this cape uses */ + exclusive-use = + /* the pin header uses */ + "P9.21", /* uart2_txd */ + "P9.22", /* uart2_rxd */ + /* the hardware ip uses */ + "uart2"; + + fragment@0 { + target = <&am33xx_pinmux>; + __overlay__ { + bb_uart2_pins: pinmux_bb_uart2_pins { + pinctrl-single,pins = < + 0x150 0x21 /* spi0_sclk.uart2_rxd | MODE1 */ + 0x154 0x01 /* spi0_d0.uart2_txd | MODE1 */ + >; + }; + }; + }; + + fragment@1 { + target = <&uart2>; + __overlay__ { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&bb_uart2_pins>; + }; + }; +}; diff --git b/Documentation/devicetree/bindings/net/allwinner,sun8i-emac.txt b/Documentation/devicetree/bindings/net/allwinner,sun8i-emac.txt new file mode 100644 index 000000000..4bf4e5336 --- /dev/null +++ b/Documentation/devicetree/bindings/net/allwinner,sun8i-emac.txt @@ -0,0 +1,65 @@ +* Allwinner sun8i EMAC ethernet controller + +Required properties: +- compatible: "allwinner,sun8i-a83t-emac", "allwinner,sun8i-h3-emac", + or "allwinner,sun50i-a64-emac" +- reg: address and length of the register sets for the device. +- reg-names: should be "emac" and "syscon", matching the register sets +- interrupts: interrupt for the device +- clocks: A phandle to the reference clock for this device +- clock-names: should be "ahb" +- resets: A phandle to the reset control for this device +- reset-names: should be "ahb" +- phy-mode: See ethernet.txt +- phy or phy-handle: See ethernet.txt +- #address-cells: shall be 1 +- #size-cells: shall be 0 + +"allwinner,sun8i-h3-emac" also requires: +- clocks: an extra phandle to the reference clock for the EPHY +- clock-names: an extra "ephy" entry matching the clocks property +- resets: an extra phandle to the reset control for the EPHY +- resets-names: an extra "ephy" entry matching the resets property + +See ethernet.txt in the same directory for generic bindings for ethernet +controllers. + +The device node referenced by "phy" or "phy-handle" should be a child node +of this node. See phy.txt for the generic PHY bindings. + +Optional properties: +- phy-supply: phandle to a regulator if the PHY needs one +- phy-io-supply: phandle to a regulator if the PHY needs a another one for I/O. + This is sometimes found with RGMII PHYs, which use a second + regulator for the lower I/O voltage. +- allwinner,tx-delay: The setting of the TX clock delay chain +- allwinner,rx-delay: The setting of the RX clock delay chain + +The TX/RX clock delay chain settings are board specific. + +Optional properties for "allwinner,sun8i-h3-emac": +- allwinner,use-internal-phy: Use the H3 SoC's internal E(thernet) PHY +- allwinner,leds-active-low: EPHY LEDs are active low + +When the internal PHY is requested, the implementation shall configure the +internal PHY to use the address specified in the child PHY node. + +Example: + +emac: ethernet@01c0b000 { + compatible = "allwinner,sun8i-h3-emac"; + reg = <0x01c0b000 0x104>, <0x01c00030 0x4>; + reg-names = "emac", "syscon"; + interrupts = ; + clocks = <&bus_gates 17>, <&bus_gates 128>; + clock-names = "ahb", "ephy"; + resets = <&ahb_rst 17>, <&ahb_rst 66>; + reset-names = "ahb", "ephy"; + phy = <&phy1>; + allwinner,use-internal-phy; + allwinner,leds-active-low; + + phy1: ethernet-phy@1 { + reg = <1>; + }; +}; diff --git a/Documentation/devicetree/bindings/opp/opp.txt b/Documentation/devicetree/bindings/opp/opp.txt index ee91cbdd9..9f5ca4457 100644 --- a/Documentation/devicetree/bindings/opp/opp.txt +++ b/Documentation/devicetree/bindings/opp/opp.txt @@ -86,8 +86,14 @@ Optional properties: Single entry is for target voltage and three entries are for voltages. - Entries for multiple regulators must be present in the same order as - regulators are specified in device's DT node. + Entries for multiple regulators shall be provided in the same field separated + by angular brackets <>. The OPP binding doesn't provide any provisions to + relate the values to their power supplies or the order in which the supplies + need to be configured and that is left for the implementation specific + binding. + + Entries for all regulators shall be of the same size, i.e. either all use a + single value or triplets. - opp-microvolt-: Named opp-microvolt property. This is exactly similar to the above opp-microvolt property, but allows multiple voltage ranges to be @@ -104,10 +110,13 @@ Optional properties: Should only be set if opp-microvolt is set for the OPP. - Entries for multiple regulators must be present in the same order as - regulators are specified in device's DT node. If this property isn't required - for few regulators, then this should be marked as zero for them. If it isn't - required for any regulator, then this property need not be present. + Entries for multiple regulators shall be provided in the same field separated + by angular brackets <>. If current values aren't required for a regulator, + then it shall be filled with 0. If current values aren't required for any of + the regulators, then this field is not required. The OPP binding doesn't + provide any provisions to relate the values to their power supplies or the + order in which the supplies need to be configured and that is left for the + implementation specific binding. - opp-microamp-: Named opp-microamp property. Similar to opp-microvolt- property, but for microamp instead. @@ -386,10 +395,12 @@ Example 4: Handling multiple regulators / { cpus { cpu@0 { - compatible = "arm,cortex-a7"; + compatible = "vendor,cpu-type"; ... - cpu-supply = <&cpu_supply0>, <&cpu_supply1>, <&cpu_supply2>; + vcc0-supply = <&cpu_supply0>; + vcc1-supply = <&cpu_supply1>; + vcc2-supply = <&cpu_supply2>; operating-points-v2 = <&cpu0_opp_table>; }; }; diff --git b/Documentation/devicetree/bindings/pinctrl/ti,iodelay-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/ti,iodelay-pinctrl.txt new file mode 100644 index 000000000..e12f4e5a3 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/ti,iodelay-pinctrl.txt @@ -0,0 +1,86 @@ +Texas Instruments I/O Delay module configuration pinctrl definition + +Used in conjunction with Documentation/devicetree/bindings/pinctrl/ti,omap-pinctrl.txt + +Required Properties: +- compatible: Should be: + "ti,dra7-iodelay" - I/O delay configuration for DRA7 +- reg - must be the register address range of IODelay module +- #address-cells = <1>; +- #size-cells = <0>; + +Important note: Use of "ti,dra7-iodelay" compatible definition need to be +carefully evaluated due to the expectation of glitch during configuration. + +Example: + +dra7_iodelay_core: padconf@4844a000 { + compatible = "ti,dra7-iodelay"; + reg = <0x4844a000 0x0d1c>; + #address-cells = <1>; + #size-cells = <0>; +}; + +Configuration definition follows similar model as the pinctrl-single: +The groups of pin configuration are defined under "pinctrl-single,pins" + +&dra7_iodelay_core { + mmc2_iodelay_3v3_conf: mmc2_iodelay_3v3_conf { + pinctrl-single,pins = < + 0x18c (A_DELAY(0) | G_DELAY(120)) /* CFG_GPMC_A19_IN */ + 0x1a4 (A_DELAY(265) | G_DELAY(360)) /* CFG_GPMC_A20_IN */ + 0x1b0 (A_DELAY(0) | G_DELAY(120)) /* CFG_GPMC_A21_IN */ + 0x1bc (A_DELAY(0) | G_DELAY(120)) /* CFG_GPMC_A22_IN */ + 0x1c8 (A_DELAY(287) | G_DELAY(420)) /* CFG_GPMC_A23_IN */ + 0x1d4 (A_DELAY(144) | G_DELAY(240)) /* CFG_GPMC_A24_IN */ + 0x1e0 (A_DELAY(0) | G_DELAY(0)) /* CFG_GPMC_A25_IN */ + 0x1ec (A_DELAY(120) | G_DELAY(0)) /* CFG_GPMC_A26_IN */ + 0x1f8 (A_DELAY(120) | G_DELAY(180)) /* CFG_GPMC_A27_IN */ + 0x360 (A_DELAY(0) | G_DELAY(0)) /* CFG_GPMC_CS1_IN */ + >; + }; +}; + +Usage in conjunction with pinctrl single: + +For a complete description of the pins both the regular muxing as well as the +iodelay configuration is necessary. For example: + +&dra7_pmx_core { + mmc2_pins_default: mmc2_pins_default { + pinctrl-single,pins = < + 0x9c (PIN_INPUT_PULLUP | MANUAL_MODE | MUX_MODE1) /* gpmc_a23.mmc2_clk */ + 0xb0 (PIN_INPUT_PULLUP | MANUAL_MODE | MUX_MODE1) /* gpmc_cs1.mmc2_cmd */ + 0xa0 (PIN_INPUT_PULLUP | MANUAL_MODE | MUX_MODE1) /* gpmc_a24.mmc2_dat0 */ + 0xa4 (PIN_INPUT_PULLUP | MANUAL_MODE | MUX_MODE1) /* gpmc_a25.mmc2_dat1 */ + 0xa8 (PIN_INPUT_PULLUP | MANUAL_MODE | MUX_MODE1) /* gpmc_a26.mmc2_dat2 */ + 0xac (PIN_INPUT_PULLUP | MANUAL_MODE | MUX_MODE1) /* gpmc_a27.mmc2_dat3 */ + 0x8c (PIN_INPUT_PULLUP | MANUAL_MODE | MUX_MODE1) /* gpmc_a19.mmc2_dat4 */ + 0x90 (PIN_INPUT_PULLUP | MANUAL_MODE | MUX_MODE1) /* gpmc_a20.mmc2_dat5 */ + 0x94 (PIN_INPUT_PULLUP | MANUAL_MODE | MUX_MODE1) /* gpmc_a21.mmc2_dat6 */ + 0x98 (PIN_INPUT_PULLUP | MANUAL_MODE | MUX_MODE1) /* gpmc_a22.mmc2_dat7 */ + >; + }; +}; + +&dra7_iodelay_core { + mmc2_iodelay_3v3_conf: mmc2_iodelay_3v3_conf { + pinctrl-single,pins = < + 0x18c (A_DELAY(0) | G_DELAY(120)) /* CFG_GPMC_A19_IN */ + 0x1a4 (A_DELAY(265) | G_DELAY(360)) /* CFG_GPMC_A20_IN */ + 0x1b0 (A_DELAY(0) | G_DELAY(120)) /* CFG_GPMC_A21_IN */ + 0x1bc (A_DELAY(0) | G_DELAY(120)) /* CFG_GPMC_A22_IN */ + 0x1c8 (A_DELAY(287) | G_DELAY(420)) /* CFG_GPMC_A23_IN */ + 0x1d4 (A_DELAY(144) | G_DELAY(240)) /* CFG_GPMC_A24_IN */ + 0x1e0 (A_DELAY(0) | G_DELAY(0)) /* CFG_GPMC_A25_IN */ + 0x1ec (A_DELAY(120) | G_DELAY(0)) /* CFG_GPMC_A26_IN */ + 0x1f8 (A_DELAY(120) | G_DELAY(180)) /* CFG_GPMC_A27_IN */ + 0x360 (A_DELAY(0) | G_DELAY(0)) /* CFG_GPMC_CS1_IN */ + >; + }; +}; + +&mmc2 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc2_pins_default &mmc2_iodelay_3v3_conf>; +}; diff --git b/Documentation/devicetree/bindings/power/pwrseq/pwrseq-generic.txt b/Documentation/devicetree/bindings/power/pwrseq/pwrseq-generic.txt new file mode 100644 index 000000000..ebf0d477b --- /dev/null +++ b/Documentation/devicetree/bindings/power/pwrseq/pwrseq-generic.txt @@ -0,0 +1,48 @@ +The generic power sequence library + +Some hard-wired devices (eg USB/MMC) need to do power sequence before +the device can be enumerated on the bus, the typical power sequence +like: enable USB PHY clock, toggle reset pin, etc. But current +Linux device driver lacks of such code to do it, it may cause some +hard-wired devices works abnormal or can't be recognized by +controller at all. The power sequence will be done before this device +can be found at the bus. + +The power sequence properties is under the device node. + +Optional properties: +- clocks: the input clocks for device. +- reset-gpios: Should specify the GPIO for reset. +- reset-duration-us: the duration in microsecond for assert reset signal. + +Below is the example of USB power sequence properties on USB device +nodes which have two level USB hubs. + +&usbotg1 { + vbus-supply = <®_usb_otg1_vbus>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usb_otg1_id>; + status = "okay"; + + #address-cells = <1>; + #size-cells = <0>; + genesys: hub@1 { + compatible = "usb5e3,608"; + reg = <1>; + + clocks = <&clks IMX6SX_CLK_CKO>; + reset-gpios = <&gpio4 5 GPIO_ACTIVE_LOW>; /* hub reset pin */ + reset-duration-us = <10>; + + #address-cells = <1>; + #size-cells = <0>; + asix: ethernet@1 { + compatible = "usbb95,1708"; + reg = <1>; + + clocks = <&clks IMX6SX_CLK_IPG>; + reset-gpios = <&gpio4 6 GPIO_ACTIVE_LOW>; /* ethernet_rst */ + reset-duration-us = <15>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/usb/usb-device.txt b/Documentation/devicetree/bindings/usb/usb-device.txt index 1c35e7b66..3661dd261 100644 --- a/Documentation/devicetree/bindings/usb/usb-device.txt +++ b/Documentation/devicetree/bindings/usb/usb-device.txt @@ -13,6 +13,10 @@ Required properties: - reg: the port number which this device is connecting to, the range is 1-31. +Optional properties: +power sequence properties, see +Documentation/devicetree/bindings/power/pwrseq/pwrseq-generic.txt for detail + Example: &usb1 { @@ -21,8 +25,12 @@ Example: #address-cells = <1>; #size-cells = <0>; - hub: genesys@1 { + genesys: hub@1 { compatible = "usb5e3,608"; reg = <1>; + + clocks = <&clks IMX6SX_CLK_CKO>; + reset-gpios = <&gpio4 5 GPIO_ACTIVE_LOW>; /* hub reset pin */ + reset-duration-us = <10>; }; } diff --git b/Documentation/devicetree/configfs-overlays.txt b/Documentation/devicetree/configfs-overlays.txt new file mode 100644 index 000000000..5fa43e064 --- /dev/null +++ b/Documentation/devicetree/configfs-overlays.txt @@ -0,0 +1,31 @@ +Howto use the configfs overlay interface. + +A device-tree configfs entry is created in /config/device-tree/overlays +and and it is manipulated using standard file system I/O. +Note that this is a debug level interface, for use by developers and +not necessarily something accessed by normal users due to the +security implications of having direct access to the kernel's device tree. + +* To create an overlay you mkdir the directory: + + # mkdir /config/device-tree/overlays/foo + +* Either you echo the overlay firmware file to the path property file. + + # echo foo.dtbo >/config/device-tree/overlays/foo/path + +* Or you cat the contents of the overlay to the dtbo file + + # cat foo.dtbo >/config/device-tree/overlays/foo/dtbo + +The overlay file will be applied, and devices will be created/destroyed +as required. + +To remove it simply rmdir the directory. + + # rmdir /config/device-tree/overlays/foo + +The rationalle of the dual interface (firmware & direct copy) is that each is +better suited to different use patterns. The firmware interface is what's +intended to be used by hardware managers in the kernel, while the copy interface +make sense for developers (since it avoids problems with namespaces). diff --git a/Documentation/devicetree/overlay-notes.txt b/Documentation/devicetree/overlay-notes.txt index d418a6ce9..3e8df3093 100644 --- a/Documentation/devicetree/overlay-notes.txt +++ b/Documentation/devicetree/overlay-notes.txt @@ -100,6 +100,14 @@ Finally, if you need to remove all overlays in one-go, just call of_overlay_destroy_all() which will remove every single one in the correct order. +If your board has multiple slots/places where a single overlay can work +and each slot is defined by a node, you can use the +of_overlay_create_target_index() method to select the target. + +For overlays on probeable busses, use the of_overlay_create_target_root() method +in which you supply a device node as a target root, and which all target +references in the overlay are performed relative to that node. + Overlay DTS Format ------------------ @@ -110,9 +118,11 @@ The DTS of an overlay should have the following format: fragment@0 { /* first child node */ - target=; /* phandle target of the overlay */ + /* phandle target of the overlay */ + target= [, , ...]; or - target-path="/path"; /* target path of the overlay */ + /* target path of the overlay */ + target-path="/path" [ , "/path", ...]; __overlay__ { property-a; /* add property-a to the target */ @@ -131,3 +141,11 @@ Using the non-phandle based target method allows one to use a base DT which does not contain a __symbols__ node, i.e. it was not compiled with the -@ option. The __symbols__ node is only required for the target= method, since it contains the information required to map from a phandle to a tree location. + +Using a target index requires the use of a selector target on the call to +of_overlay_create_target_index(). I.e. passing an index of 0 will select the +target in the foo node, an index of 1 the bar node, etc. + +Note that when using the target root create method all target references must +lie under the target root node. I.e. the overlay is not allowed to 'break' out +of the root. diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt index 37babf91f..e7d6ae47c 100644 --- a/Documentation/kernel-parameters.txt +++ b/Documentation/kernel-parameters.txt @@ -121,6 +121,7 @@ parameter is applicable: NET Appropriate network support is enabled. NUMA NUMA support is enabled. NFS Appropriate NFS support is enabled. + OF Open Firmware support (device tree) is enabled. OSS OSS sound support is enabled. PV_OPS A paravirtualized kernel is enabled. PARIDE The ParIDE (parallel port IDE) subsystem is enabled. @@ -2858,6 +2859,8 @@ bytes respectively. Such letter suffixes can also be entirely omitted. This can be set from sysctl after boot. See Documentation/sysctl/vm.txt for details. + of_overlay_disable [OF] Disable device tree overlays at boot time. + ohci1394_dma=early [HW] enable debugging via the ohci1394 driver. See Documentation/debugging-via-ohci1394.txt for more info. diff --git b/Documentation/misc-devices/bone_capemgr.txt b/Documentation/misc-devices/bone_capemgr.txt new file mode 100644 index 000000000..2a8c766b4 --- /dev/null +++ b/Documentation/misc-devices/bone_capemgr.txt @@ -0,0 +1,63 @@ +--------------------------- + Beaglebone Cape-Manager +--------------------------- + +The beaglebone cape manager driver allows the automatic use of external +peripheral capes to be automatically supported by Linux without any manual +setup required by the user. + +Each beaglebone cape should contain an EEPROM that describes +it in a fixed I2C address on the i2c2 bus of the baseboard. +The format of the EEPROM is defined in the beaglebone reference +manual at: +http://beagleboard.org/static/beaglebone/latest/Docs/Hardware/BONE_SRM.pdf + +Reading the part number and revision information the manager +requests a firmware file formatted as a device tree overlay blob. + +Applying the overlay the devices are instantiated and the cape is +ready to be used. + +For instance if the part-number is BB-BONE-SERL-03 and the version is 00A1 +the firmware file requested will be BB-BONE-SERL-03-00A1-00A1.dtbo +It will be located by the in-kernel firmware +loader in the usual place, i.e. /lib/firmware/`uname -r`, /lib/firmware etc. + +The driver supports the following parameters (either as part of the kernel +command line or supplied at module insertion time). + +disable_partno: A comma delimited list of PART-NUMBER[:REV] of + disabled capes. +enable_partno: A comma delimited list of PART-NUMBER[:REV[:PRIO]] of + enabled capes. +boot_scan_period: The boot scan period in ms. When the cape manager is built-in + the kernel image, the firmware loader cannot find the files + before the rootfs is mounted. This parameter controls the + period with which the boot state is checked in that case. + +There's a sysfs control interface which is defined at the ABI documentation +area. + +Theory of operation: +-------------------- + +On driver probe the I2C EEPROM of the baseboard is read and information about +the current baseboard is retrieved. This information includes the mapping from +baseboard board name to DT friendly compatible string. I.e. the "A335BONE" board +name from EEPROM is mapped to the "ti,beaglebone" compatible string which should +be present in the dtbo to be loaded. + +Afterwards the EEPROMs declared in each slot are probed, and the EEPROMs found +are decoded keeping track the cape part-number and version data. + +Using the part-number and version a firmware file is requested (the firmware +file requested is -.dtbo). + +The dtbo is unflattend and the resulting device tree is matched against a +compatible baseboard, and in case of multiple parallel loading capes the +priorities defined are honored. That means that when there are multiple capes +being loaded in parallel the ones with the lowest priority number are loaded +first. + +Applying the device tree overlay makes the cape operational, as if it was part +of the kernel's booting device tree. diff --git a/Documentation/printk-formats.txt b/Documentation/printk-formats.txt index 596294994..d1ba882d1 100644 --- a/Documentation/printk-formats.txt +++ b/Documentation/printk-formats.txt @@ -324,10 +324,49 @@ Network device features: Passed by reference. +Command from struct task_struct + + %pT ls + + For printing executable name excluding path from struct + task_struct. + + Passed by reference. + +Device tree nodes: + + %pO[fnpPcCFr] + + For printing device tree nodes. The optional arguments are: + f device node full_name + n device node name + p device node phandle + P device node path spec (name + @unit) + F device node flags + c major compatible string + C full compatible string + r node reference count + Without any arguments prints full_name (same as %pOf) + The separator when using multiple arguments is '|' + + Examples: + + %pO /foo/bar@0 - Node full name + %pOf /foo/bar@0 - Same as above + %pOfp /foo/bar@0|10 - Node full name + phandle + %pOfcF /foo/bar@0|foo,device|--P- - Node full name + + major compatible string + + node flags + D - dynamic + d - detached + P - Populated + B - Populated bus + + Passed by reference + If you add other %p extensions, please extend lib/test_printf.c with one or more test cases, if at all feasible. - Thank you for your cooperation and attention. diff --git a/MAINTAINERS b/MAINTAINERS index 63cefa623..d49fd4682 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -597,6 +597,12 @@ S: Maintained F: Documentation/i2c/busses/i2c-ali1563 F: drivers/i2c/busses/i2c-ali1563.c +ALLWINNER SUN8I-EMAC ETHERNET DRIVER +M: Corentin Labbe +L: netdev@vger.kernel.org +S: Maintained +F: drivers/net/ethernet/allwinner/sun8i-emac.c + ALLWINNER SECURITY SYSTEM M: Corentin Labbe L: linux-crypto@vger.kernel.org @@ -2401,6 +2407,14 @@ W: https://linuxtv.org S: Supported F: drivers/media/platform/sti/bdisp +BEAGLEBONE CAPEMANAGER +M: Pantelis Antoniou +S: Maintained +F: drivers/misc/beaglebone-capemgr.c +F: Documentation/misc-devices/bone_capemgr.txt +F: Documentation/devicetree/bindings/misc/bone_capemgr.txt +F: Documentation/ABI/testing/sysfs-devices-platform-bone_capemgr + BEFS FILE SYSTEM M: Luis de Bethencourt M: Salah Triki @@ -9635,6 +9649,15 @@ F: include/linux/pm_* F: include/linux/powercap.h F: drivers/powercap/ +POWER SEQUENCE LIBRARY +M: Peter Chen +T: git git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb.git +L: linux-pm@vger.kernel.org +S: Maintained +F: Documentation/devicetree/bindings/power/pwrseq/ +F: drivers/power/pwrseq/ +F: include/linux/power/pwrseq.h/ + POWER SUPPLY CLASS/SUBSYSTEM and DRIVERS M: Sebastian Reichel L: linux-pm@vger.kernel.org diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig index b5d529fdf..ced2e08a9 100644 --- a/arch/arm/Kconfig +++ b/arch/arm/Kconfig @@ -1496,8 +1496,7 @@ source kernel/Kconfig.preempt config HZ_FIXED int - default 200 if ARCH_EBSA110 || ARCH_S3C24XX || \ - ARCH_S5PV210 || ARCH_EXYNOS4 + default 200 if ARCH_EBSA110 default 128 if SOC_AT91RM9200 default 0 diff --git a/arch/arm/Makefile b/arch/arm/Makefile index 6be9ee148..6deeab7c8 100644 --- a/arch/arm/Makefile +++ b/arch/arm/Makefile @@ -13,7 +13,12 @@ # Ensure linker flags are correct LDFLAGS := -LDFLAGS_vmlinux :=-p --no-undefined -X --pic-veneer +GCCVERSIONISGTE5 := $(shell expr `$(HOSTCC) -dumpversion | cut -f1 -d.` \>= 5) +ifeq "$(GCCVERSIONISGTE5)" "1" +LDFLAGS_vmlinux :=-p --no-undefined -X +else +LDFLAGS_vmlinux :=-p --no-undefined -X --pic-veneer +endif ifeq ($(CONFIG_CPU_ENDIAN_BE8),y) LDFLAGS_vmlinux += --be8 LDFLAGS_MODULE += --be8 diff --git a/arch/arm/boot/Makefile b/arch/arm/boot/Makefile index 50f8d1be7..2c30c4491 100644 --- a/arch/arm/boot/Makefile +++ b/arch/arm/boot/Makefile @@ -29,6 +29,10 @@ export ZRELADDR INITRD_PHYS PARAMS_PHYS targets := Image zImage xipImage bootpImage uImage +ifeq ($(CONFIG_OF_OVERLAY),y) +DTC_FLAGS += -@ +endif + ifeq ($(CONFIG_XIP_KERNEL),y) $(obj)/xipImage: vmlinux FORCE diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index c558ba75c..f3283015d 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -1,11 +1,17 @@ ifeq ($(CONFIG_OF),y) +ifeq ($(CONFIG_OF_OVERLAY),y) +DTC_FLAGS += -@ +endif + dtb-$(CONFIG_ARCH_ALPINE) += \ alpine-db.dtb dtb-$(CONFIG_MACH_ARTPEC6) += \ artpec6-devboard.dtb + dtb-$(CONFIG_MACH_ASM9260) += \ alphascale-asm9260-devkit.dtb + # Keep at91 dtb files sorted alphabetically for each SoC dtb-$(CONFIG_SOC_AT91RM9200) += \ at91rm9200ek.dtb \ @@ -155,6 +161,7 @@ dtb-$(CONFIG_ARCH_EXYNOS5) += \ exynos5420-arndale-octa.dtb \ exynos5420-peach-pit.dtb \ exynos5420-smdk5420.dtb \ + exynos5422-artik10-eval.dtb \ exynos5422-odroidxu3.dtb \ exynos5422-odroidxu3-lite.dtb \ exynos5422-odroidxu4.dtb \ @@ -366,6 +373,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \ imx6q-b650v3.dtb \ imx6q-b850v3.dtb \ imx6q-cm-fx6.dtb \ + imx6q-ccimx6sbc.dtb \ imx6q-cubox-i.dtb \ imx6q-dfi-fs700-m60.dtb \ imx6q-dmo-edmqmx6.dtb \ @@ -419,6 +427,7 @@ dtb-$(CONFIG_SOC_IMX6SX) += \ imx6sx-sdb.dtb dtb-$(CONFIG_SOC_IMX6UL) += \ imx6ul-14x14-evk.dtb \ + imx6ul-14x14-evk-ism43362-b81-evb.dtb \ imx6ul-geam-kit.dtb \ imx6ul-pico-hobbit.dtb \ imx6ul-tx6ul-0010.dtb \ @@ -547,6 +556,27 @@ dtb-$(CONFIG_SOC_AM33XX) += \ am335x-base0033.dtb \ am335x-bone.dtb \ am335x-boneblack.dtb \ + am335x-sancloud-bbe.dtb \ + am335x-boneblack-wireless-roboticscape.dtb \ + am335x-boneblack-roboticscape.dtb \ + am335x-boneblue.dtb \ + am335x-boneblack-wireless-emmc-overlay.dtb \ + am335x-boneblack-wireless.dtb \ + am335x-bonegreen-wireless.dtb \ + am335x-boneblack-audio.dtb \ + am335x-boneblack-bbb-exp-r.dtb \ + am335x-boneblack-bbb-exp-c.dtb \ + am335x-boneblack-bbbmini.dtb \ + am335x-boneblack-wl1835mod.dtb \ + am335x-boneblack-cape-bone-argus.dtb \ + am335x-bone-cape-bone-argus.dtb \ + am335x-olimex-som.dtb \ + am335x-abbbi.dtb \ + am335x-bonegreen-overlay.dtb \ + am335x-boneblack-overlay.dtb \ + am335x-boneblack-nhdmi-overlay.dtb \ + am335x-boneblack-hdmi-overlay.dtb \ + am335x-boneblack-emmc-overlay.dtb \ am335x-bonegreen.dtb \ am335x-chiliboard.dtb \ am335x-cm-t335.dtb \ @@ -566,6 +596,7 @@ dtb-$(CONFIG_ARCH_OMAP4) += \ omap4-panda.dtb \ omap4-panda-a4.dtb \ omap4-panda-es.dtb \ + omap4-panda-es-b3.dtb \ omap4-sdp.dtb \ omap4-sdp-es23plus.dtb \ omap4-var-dvk-om44.dtb \ diff --git b/arch/arm/boot/dts/am335x-abbbi.dts b/arch/arm/boot/dts/am335x-abbbi.dts new file mode 100644 index 000000000..43efeadea --- /dev/null +++ b/arch/arm/boot/dts/am335x-abbbi.dts @@ -0,0 +1,163 @@ +/* + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ + * Copyright 2015 Konsulko Group + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +/dts-v1/; + +#include "am33xx.dtsi" +#include "am335x-bone-common.dtsi" + + +/ { + model = "Arrow BeagleBone Black Industrial"; + compatible = "arrow,am335x-abbbi", "ti,am335x-bone", "ti,am33xx"; +}; + +&ldo3_reg { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; +}; + +&mmc1 { + vmmc-supply = <&vmmcsd_fixed>; +}; + +&mmc2 { + vmmc-supply = <&vmmcsd_fixed>; + pinctrl-names = "default"; + pinctrl-0 = <&emmc_pins>; + bus-width = <8>; + status = "okay"; +}; + +&am33xx_pinmux { + adi_hdmi_bbbi_pins: adi_hdmi_bbbi_pins { + pinctrl-single,pins = < + AM33XX_IOPAD(0x9b0, PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* xdma_event_intr0 */ + AM33XX_IOPAD(0x8a0, PIN_OUTPUT | MUX_MODE0) /* lcd_data0.lcd_data0 */ + AM33XX_IOPAD(0x8a4, PIN_OUTPUT | MUX_MODE0) /* lcd_data1.lcd_data1 */ + AM33XX_IOPAD(0x8a8, PIN_OUTPUT | MUX_MODE0) /* lcd_data2.lcd_data2 */ + AM33XX_IOPAD(0x8ac, PIN_OUTPUT | MUX_MODE0) /* lcd_data3.lcd_data3 */ + AM33XX_IOPAD(0x8b0, PIN_OUTPUT | MUX_MODE0) /* lcd_data4.lcd_data4 */ + AM33XX_IOPAD(0x8b4, PIN_OUTPUT | MUX_MODE0) /* lcd_data5.lcd_data5 */ + AM33XX_IOPAD(0x8b8, PIN_OUTPUT | MUX_MODE0) /* lcd_data6.lcd_data6 */ + AM33XX_IOPAD(0x8bc, PIN_OUTPUT | MUX_MODE0) /* lcd_data7.lcd_data7 */ + AM33XX_IOPAD(0x8c0, PIN_OUTPUT | MUX_MODE0) /* lcd_data8.lcd_data8 */ + AM33XX_IOPAD(0x8c4, PIN_OUTPUT | MUX_MODE0) /* lcd_data9.lcd_data9 */ + AM33XX_IOPAD(0x8c8, PIN_OUTPUT | MUX_MODE0) /* lcd_data10.lcd_data10 */ + AM33XX_IOPAD(0x8cc, PIN_OUTPUT | MUX_MODE0) /* lcd_data11.lcd_data11 */ + AM33XX_IOPAD(0x8d0, PIN_OUTPUT | MUX_MODE0) /* lcd_data12.lcd_data12 */ + AM33XX_IOPAD(0x8d4, PIN_OUTPUT | MUX_MODE0) /* lcd_data13.lcd_data13 */ + AM33XX_IOPAD(0x8d8, PIN_OUTPUT | MUX_MODE0) /* lcd_data14.lcd_data14 */ + AM33XX_IOPAD(0x8dc, PIN_OUTPUT | MUX_MODE0) /* lcd_data15.lcd_data15 */ + AM33XX_IOPAD(0x8e0, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* lcd_vsync.lcd_vsync */ + AM33XX_IOPAD(0x8e4, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* lcd_hsync.lcd_hsync */ + AM33XX_IOPAD(0x8e8, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* lcd_pclk.lcd_pclk */ + AM33XX_IOPAD(0x8ec, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* lcd_ac_bias_en.lcd_ac_bias_en */ + >; + }; + adi_hdmi_bbbi_off_pins: adi_hdmi_bbbi_off_pins { + pinctrl-single,pins = < + AM33XX_IOPAD(0x9b0, PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* xdma_event_intr0 */ + >; + }; + + mcasp0_pins: mcasp0_pins { + pinctrl-single,pins = < + 0x1ac (PIN_INPUT_PULLUP | MUX_MODE0) /* mcasp0_ahclkx.mcasp0_ahclkx */ + 0x19c (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mcasp0_ahclkr.mcasp0_axr2 */ + 0x194 (PIN_OUTPUT_PULLUP | MUX_MODE0) /* mcasp0_fsx.mcasp0_fsx */ + 0x190 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mcasp0_aclkx.mcasp0_aclkx */ + 0x06c (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a11.GPIO1_27 */ + >; + }; + + mcasp0_pins_sleep: mcasp0_pins_sleep { + pinctrl-single,pins = < + 0x1ac (PIN_INPUT_PULLDOWN | MUX_MODE7) /* mcasp0_ahclkx.mcasp0_ahclkx */ + 0x19c (PIN_INPUT_PULLDOWN | MUX_MODE7) /* mcasp0_ahclkr.mcasp0_axr2 */ + 0x194 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* mcasp0_fsx.mcasp0_fsx */ + 0x190 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* mcasp0_aclkx.mcasp0_aclkx */ + 0x06c (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_a11.GPIO1_27 */ + >; + }; +}; + +&lcdc { + status = "okay"; + port { + lcdc_0: endpoint@0 { + remote-endpoint = <&hdmi_0>; + }; + }; +}; + +&i2c0 { + adv7511w { + compatible = "adi,adv7511w"; + reg = <0x39>; + pinctrl-names = "default", "off"; + pinctrl-0 = <&adi_hdmi_bbbi_pins>; + pinctrl-1 = <&adi_hdmi_bbbi_off_pins>; + + port { + hdmi_0: endpoint@0 { + remote-endpoint = <&lcdc_0>; + }; + }; + }; +}; + +&mcasp0 { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&mcasp0_pins>; + pinctrl-1 = <&mcasp0_pins_sleep>; + status = "okay"; + op-mode = <0>; /* MCASP_IIS_MODE */ + tdm-slots = <2>; + serial-dir = < /* 0: INACTIVE, 1: TX, 2: RX */ + 0 0 1 0 + >; + tx-num-evt = <1>; + rx-num-evt = <1>; +}; + +/ { + clk_mcasp0_fixed: clk_mcasp0_fixed { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <24576000>; + }; + + clk_mcasp0: clk_mcasp0 { + #clock-cells = <0>; + compatible = "gpio-gate-clock"; + clocks = <&clk_mcasp0_fixed>; + enable-gpios = <&gpio1 27 0>; /* BeagleBone Black Clk enable on GPIO1_27 */ + }; + + hdmi_audio: hdmi_audio@0 { + compatible = "linux,hdmi-audio"; + status = "okay"; + }; + + sound { + compatible = "ti,beaglebone-black-audio"; + ti,model = "TI BeagleBone Black"; + ti,audio-codec = <&hdmi_audio>; + ti,mcasp-controller = <&mcasp0>; + ti,audio-routing = + "HDMI Out", "TX"; + clocks = <&clk_mcasp0>; + clock-names = "mclk"; + }; +}; + +&rtc { + system-power-controller; +}; diff --git b/arch/arm/boot/dts/am335x-bone-argus.dtsi b/arch/arm/boot/dts/am335x-bone-argus.dtsi new file mode 100644 index 000000000..21afad398 --- /dev/null +++ b/arch/arm/boot/dts/am335x-bone-argus.dtsi @@ -0,0 +1,109 @@ +/* + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include + +/ { + ocp { + P8_07_pinmux { + /* gpio2[2] */ + status = "disabled"; + }; + P8_08_pinmux { + /* gpio2[3] */ + status = "disabled"; + }; + P8_09_pinmux { + /* gpio2[5] */ + status = "disabled"; + }; + P8_10_pinmux { + /* gpio2[4] */ + status = "disabled"; + }; + P9_11_pinmux { + /* gpio0[30] */ + status = "disabled"; + }; + P9_17_pinmux { + /* gpio0[5] */ + status = "disabled"; + }; + P9_18_pinmux { + /* gpio0[4] */ + status = "disabled"; + }; + P9_41_pinmux { + /* gpio0[20] */ + status = "disabled"; + }; + P9_42_pinmux { + /* gpio0[7] */ + status = "disabled"; + }; + }; +}; + +/ { + argus-ups { + compatible = "argus-ups"; + status = "okay"; + + pinctrl-names = "default"; + pinctrl-0 = <&argus_ups_pins>; /* Refer to previous label */ + /* This section communicates the gpio numbers to the driver module */ + /* Note that gpio controllers appear to be numbered from 1-n here rather than 0-(n-1)????? */ + gpios = <&gpio0 30 0>, /* Request */ + <&gpio0 5 0>, /* Acknowledge */ + <&gpio0 4 0>, /* Watchdog */ + <&gpio2 2 0>, /* LED 1 Green */ + <&gpio2 3 0>, /* LED 1 Red */ + <&gpio2 5 0>, /* LED 2 Green */ + <&gpio2 4 0>, /* LED 2 Red */ + <&gpio0 20 0>, /* General Output #1 */ + <&gpio0 7 0>; /* General Output #2 */ + debug = <1>; + shutdown = <1>; + }; +}; + +&am33xx_pinmux { + argus_ups_pins: pinmux_argus_ups_pins { /* Set up pinmux */ + pinctrl-single,pins = < + 0x070 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_wait0.gpio0_30 */ + 0x15c (PIN_OUTPUT_PULLUP | MUX_MODE7) /* spi0_cs0.gpio0_5 */ + 0x158 (PIN_OUTPUT_PULLUP | MUX_MODE7) /* spi0_d1.gpio0_4 */ + 0x090 (PIN_OUTPUT_PULLUP | MUX_MODE7) /* gpmc_advn_ale.gpio_2 */ + 0x094 (PIN_OUTPUT_PULLUP | MUX_MODE7) /* gpmc_oen_ren.gpio2_3 */ + 0x09c (PIN_OUTPUT_PULLUP | MUX_MODE7) /* gpmc_ben0_cle.gpio2_5 */ + 0x098 (PIN_OUTPUT_PULLUP | MUX_MODE7) /* gpmc_gpmc_wen.gpio2_4 */ + 0x1b4 (PIN_OUTPUT_PULLUP | MUX_MODE7) /* xdma_event_intr1.gpio0_20 */ + 0x164 (PIN_OUTPUT_PULLUP | MUX_MODE7) /* ecap0_in_pwm0_out.gpio0_7 */ + >; + }; + + i2c2_pins: pinmux_i2c2_pins { + pinctrl-single,pins = < + BONE_P9_20 0x73 /* (SLEWCTRL_SLOW | PIN_INPUT_PULLUP | MUX_MODE3) uart1_ctsn.i2c2_sda */ + BONE_P9_19 0x73 /* (SLEWCTRL_SLOW | PIN_INPUT_PULLUP | MUX_MODE3) uart1_rtsn.i2c2_scl */ + >; + }; +}; + +&i2c2 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c2_pins>; + + status = "okay"; + clock-frequency = <100000>; + + rtc@68 { + compatible = "maxim,ds1307"; + reg = <0x68>; + }; +}; diff --git b/arch/arm/boot/dts/am335x-bone-cape-bone-argus.dts b/arch/arm/boot/dts/am335x-bone-cape-bone-argus.dts new file mode 100644 index 000000000..82218f5e5 --- /dev/null +++ b/arch/arm/boot/dts/am335x-bone-cape-bone-argus.dts @@ -0,0 +1,28 @@ +/* + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +/dts-v1/; + +#include "am33xx.dtsi" +#include "am335x-bone-common-no-capemgr.dtsi" + +/ { + model = "TI AM335x BeagleBone"; + compatible = "ti,am335x-bone", "ti,am33xx"; +}; + +&ldo3_reg { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; +}; + +&mmc1 { + vmmc-supply = <&ldo3_reg>; +}; + +#include "am335x-bone-argus.dtsi" diff --git b/arch/arm/boot/dts/am335x-bone-common-no-capemgr.dtsi b/arch/arm/boot/dts/am335x-bone-common-no-capemgr.dtsi new file mode 100644 index 000000000..56b9ccfd5 --- /dev/null +++ b/arch/arm/boot/dts/am335x-bone-common-no-capemgr.dtsi @@ -0,0 +1,362 @@ +/* + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include + +/ { + cpus { + cpu@0 { + cpu0-supply = <&dcdc2_reg>; + }; + }; + + memory@80000000 { + device_type = "memory"; + reg = <0x80000000 0x10000000>; /* 256 MB */ + }; + + chosen { + stdout-path = &uart0; + }; + + leds { + pinctrl-names = "default"; + pinctrl-0 = <&user_leds_s0>; + + compatible = "gpio-leds"; + + led2 { + label = "beaglebone:green:usr0"; + gpios = <&gpio1 21 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "heartbeat"; + default-state = "off"; + }; + + led3 { + label = "beaglebone:green:usr1"; + gpios = <&gpio1 22 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "mmc0"; + default-state = "off"; + }; + + led4 { + label = "beaglebone:green:usr2"; + gpios = <&gpio1 23 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "cpu0"; + default-state = "off"; + }; + + led5 { + label = "beaglebone:green:usr3"; + gpios = <&gpio1 24 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "mmc1"; + default-state = "off"; + }; + }; + + vmmcsd_fixed: fixedregulator0 { + compatible = "regulator-fixed"; + regulator-name = "vmmcsd_fixed"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; +}; + +&am33xx_pinmux { + user_leds_s0: user_leds_s0 { + pinctrl-single,pins = < + AM33XX_IOPAD(0x854, PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a5.gpio1_21 */ + AM33XX_IOPAD(0x858, PIN_OUTPUT_PULLUP | MUX_MODE7) /* gpmc_a6.gpio1_22 */ + AM33XX_IOPAD(0x85c, PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a7.gpio1_23 */ + AM33XX_IOPAD(0x860, PIN_OUTPUT_PULLUP | MUX_MODE7) /* gpmc_a8.gpio1_24 */ + >; + }; + + i2c0_pins: pinmux_i2c0_pins { + pinctrl-single,pins = < + AM33XX_IOPAD(0x988, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_sda.i2c0_sda */ + AM33XX_IOPAD(0x98c, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_scl.i2c0_scl */ + >; + }; + + i2c2_pins: pinmux_i2c2_pins { + pinctrl-single,pins = < + AM33XX_IOPAD(0x978, PIN_INPUT_PULLUP | MUX_MODE3) /* uart1_ctsn.i2c2_sda */ + AM33XX_IOPAD(0x97c, PIN_INPUT_PULLUP | MUX_MODE3) /* uart1_rtsn.i2c2_scl */ + >; + }; + + uart0_pins: pinmux_uart0_pins { + pinctrl-single,pins = < + AM33XX_IOPAD(0x970, PIN_INPUT_PULLUP | MUX_MODE0) /* uart0_rxd.uart0_rxd */ + AM33XX_IOPAD(0x974, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart0_txd.uart0_txd */ + >; + }; + + cpsw_default: cpsw_default { + pinctrl-single,pins = < + /* Slave 1 */ + 0x108 (PIN_INPUT | MUX_MODE0) /* mii1_col.mii1_col */ + 0x10c (PIN_INPUT | MUX_MODE0) /* mii1_crs.mii1_crs */ + AM33XX_IOPAD(0x910, PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxerr.mii1_rxerr */ + AM33XX_IOPAD(0x914, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mii1_txen.mii1_txen */ + AM33XX_IOPAD(0x918, PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxdv.mii1_rxdv */ + AM33XX_IOPAD(0x91c, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mii1_txd3.mii1_txd3 */ + AM33XX_IOPAD(0x920, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mii1_txd2.mii1_txd2 */ + AM33XX_IOPAD(0x924, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mii1_txd1.mii1_txd1 */ + AM33XX_IOPAD(0x928, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mii1_txd0.mii1_txd0 */ + AM33XX_IOPAD(0x92c, PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_txclk.mii1_txclk */ + AM33XX_IOPAD(0x930, PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxclk.mii1_rxclk */ + AM33XX_IOPAD(0x934, PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxd3.mii1_rxd3 */ + AM33XX_IOPAD(0x938, PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxd2.mii1_rxd2 */ + AM33XX_IOPAD(0x93c, PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxd1.mii1_rxd1 */ + AM33XX_IOPAD(0x940, PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxd0.mii1_rxd0 */ + >; + }; + + cpsw_sleep: cpsw_sleep { + pinctrl-single,pins = < + /* Slave 1 reset value */ + 0x108 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x10c (PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x910, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x914, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x918, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x91c, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x920, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x924, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x928, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x92c, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x930, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x934, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x938, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x93c, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x940, PIN_INPUT_PULLDOWN | MUX_MODE7) + >; + }; + + davinci_mdio_default: davinci_mdio_default { + pinctrl-single,pins = < + /* MDIO */ + AM33XX_IOPAD(0x948, PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* mdio_data.mdio_data */ + AM33XX_IOPAD(0x94c, PIN_OUTPUT_PULLUP | MUX_MODE0) /* mdio_clk.mdio_clk */ + >; + }; + + davinci_mdio_sleep: davinci_mdio_sleep { + pinctrl-single,pins = < + /* MDIO reset value */ + AM33XX_IOPAD(0x948, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM33XX_IOPAD(0x94c, PIN_INPUT_PULLDOWN | MUX_MODE7) + >; + }; + + mmc1_pins: pinmux_mmc1_pins { + pinctrl-single,pins = < + AM33XX_IOPAD(0x960, PIN_INPUT | MUX_MODE7) /* GPIO0_6 */ + >; + }; + + emmc_pins: pinmux_emmc_pins { + pinctrl-single,pins = < + AM33XX_IOPAD(0x880, PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_csn1.mmc1_clk */ + AM33XX_IOPAD(0x884, PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_csn2.mmc1_cmd */ + AM33XX_IOPAD(0x800, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad0.mmc1_dat0 */ + AM33XX_IOPAD(0x804, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad1.mmc1_dat1 */ + AM33XX_IOPAD(0x808, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad2.mmc1_dat2 */ + AM33XX_IOPAD(0x80c, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad3.mmc1_dat3 */ + AM33XX_IOPAD(0x810, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad4.mmc1_dat4 */ + AM33XX_IOPAD(0x814, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad5.mmc1_dat5 */ + AM33XX_IOPAD(0x818, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad6.mmc1_dat6 */ + AM33XX_IOPAD(0x81c, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad7.mmc1_dat7 */ + >; + }; +}; + +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_pins>; + + status = "okay"; +}; + +&usb { + status = "okay"; +}; + +&usb_ctrl_mod { + status = "okay"; +}; + +&usb0_phy { + status = "okay"; +}; + +&usb1_phy { + status = "okay"; +}; + +&usb0 { + status = "okay"; + dr_mode = "peripheral"; +}; + +&usb1 { + status = "okay"; + dr_mode = "host"; +}; + +&cppi41dma { + status = "okay"; +}; + +&i2c0 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_pins>; + + status = "okay"; + clock-frequency = <400000>; + + tps: tps@24 { + reg = <0x24>; + }; + + baseboard_eeprom: baseboard_eeprom@50 { + compatible = "at,24c256"; + reg = <0x50>; + + #address-cells = <1>; + #size-cells = <1>; + baseboard_data: baseboard_data@0 { + reg = <0 0x100>; + }; + }; +}; + +/include/ "tps65217.dtsi" + +&tps { + /* + * Configure pmic to enter OFF-state instead of SLEEP-state ("RTC-only + * mode") at poweroff. Most BeagleBone versions do not support RTC-only + * mode and risk hardware damage if this mode is entered. + * + * For details, see linux-omap mailing list May 2015 thread + * [PATCH] ARM: dts: am335x-bone* enable pmic-shutdown-controller + * In particular, messages: + * http://www.spinics.net/lists/linux-omap/msg118585.html + * http://www.spinics.net/lists/linux-omap/msg118615.html + * + * You can override this later with + * &tps { /delete-property/ ti,pmic-shutdown-controller; } + * if you want to use RTC-only mode and made sure you are not affected + * by the hardware problems. (Tip: double-check by performing a current + * measurement after shutdown: it should be less than 1 mA.) + */ + + interrupts = <7>; /* NMI */ + interrupt-parent = <&intc>; + + ti,pmic-shutdown-controller; + + charger { + interrupts = , ; + interrupts-names = "AC", "USB"; + status = "okay"; + }; + + pwrbutton { + interrupts = ; + status = "okay"; + }; + + regulators { + dcdc1_reg: regulator@0 { + regulator-name = "vdds_dpr"; + regulator-always-on; + }; + + dcdc2_reg: regulator@1 { + /* VDD_MPU voltage limits 0.95V - 1.26V with +/-4% tolerance */ + regulator-name = "vdd_mpu"; + regulator-min-microvolt = <925000>; + regulator-max-microvolt = <1351500>; + regulator-boot-on; + regulator-always-on; + }; + + dcdc3_reg: regulator@2 { + /* VDD_CORE voltage limits 0.95V - 1.1V with +/-4% tolerance */ + regulator-name = "vdd_core"; + regulator-min-microvolt = <925000>; + regulator-max-microvolt = <1150000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo1_reg: regulator@3 { + regulator-name = "vio,vrtc,vdds"; + regulator-always-on; + }; + + ldo2_reg: regulator@4 { + regulator-name = "vdd_3v3aux"; + regulator-always-on; + }; + + ldo3_reg: regulator@5 { + regulator-name = "vdd_1v8"; + regulator-always-on; + }; + + ldo4_reg: regulator@6 { + regulator-name = "vdd_3v3a"; + regulator-always-on; + }; + }; +}; + +&cpsw_emac0 { + phy_id = <&davinci_mdio>, <0>; + phy-mode = "mii"; +}; + +&mac { + slaves = <1>; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&cpsw_default>; + pinctrl-1 = <&cpsw_sleep>; + status = "okay"; +}; + +&davinci_mdio { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&davinci_mdio_default>; + pinctrl-1 = <&davinci_mdio_sleep>; + status = "okay"; +}; + +&mmc1 { + status = "okay"; + bus-width = <0x4>; + pinctrl-names = "default"; + pinctrl-0 = <&mmc1_pins>; + cd-gpios = <&gpio0 6 GPIO_ACTIVE_LOW>; +}; + +&aes { + status = "okay"; +}; + +&sham { + status = "okay"; +}; + +&rtc { + system-power-controller; +}; diff --git b/arch/arm/boot/dts/am335x-bone-common-universal-pins.dtsi b/arch/arm/boot/dts/am335x-bone-common-universal-pins.dtsi new file mode 100644 index 000000000..e4d4971a3 --- /dev/null +++ b/arch/arm/boot/dts/am335x-bone-common-universal-pins.dtsi @@ -0,0 +1,941 @@ +/* + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +&am33xx_pinmux { + /************************/ + /* P8 Header */ + /************************/ + + /* P8_01 GND */ + /* P8_02 GND */ + /* P8_03 (ZCZ ball R9 ) emmc */ + /* P8_04 (ZCZ ball T9 ) emmc */ + /* P8_05 (ZCZ ball R8 ) emmc */ + /* P8_06 (ZCZ ball T8 ) emmc */ + + /* P8_07 (ZCZ ball R7 ) */ + P8_07_default_pin: pinmux_P8_07_default_pin { + pinctrl-single,pins = <0x090 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_07_gpio_pin: pinmux_P8_07_gpio_pin { + pinctrl-single,pins = <0x090 0x2F>; }; /* Mode 7, RxActive */ + P8_07_gpio_pu_pin: pinmux_P8_07_gpio_pu_pin { + pinctrl-single,pins = <0x090 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_07_gpio_pd_pin: pinmux_P8_07_gpio_pd_pin { + pinctrl-single,pins = <0x090 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_07_timer_pin: pinmux_P8_07_timer_pin { + pinctrl-single,pins = <0x090 0x32>; }; /* Mode 2, Pull-Up, RxActive */ + + /* P8_08 (ZCZ ball T7 ) */ + P8_08_default_pin: pinmux_P8_08_default_pin { + pinctrl-single,pins = <0x094 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_08_gpio_pin: pinmux_P8_08_gpio_pin { + pinctrl-single,pins = <0x094 0x2F>; }; /* Mode 7, RxActive */ + P8_08_gpio_pu_pin: pinmux_P8_08_gpio_pu_pin { + pinctrl-single,pins = <0x094 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_08_gpio_pd_pin: pinmux_P8_08_gpio_pd_pin { + pinctrl-single,pins = <0x094 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_08_timer_pin: pinmux_P8_08_timer_pin { + pinctrl-single,pins = <0x094 0x32>; }; /* Mode 2, Pull-Up, RxActive */ + + /* P8_09 (ZCZ ball T6 ) */ + P8_09_default_pin: pinmux_P8_09_default_pin { + pinctrl-single,pins = <0x09c 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_09_gpio_pin: pinmux_P8_09_gpio_pin { + pinctrl-single,pins = <0x09c 0x2F>; }; /* Mode 7, RxActive */ + P8_09_gpio_pu_pin: pinmux_P8_09_gpio_pu_pin { + pinctrl-single,pins = <0x09c 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_09_gpio_pd_pin: pinmux_P8_09_gpio_pd_pin { + pinctrl-single,pins = <0x09c 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_09_timer_pin: pinmux_P8_09_timer_pin { + pinctrl-single,pins = <0x09c 0x32>; }; /* Mode 2, Pull-Up, RxActive */ + + /* P8_10 (ZCZ ball U6 ) */ + P8_10_default_pin: pinmux_P8_10_default_pin { + pinctrl-single,pins = <0x098 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_10_gpio_pin: pinmux_P8_10_gpio_pin { + pinctrl-single,pins = <0x098 0x2F>; }; /* Mode 7, RxActive */ + P8_10_gpio_pu_pin: pinmux_P8_10_gpio_pu_pin { + pinctrl-single,pins = <0x098 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_10_gpio_pd_pin: pinmux_P8_10_gpio_pd_pin { + pinctrl-single,pins = <0x098 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_10_timer_pin: pinmux_P8_10_timer_pin { + pinctrl-single,pins = <0x098 0x32>; }; /* Mode 2, Pull-Up, RxActive */ + + /* P8_11 (ZCZ ball R12) */ + P8_11_default_pin: pinmux_P8_11_default_pin { + pinctrl-single,pins = <0x034 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_11_gpio_pin: pinmux_P8_11_gpio_pin { + pinctrl-single,pins = <0x034 0x2F>; }; /* Mode 7, RxActive */ + P8_11_gpio_pu_pin: pinmux_P8_11_gpio_pu_pin { + pinctrl-single,pins = <0x034 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_11_gpio_pd_pin: pinmux_P8_11_gpio_pd_pin { + pinctrl-single,pins = <0x034 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_11_pruout_pin: pinmux_P8_11_pruout_pin { + pinctrl-single,pins = <0x034 0x26>; }; /* Mode 6, Pull-Down, RxActive */ + P8_11_qep_pin: pinmux_P8_11_qep_pin { + pinctrl-single,pins = <0x034 0x24>; }; /* Mode 4, Pull-Down, RxActive */ + + /* P8_12 (ZCZ ball T12) */ + P8_12_default_pin: pinmux_P8_12_default_pin { + pinctrl-single,pins = <0x030 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_12_gpio_pin: pinmux_P8_12_gpio_pin { + pinctrl-single,pins = <0x030 0x2F>; }; /* Mode 7, RxActive */ + P8_12_gpio_pu_pin: pinmux_P8_12_gpio_pu_pin { + pinctrl-single,pins = <0x030 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_12_gpio_pd_pin: pinmux_P8_12_gpio_pd_pin { + pinctrl-single,pins = <0x030 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_12_pruout_pin: pinmux_P8_12_pruout_pin { + pinctrl-single,pins = <0x030 0x26>; }; /* Mode 6, Pull-Down, RxActive */ + P8_12_qep_pin: pinmux_P8_12_qep_pin { + pinctrl-single,pins = <0x030 0x24>; }; /* Mode 4, Pull-Down, RxActive */ + + /* P8_13 (ZCZ ball T10) */ + P8_13_default_pin: pinmux_P8_13_default_pin { + pinctrl-single,pins = <0x024 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_13_gpio_pin: pinmux_P8_13_gpio_pin { + pinctrl-single,pins = <0x024 0x2F>; }; /* Mode 7, RxActive */ + P8_13_gpio_pu_pin: pinmux_P8_13_gpio_pu_pin { + pinctrl-single,pins = <0x024 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_13_gpio_pd_pin: pinmux_P8_13_gpio_pd_pin { + pinctrl-single,pins = <0x024 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_13_pwm_pin: pinmux_P8_13_pwm_pin { + pinctrl-single,pins = <0x024 0x24>; }; /* Mode 4, Pull-Down, RxActive */ + + /* P8_14 (ZCZ ball T11) */ + P8_14_default_pin: pinmux_P8_14_default_pin { + pinctrl-single,pins = <0x028 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_14_gpio_pin: pinmux_P8_14_gpio_pin { + pinctrl-single,pins = <0x028 0x2F>; }; /* Mode 7, RxActive */ + P8_14_gpio_pu_pin: pinmux_P8_14_gpio_pu_pin { + pinctrl-single,pins = <0x028 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_14_gpio_pd_pin: pinmux_P8_14_gpio_pd_pin { + pinctrl-single,pins = <0x028 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_14_pwm_pin: pinmux_P8_14_pwm_pin { + pinctrl-single,pins = <0x028 0x24>; }; /* Mode 4, Pull-Down, RxActive */ + + /* P8_15 (ZCZ ball U13) */ + P8_15_default_pin: pinmux_P8_15_default_pin { + pinctrl-single,pins = <0x03c 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_15_gpio_pin: pinmux_P8_15_gpio_pin { + pinctrl-single,pins = <0x03c 0x2F>; }; /* Mode 7, RxActive */ + P8_15_gpio_pu_pin: pinmux_P8_15_gpio_pu_pin { + pinctrl-single,pins = <0x03c 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_15_gpio_pd_pin: pinmux_P8_15_gpio_pd_pin { + pinctrl-single,pins = <0x03c 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_15_pruin_pin: pinmux_P8_15_pruin_pin { + pinctrl-single,pins = <0x03c 0x26>; }; /* Mode 6, Pull-Down, RxActive */ + P8_15_qep_pin: pinmux_P8_15_qep_pin { + pinctrl-single,pins = <0x03c 0x24>; }; /* Mode 4, Pull-Down, RxActive */ + + /* P8_16 (ZCZ ball V13) */ + P8_16_default_pin: pinmux_P8_16_default_pin { + pinctrl-single,pins = <0x038 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_16_gpio_pin: pinmux_P8_16_gpio_pin { + pinctrl-single,pins = <0x038 0x2F>; }; /* Mode 7, RxActive */ + P8_16_gpio_pu_pin: pinmux_P8_16_gpio_pu_pin { + pinctrl-single,pins = <0x038 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_16_gpio_pd_pin: pinmux_P8_16_gpio_pd_pin { + pinctrl-single,pins = <0x038 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_16_pruin_pin: pinmux_P8_16_pruin_pin { + pinctrl-single,pins = <0x038 0x26>; }; /* Mode 6, Pull-Down, RxActive */ + P8_16_qep_pin: pinmux_P8_16_qep_pin { + pinctrl-single,pins = <0x038 0x24>; }; /* Mode 4, Pull-Down, RxActive */ + + /* P8_17 (ZCZ ball U12) */ + P8_17_default_pin: pinmux_P8_17_default_pin { + pinctrl-single,pins = <0x02c 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_17_gpio_pin: pinmux_P8_17_gpio_pin { + pinctrl-single,pins = <0x02c 0x2F>; }; /* Mode 7, RxActive */ + P8_17_gpio_pu_pin: pinmux_P8_17_gpio_pu_pin { + pinctrl-single,pins = <0x02c 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_17_gpio_pd_pin: pinmux_P8_17_gpio_pd_pin { + pinctrl-single,pins = <0x02c 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_17_pwm_pin: pinmux_P8_17_pwm_pin { + pinctrl-single,pins = <0x02c 0x24>; }; /* Mode 4, Pull-Down, RxActive */ + + /* P8_18 (ZCZ ball V12) */ + P8_18_default_pin: pinmux_P8_18_default_pin { + pinctrl-single,pins = <0x08c 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_18_gpio_pin: pinmux_P8_18_gpio_pin { + pinctrl-single,pins = <0x08c 0x2F>; }; /* Mode 7, RxActive */ + P8_18_gpio_pu_pin: pinmux_P8_18_gpio_pu_pin { + pinctrl-single,pins = <0x08c 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_18_gpio_pd_pin: pinmux_P8_18_gpio_pd_pin { + pinctrl-single,pins = <0x08c 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + + /* P8_19 (ZCZ ball U10) */ + P8_19_default_pin: pinmux_P8_19_default_pin { + pinctrl-single,pins = <0x020 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_19_gpio_pin: pinmux_P8_19_gpio_pin { + pinctrl-single,pins = <0x020 0x2F>; }; /* Mode 7, RxActive */ + P8_19_gpio_pu_pin: pinmux_P8_19_gpio_pu_pin { + pinctrl-single,pins = <0x020 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_19_gpio_pd_pin: pinmux_P8_19_gpio_pd_pin { + pinctrl-single,pins = <0x020 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_19_pwm_pin: pinmux_P8_19_pwm_pin { + pinctrl-single,pins = <0x020 0x24>; }; /* Mode 4, Pull-Down, RxActive */ + + /* P8_20 (ZCZ ball V9 ) emmc */ + /* P8_21 (ZCZ ball U9 ) emmc */ + /* P8_22 (ZCZ ball V8 ) emmc */ + /* P8_23 (ZCZ ball U8 ) emmc */ + /* P8_24 (ZCZ ball V7 ) emmc */ + /* P8_25 (ZCZ ball U7 ) emmc */ + + /* P8_26 (ZCZ ball V6 ) */ + P8_26_default_pin: pinmux_P8_26_default_pin { + pinctrl-single,pins = <0x07c 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_26_gpio_pin: pinmux_P8_26_gpio_pin { + pinctrl-single,pins = <0x07c 0x2F>; }; /* Mode 7, RxActive */ + P8_26_gpio_pu_pin: pinmux_P8_26_gpio_pu_pin { + pinctrl-single,pins = <0x07c 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_26_gpio_pd_pin: pinmux_P8_26_gpio_pd_pin { + pinctrl-single,pins = <0x07c 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + + /* P8_27 (ZCZ ball U5 ) hdmi */ + P8_27_default_pin: pinmux_P8_27_default_pin { + pinctrl-single,pins = <0x0e0 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_27_gpio_pin: pinmux_P8_27_gpio_pin { + pinctrl-single,pins = <0x0e0 0x2F>; }; /* Mode 7, RxActive */ + P8_27_gpio_pu_pin: pinmux_P8_27_gpio_pu_pin { + pinctrl-single,pins = <0x0e0 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_27_gpio_pd_pin: pinmux_P8_27_gpio_pd_pin { + pinctrl-single,pins = <0x0e0 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_27_pruout_pin: pinmux_P8_27_pruout_pin { + pinctrl-single,pins = <0x0e0 0x05>; }; /* Mode 5, Pull-Down*/ + P8_27_pruin_pin: pinmux_P8_27_pruin_pin { + pinctrl-single,pins = <0x0e0 0x26>; }; /* Mode 6, Pull-Down, RxActive */ + P8_27_hdmi_pin: pinmux_P8_27_hdmi_pin { + pinctrl-single,pins = <0x0e0 0x00>; }; /* lcd_vsync.lcd_vsync, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT */ + + /* P8_28 (ZCZ ball V5 ) hdmi */ + P8_28_default_pin: pinmux_P8_28_default_pin { + pinctrl-single,pins = <0x0e8 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_28_gpio_pin: pinmux_P8_28_gpio_pin { + pinctrl-single,pins = <0x0e8 0x2F>; }; /* Mode 7, RxActive */ + P8_28_gpio_pu_pin: pinmux_P8_28_gpio_pu_pin { + pinctrl-single,pins = <0x0e8 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_28_gpio_pd_pin: pinmux_P8_28_gpio_pd_pin { + pinctrl-single,pins = <0x0e8 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_28_pruout_pin: pinmux_P8_28_pruout_pin { + pinctrl-single,pins = <0x0e8 0x05>; }; /* Mode 5, Pull-Down */ + P8_28_pruin_pin: pinmux_P8_28_pruin_pin { + pinctrl-single,pins = <0x0e8 0x26>; }; /* Mode 6, Pull-Down, RxActive */ + P8_28_hdmi_pin: pinmux_P8_28_hdmi_pin { + pinctrl-single,pins = <0x0e8 0x00>; }; /* lcd_pclk.lcd_pclk, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT */ + + /* P8_29 (ZCZ ball R5 ) hdmi */ + P8_29_default_pin: pinmux_P8_29_default_pin { + pinctrl-single,pins = <0x0e4 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_29_gpio_pin: pinmux_P8_29_gpio_pin { + pinctrl-single,pins = <0x0e4 0x2F>; }; /* Mode 7, RxActive */ + P8_29_gpio_pu_pin: pinmux_P8_29_gpio_pu_pin { + pinctrl-single,pins = <0x0e4 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_29_gpio_pd_pin: pinmux_P8_29_gpio_pd_pin { + pinctrl-single,pins = <0x0e4 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_29_pruout_pin: pinmux_P8_29_pruout_pin { + pinctrl-single,pins = <0x0e4 0x05>; }; /* Mode 5, Pull-Down*/ + P8_29_pruin_pin: pinmux_P8_29_pruin_pin { + pinctrl-single,pins = <0x0e4 0x26>; }; /* Mode 6, Pull-Down, RxActive */ + P8_29_hdmi_pin: pinmux_P8_29_hdmi_pin { + pinctrl-single,pins = <0x0e4 0x00>; }; /* lcd_hsync.lcd_hsync, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT */ + + /* P8_30 (ZCZ ball R6 ) hdmi */ + P8_30_default_pin: pinmux_P8_30_default_pin { + pinctrl-single,pins = <0x0ec 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_30_gpio_pin: pinmux_P8_30_gpio_pin { + pinctrl-single,pins = <0x0ec 0x2F>; }; /* Mode 7, RxActive */ + P8_30_gpio_pu_pin: pinmux_P8_30_gpio_pu_pin { + pinctrl-single,pins = <0x0ec 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_30_gpio_pd_pin: pinmux_P8_30_gpio_pd_pin { + pinctrl-single,pins = <0x0ec 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_30_pruout_pin: pinmux_P8_30_pruout_pin { + pinctrl-single,pins = <0x0ec 0x05>; }; /* Mode 5, Pull-Down*/ + P8_30_pruin_pin: pinmux_P8_30_pruin_pin { + pinctrl-single,pins = <0x0ec 0x26>; }; /* Mode 6, Pull-Down, RxActive */ + P8_30_hdmi_pin: pinmux_P8_30_hdmi_pin { + pinctrl-single,pins = <0x0ec 0x00>; }; /* lcd_ac_bias_en.lcd_ac_bias_en, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT */ + + /* P8_31 (ZCZ ball V4 ) hdmi */ + P8_31_default_pin: pinmux_P8_31_default_pin { + pinctrl-single,pins = <0x0d8 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_31_gpio_pin: pinmux_P8_31_gpio_pin { + pinctrl-single,pins = <0x0d8 0x2F>; }; /* Mode 7, RxActive */ + P8_31_gpio_pu_pin: pinmux_P8_31_gpio_pu_pin { + pinctrl-single,pins = <0x0d8 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_31_gpio_pd_pin: pinmux_P8_31_gpio_pd_pin { + pinctrl-single,pins = <0x0d8 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_31_uart_pin: pinmux_P8_31_uart_pin { + pinctrl-single,pins = <0x0d8 0x24>; }; /* Mode 4, Pull-Down, RxActive */ + P8_31_hdmi_pin: pinmux_P8_31_hdmi_pin { + pinctrl-single,pins = <0x0d8 0x08>; }; /* lcd_data14.lcd_data14, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ + + /* P8_32 (ZCZ ball T5 ) hdmi */ + P8_32_default_pin: pinmux_P8_32_default_pin { + pinctrl-single,pins = <0x0dc 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_32_gpio_pin: pinmux_P8_32_gpio_pin { + pinctrl-single,pins = <0x0dc 0x2F>; }; /* Mode 7, RxActive */ + P8_32_gpio_pu_pin: pinmux_P8_32_gpio_pu_pin { + pinctrl-single,pins = <0x0dc 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_32_gpio_pd_pin: pinmux_P8_32_gpio_pd_pin { + pinctrl-single,pins = <0x0dc 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_32_uart_pin: pinmux_P8_32_uart_pin { + pinctrl-single,pins = <0x0dc 0x26>; }; /* Mode 6, Pull-Down, RxActive */ + P8_32_hdmi_pin: pinmux_P8_32_hdmi_pin { + pinctrl-single,pins = <0x0dc 0x08>; }; /* lcd_data15.lcd_data15, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ + + /* P8_33 (ZCZ ball V3 ) hdmi */ + P8_33_default_pin: pinmux_P8_33_default_pin { + pinctrl-single,pins = <0x0d4 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_33_gpio_pin: pinmux_P8_33_gpio_pin { + pinctrl-single,pins = <0x0d4 0x2F>; }; /* Mode 7, RxActive */ + P8_33_gpio_pu_pin: pinmux_P8_33_gpio_pu_pin { + pinctrl-single,pins = <0x0d4 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_33_gpio_pd_pin: pinmux_P8_33_gpio_pd_pin { + pinctrl-single,pins = <0x0d4 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_33_hdmi_pin: pinmux_P8_33_hdmi_pin { + pinctrl-single,pins = <0x0d4 0x08>; }; /* lcd_data13.lcd_data13, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ + P8_33_qep_pin: pinmux_P8_33_qep_pin { + pinctrl-single,pins = <0x0d4 0x22>; }; /* Mode 2, Pull-Down, RxActive */ + + /* P8_34 (ZCZ ball U4 ) hdmi */ + P8_34_default_pin: pinmux_P8_34_default_pin { + pinctrl-single,pins = <0x0cc 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_34_gpio_pin: pinmux_P8_34_gpio_pin { + pinctrl-single,pins = <0x0cc 0x2F>; }; /* Mode 7, RxActive */ + P8_34_gpio_pu_pin: pinmux_P8_34_gpio_pu_pin { + pinctrl-single,pins = <0x0cc 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_34_gpio_pd_pin: pinmux_P8_34_gpio_pd_pin { + pinctrl-single,pins = <0x0cc 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_34_pwm_pin: pinmux_P8_34_pwm_pin { + pinctrl-single,pins = <0x0cc 0x22>; }; /* Mode 2, Pull-Down, RxActive */ + P8_34_hdmi_pin: pinmux_P8_34_hdmi_pin { + pinctrl-single,pins = <0x0cc 0x08>; }; /* lcd_data11.lcd_data11, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ + + /* P8_35 (ZCZ ball V2 ) hdmi */ + P8_35_default_pin: pinmux_P8_35_default_pin { + pinctrl-single,pins = <0x0d0 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_35_gpio_pin: pinmux_P8_35_gpio_pin { + pinctrl-single,pins = <0x0d0 0x2F>; }; /* Mode 7, RxActive */ + P8_35_gpio_pu_pin: pinmux_P8_35_gpio_pu_pin { + pinctrl-single,pins = <0x0d0 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_35_gpio_pd_pin: pinmux_P8_35_gpio_pd_pin { + pinctrl-single,pins = <0x0d0 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_35_hdmi_pin: pinmux_P8_35_hdmi_pin { + pinctrl-single,pins = <0x0d0 0x08>; }; /* lcd_data12.lcd_data12, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ + P8_35_qep_pin: pinmux_P8_35_qep_pin { + pinctrl-single,pins = <0x0d0 0x22>; }; /* Mode 2, Pull-Down, RxActive */ + + /* P8_36 (ZCZ ball U3 ) hdmi */ + P8_36_default_pin: pinmux_P8_36_default_pin { + pinctrl-single,pins = <0x0c8 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_36_gpio_pin: pinmux_P8_36_gpio_pin { + pinctrl-single,pins = <0x0c8 0x2F>; }; /* Mode 7, RxActive */ + P8_36_gpio_pu_pin: pinmux_P8_36_gpio_pu_pin { + pinctrl-single,pins = <0x0c8 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_36_gpio_pd_pin: pinmux_P8_36_gpio_pd_pin { + pinctrl-single,pins = <0x0c8 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_36_pwm_pin: pinmux_P8_36_pwm_pin { + pinctrl-single,pins = <0x0c8 0x22>; }; /* Mode 2, Pull-Down, RxActive */ + P8_36_hdmi_pin: pinmux_P8_36_hdmi_pin { + pinctrl-single,pins = <0x0c8 0x08>; }; /* lcd_data10.lcd_data10, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ + + /* P8_37 (ZCZ ball U1 ) hdmi */ + P8_37_default_pin: pinmux_P8_37_default_pin { + pinctrl-single,pins = <0x0c0 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_37_gpio_pin: pinmux_P8_37_gpio_pin { + pinctrl-single,pins = <0x0c0 0x2F>; }; /* Mode 7, RxActive */ + P8_37_gpio_pu_pin: pinmux_P8_37_gpio_pu_pin { + pinctrl-single,pins = <0x0c0 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_37_gpio_pd_pin: pinmux_P8_37_gpio_pd_pin { + pinctrl-single,pins = <0x0c0 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_37_uart_pin: pinmux_P8_37_uart_pin { + pinctrl-single,pins = <0x0c0 0x04>; }; /* Mode 4, Pull-Down*/ + P8_37_pwm_pin: pinmux_P8_37_pwm_pin { + pinctrl-single,pins = <0x0c0 0x02>; }; /* Mode 2, Pull-Down*/ + P8_37_hdmi_pin: pinmux_P8_37_hdmi_pin { + pinctrl-single,pins = <0x0c0 0x08>; }; /* lcd_data8.lcd_data8, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ + + + /* P8_38 (ZCZ ball U2 ) hdmi */ + P8_38_default_pin: pinmux_P8_38_default_pin { + pinctrl-single,pins = <0x0c4 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_38_gpio_pin: pinmux_P8_38_gpio_pin { + pinctrl-single,pins = <0x0c4 0x2F>; }; /* Mode 7, RxActive */ + P8_38_gpio_pu_pin: pinmux_P8_38_gpio_pu_pin { + pinctrl-single,pins = <0x0c4 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_38_gpio_pd_pin: pinmux_P8_38_gpio_pd_pin { + pinctrl-single,pins = <0x0c4 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_38_uart_pin: pinmux_P8_38_uart_pin { + pinctrl-single,pins = <0x0c4 0x24>; }; /* Mode 4, Pull-Down, RxActive */ + P8_38_pwm_pin: pinmux_P8_38_pwm_pin { + pinctrl-single,pins = <0x0c4 0x22>; }; /* Mode 2, Pull-Down, RxActive */ + P8_38_hdmi_pin: pinmux_P8_38_hdmi_pin { + pinctrl-single,pins = <0x0c4 0x08>; }; /* lcd_data9.lcd_data9, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ + + + /* P8_39 (ZCZ ball T3 ) hdmi */ + P8_39_default_pin: pinmux_P8_39_default_pin { + pinctrl-single,pins = <0x0b8 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_39_gpio_pin: pinmux_P8_39_gpio_pin { + pinctrl-single,pins = <0x0b8 0x2F>; }; /* Mode 7, RxActive */ + P8_39_gpio_pu_pin: pinmux_P8_39_gpio_pu_pin { + pinctrl-single,pins = <0x0b8 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_39_gpio_pd_pin: pinmux_P8_39_gpio_pd_pin { + pinctrl-single,pins = <0x0b8 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_39_pruout_pin: pinmux_P8_39_pruout_pin { + pinctrl-single,pins = <0x0b8 0x05>; }; /* Mode 5, Pull-Down*/ + P8_39_pruin_pin: pinmux_P8_39_pruin_pin { + pinctrl-single,pins = <0x0b8 0x26>; }; /* Mode 6, Pull-Down, RxActive */ + P8_39_hdmi_pin: pinmux_P8_39_hdmi_pin { + pinctrl-single,pins = <0x0b8 0x08>; }; /* lcd_data6.lcd_data6, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ + + /* P8_40 (ZCZ ball T4 ) hdmi */ + P8_40_default_pin: pinmux_P8_40_default_pin { + pinctrl-single,pins = <0x0bc 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_40_gpio_pin: pinmux_P8_40_gpio_pin { + pinctrl-single,pins = <0x0bc 0x2F>; }; /* Mode 7, RxActive */ + P8_40_gpio_pu_pin: pinmux_P8_40_gpio_pu_pin { + pinctrl-single,pins = <0x0bc 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_40_gpio_pd_pin: pinmux_P8_40_gpio_pd_pin { + pinctrl-single,pins = <0x0bc 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_40_pruout_pin: pinmux_P8_40_pruout_pin { + pinctrl-single,pins = <0x0bc 0x05>; }; /* Mode 5, Pull-Down*/ + P8_40_pruin_pin: pinmux_P8_40_pruin_pin { + pinctrl-single,pins = <0x0bc 0x26>; }; /* Mode 6, Pull-Down, RxActive */ + P8_40_hdmi_pin: pinmux_P8_40_hdmi_pin { + pinctrl-single,pins = <0x0bc 0x08>; }; /* lcd_data7.lcd_data7, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ + + /* P8_41 (ZCZ ball T1 ) hdmi */ + P8_41_default_pin: pinmux_P8_41_default_pin { + pinctrl-single,pins = <0x0b0 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_41_gpio_pin: pinmux_P8_41_gpio_pin { + pinctrl-single,pins = <0x0b0 0x2F>; }; /* Mode 7, RxActive */ + P8_41_gpio_pu_pin: pinmux_P8_41_gpio_pu_pin { + pinctrl-single,pins = <0x0b0 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_41_gpio_pd_pin: pinmux_P8_41_gpio_pd_pin { + pinctrl-single,pins = <0x0b0 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_41_pruout_pin: pinmux_P8_41_pruout_pin { + pinctrl-single,pins = <0x0b0 0x05>; }; /* Mode 5, Pull-Down*/ + P8_41_pruin_pin: pinmux_P8_41_pruin_pin { + pinctrl-single,pins = <0x0b0 0x26>; }; /* Mode 6, Pull-Down, RxActive */ + P8_41_hdmi_pin: pinmux_P8_41_hdmi_pin { + pinctrl-single,pins = <0x0b0 0x08>; }; /* lcd_data4.lcd_data4, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ + + /* P8_42 (ZCZ ball T2 ) hdmi */ + P8_42_default_pin: pinmux_P8_42_default_pin { + pinctrl-single,pins = <0x0b4 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_42_gpio_pin: pinmux_P8_42_gpio_pin { + pinctrl-single,pins = <0x0b4 0x2F>; }; /* Mode 7, RxActive */ + P8_42_gpio_pu_pin: pinmux_P8_42_gpio_pu_pin { + pinctrl-single,pins = <0x0b4 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_42_gpio_pd_pin: pinmux_P8_42_gpio_pd_pin { + pinctrl-single,pins = <0x0b4 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_42_pruout_pin: pinmux_P8_42_pruout_pin { + pinctrl-single,pins = <0x0b4 0x05>; }; /* Mode 5, Pull-Down*/ + P8_42_pruin_pin: pinmux_P8_42_pruin_pin { + pinctrl-single,pins = <0x0b4 0x26>; }; /* Mode 6, Pull-Down, RxActive */ + P8_42_hdmi_pin: pinmux_P8_42_hdmi_pin { + pinctrl-single,pins = <0x0b4 0x08>; }; /* lcd_data5.lcd_data5, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ + + /* P8_43 (ZCZ ball R3 ) hdmi */ + P8_43_default_pin: pinmux_P8_43_default_pin { + pinctrl-single,pins = <0x0a8 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_43_gpio_pin: pinmux_P8_43_gpio_pin { + pinctrl-single,pins = <0x0a8 0x2F>; }; /* Mode 7, RxActive */ + P8_43_gpio_pu_pin: pinmux_P8_43_gpio_pu_pin { + pinctrl-single,pins = <0x0a8 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_43_gpio_pd_pin: pinmux_P8_43_gpio_pd_pin { + pinctrl-single,pins = <0x0a8 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_43_pruout_pin: pinmux_P8_43_pruout_pin { + pinctrl-single,pins = <0x0a8 0x05>; }; /* Mode 5, Pull-Down*/ + P8_43_pruin_pin: pinmux_P8_43_pruin_pin { + pinctrl-single,pins = <0x0a8 0x26>; }; /* Mode 6, Pull-Down, RxActive */ + P8_43_pwm_pin: pinmux_P8_43_pwm_pin { + pinctrl-single,pins = <0x0a8 0x03>; }; /* Mode 3, Pull-Down */ + P8_43_hdmi_pin: pinmux_P8_43_hdmi_pin { + pinctrl-single,pins = <0x0a8 0x08>; }; /* lcd_data2.lcd_data2, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ + + /* P8_44 (ZCZ ball R4 ) hdmi */ + P8_44_default_pin: pinmux_P8_44_default_pin { + pinctrl-single,pins = <0x0ac 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_44_gpio_pin: pinmux_P8_44_gpio_pin { + pinctrl-single,pins = <0x0ac 0x2F>; }; /* Mode 7, RxActive */ + P8_44_gpio_pu_pin: pinmux_P8_44_gpio_pu_pin { + pinctrl-single,pins = <0x0ac 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_44_gpio_pd_pin: pinmux_P8_44_gpio_pd_pin { + pinctrl-single,pins = <0x0ac 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_44_pruout_pin: pinmux_P8_44_pruout_pin { + pinctrl-single,pins = <0x0ac 0x05>; }; /* Mode 5, Pull-Down*/ + P8_44_pruin_pin: pinmux_P8_44_pruin_pin { + pinctrl-single,pins = <0x0ac 0x26>; }; /* Mode 6, Pull-Down, RxActive */ + P8_44_pwm_pin: pinmux_P8_44_pwm_pin { + pinctrl-single,pins = <0x0ac 0x23>; }; /* Mode 3, Pull-Down, RxActive */ + P8_44_hdmi_pin: pinmux_P8_44_hdmi_pin { + pinctrl-single,pins = <0x0ac 0x08>; }; /* lcd_data3.lcd_data3, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ + + /* P8_45 (ZCZ ball R1 ) hdmi */ + P8_45_default_pin: pinmux_P8_45_default_pin { + pinctrl-single,pins = <0x0a0 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_45_gpio_pin: pinmux_P8_45_gpio_pin { + pinctrl-single,pins = <0x0a0 0x2F>; }; /* Mode 7, RxActive */ + P8_45_gpio_pu_pin: pinmux_P8_45_gpio_pu_pin { + pinctrl-single,pins = <0x0a0 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_45_gpio_pd_pin: pinmux_P8_45_gpio_pd_pin { + pinctrl-single,pins = <0x0a0 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_45_pruout_pin: pinmux_P8_45_pruout_pin { + pinctrl-single,pins = <0x0a0 0x05>; }; /* Mode 5, Pull-Down*/ + P8_45_pruin_pin: pinmux_P8_45_pruin_pin { + pinctrl-single,pins = <0x0a0 0x26>; }; /* Mode 6, Pull-Down, RxActive */ + P8_45_pwm_pin: pinmux_P8_45_pwm_pin { + pinctrl-single,pins = <0x0a0 0x03>; }; /* Mode 3, Pull-Down*/ + P8_45_hdmi_pin: pinmux_P8_45_hdmi_pin { + pinctrl-single,pins = <0x0a0 0x08>; }; /* lcd_data0.lcd_data0, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ + + /* P8_46 (ZCZ ball R2 ) hdmi */ + P8_46_default_pin: pinmux_P8_46_default_pin { + pinctrl-single,pins = <0x0a4 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_46_gpio_pin: pinmux_P8_46_gpio_pin { + pinctrl-single,pins = <0x0a4 0x2F>; }; /* Mode 7, RxActive */ + P8_46_gpio_pu_pin: pinmux_P8_46_gpio_pu_pin { + pinctrl-single,pins = <0x0a4 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_46_gpio_pd_pin: pinmux_P8_46_gpio_pd_pin { + pinctrl-single,pins = <0x0a4 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_46_pruout_pin: pinmux_P8_46_pruout_pin { + pinctrl-single,pins = <0x0a4 0x05>; }; /* Mode 5, Pull-Down*/ + P8_46_pruin_pin: pinmux_P8_46_pruin_pin { + pinctrl-single,pins = <0x0a4 0x26>; }; /* Mode 6, Pull-Down, RxActive */ + P8_46_pwm_pin: pinmux_P8_46_pwm_pin { + pinctrl-single,pins = <0x0a4 0x03>; }; /* Mode 3, Pull-Down*/ + P8_46_hdmi_pin: pinmux_P8_46_hdmi_pin { + pinctrl-single,pins = <0x0a4 0x08>; }; /* lcd_data1.lcd_data1, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ + + /************************/ + /* P9 Header */ + /************************/ + + /* P9_01 GND */ + /* P9_02 GND */ + /* P9_03 3.3V */ + /* P9_04 3.3V */ + /* P9_05 VDD_5V */ + /* P9_06 VDD_5V */ + /* P9_07 SYS_5V */ + /* P9_08 SYS_5V */ + /* P9_09 PWR_BUT */ + /* P9_10 (ZCZ ball A10) RESETn */ + + /* P9_11 (ZCZ ball T17) */ + P9_11_default_pin: pinmux_P9_11_default_pin { + pinctrl-single,pins = <0x070 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_11_gpio_pin: pinmux_P9_11_gpio_pin { + pinctrl-single,pins = <0x070 0x2F>; }; /* Mode 7, RxActive */ + P9_11_gpio_pu_pin: pinmux_P9_11_gpio_pu_pin { + pinctrl-single,pins = <0x070 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_11_gpio_pd_pin: pinmux_P9_11_gpio_pd_pin { + pinctrl-single,pins = <0x070 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_11_uart_pin: pinmux_P9_11_uart_pin { + pinctrl-single,pins = <0x070 0x36>; }; /* Mode 6, Pull-Up, RxActive */ + + /* P9_12 (ZCZ ball U18) */ + P9_12_default_pin: pinmux_P9_12_default_pin { + pinctrl-single,pins = <0x078 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_12_gpio_pin: pinmux_P9_12_gpio_pin { + pinctrl-single,pins = <0x078 0x2F>; }; /* Mode 7, RxActive */ + P9_12_gpio_pu_pin: pinmux_P9_12_gpio_pu_pin { + pinctrl-single,pins = <0x078 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_12_gpio_pd_pin: pinmux_P9_12_gpio_pd_pin { + pinctrl-single,pins = <0x078 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + + /* P9_13 (ZCZ ball U17) */ + P9_13_default_pin: pinmux_P9_13_default_pin { + pinctrl-single,pins = <0x074 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_13_gpio_pin: pinmux_P9_13_gpio_pin { + pinctrl-single,pins = <0x074 0x2F>; }; /* Mode 7, RxActive */ + P9_13_gpio_pu_pin: pinmux_P9_13_gpio_pu_pin { + pinctrl-single,pins = <0x074 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_13_gpio_pd_pin: pinmux_P9_13_gpio_pd_pin { + pinctrl-single,pins = <0x074 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_13_uart_pin: pinmux_P9_13_uart_pin { + pinctrl-single,pins = <0x074 0x36>; }; /* Mode 6, Pull-Up, RxActive */ + + /* P9_14 (ZCZ ball U14) */ + P9_14_default_pin: pinmux_P9_14_default_pin { + pinctrl-single,pins = <0x048 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_14_gpio_pin: pinmux_P9_14_gpio_pin { + pinctrl-single,pins = <0x048 0x2F>; }; /* Mode 7, RxActive */ + P9_14_gpio_pu_pin: pinmux_P9_14_gpio_pu_pin { + pinctrl-single,pins = <0x048 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_14_gpio_pd_pin: pinmux_P9_14_gpio_pd_pin { + pinctrl-single,pins = <0x048 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_14_pwm_pin: pinmux_P9_14_pwm_pin { + pinctrl-single,pins = <0x048 0x26>; }; /* Mode 6, Pull-Down, RxActive */ + + /* P9_15 (ZCZ ball R13) */ + P9_15_default_pin: pinmux_P9_15_default_pin { + pinctrl-single,pins = <0x040 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_15_gpio_pin: pinmux_P9_15_gpio_pin { + pinctrl-single,pins = <0x040 0x2F>; }; /* Mode 7, RxActive */ + P9_15_gpio_pu_pin: pinmux_P9_15_gpio_pu_pin { + pinctrl-single,pins = <0x040 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_15_gpio_pd_pin: pinmux_P9_15_gpio_pd_pin { + pinctrl-single,pins = <0x040 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_15_pwm_pin: pinmux_P9_15_pwm_pin { + pinctrl-single,pins = <0x040 0x26>; }; /* Mode 6, Pull-Down, RxActive */ + + /* P9_16 (ZCZ ball T14) */ + P9_16_default_pin: pinmux_P9_16_default_pin { + pinctrl-single,pins = <0x04c 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_16_gpio_pin: pinmux_P9_16_gpio_pin { + pinctrl-single,pins = <0x04c 0x2F>; }; /* Mode 7, RxActive */ + P9_16_gpio_pu_pin: pinmux_P9_16_gpio_pu_pin { + pinctrl-single,pins = <0x04c 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_16_gpio_pd_pin: pinmux_P9_16_gpio_pd_pin { + pinctrl-single,pins = <0x04c 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_16_pwm_pin: pinmux_P9_16_pwm_pin { + pinctrl-single,pins = <0x04c 0x26>; }; /* Mode 6, Pull-Down, RxActive */ + + /* P9_17 (ZCZ ball A16) */ + P9_17_default_pin: pinmux_P9_17_default_pin { + pinctrl-single,pins = <0x15c 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_17_gpio_pin: pinmux_P9_17_gpio_pin { + pinctrl-single,pins = <0x15c 0x2F>; }; /* Mode 7, RxActive */ + P9_17_gpio_pu_pin: pinmux_P9_17_gpio_pu_pin { + pinctrl-single,pins = <0x15c 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_17_gpio_pd_pin: pinmux_P9_17_gpio_pd_pin { + pinctrl-single,pins = <0x15c 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_17_spi_pin: pinmux_P9_17_spi_pin { + pinctrl-single,pins = <0x15c 0x30>; }; /* Mode 0, Pull-Up, RxActive */ + P9_17_i2c_pin: pinmux_P9_17_i2c_pin { + pinctrl-single,pins = <0x15c 0x32>; }; /* Mode 2, Pull-Up, RxActive */ + P9_17_pwm_pin: pinmux_P9_17_pwm_pin { + pinctrl-single,pins = <0x15c 0x33>; }; /* Mode 3, Pull-Up, RxActive */ + + /* P9_18 (ZCZ ball B16) */ + P9_18_default_pin: pinmux_P9_18_default_pin { + pinctrl-single,pins = <0x158 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_18_gpio_pin: pinmux_P9_18_gpio_pin { + pinctrl-single,pins = <0x158 0x2F>; }; /* Mode 7, RxActive */ + P9_18_gpio_pu_pin: pinmux_P9_18_gpio_pu_pin { + pinctrl-single,pins = <0x158 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_18_gpio_pd_pin: pinmux_P9_18_gpio_pd_pin { + pinctrl-single,pins = <0x158 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_18_spi_pin: pinmux_P9_18_spi_pin { + pinctrl-single,pins = <0x158 0x30>; }; /* Mode 0, Pull-Up, RxActive */ + P9_18_i2c_pin: pinmux_P9_18_i2c_pin { + pinctrl-single,pins = <0x158 0x32>; }; /* Mode 2, Pull-Up, RxActive */ + P9_18_pwm_pin: pinmux_P9_18_pwm_pin { + pinctrl-single,pins = <0x158 0x33>; }; /* Mode 3, Pull-Up, RxActive */ + + /* P9_19 (ZCZ ball D17) */ + P9_19_default_pin: pinmux_P9_19_default_pin { + pinctrl-single,pins = <0x17c 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_19_gpio_pin: pinmux_P9_19_gpio_pin { + pinctrl-single,pins = <0x17c 0x2F>; }; /* Mode 7, RxActive */ + P9_19_gpio_pu_pin: pinmux_P9_19_gpio_pu_pin { + pinctrl-single,pins = <0x17c 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_19_gpio_pd_pin: pinmux_P9_19_gpio_pd_pin { + pinctrl-single,pins = <0x17c 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_19_can_pin: pinmux_P9_19_can_pin { + pinctrl-single,pins = <0x17c 0x32>; }; /* Mode 2, Pull-Up, RxActive */ + P9_19_i2c_pin: pinmux_P9_19_i2c_pin { + pinctrl-single,pins = <0x17c 0x73>; }; /* (SLEWCTRL_SLOW | PIN_INPUT_PULLUP | MUX_MODE3) */ + + /* P9_20 (ZCZ ball D18) */ + P9_20_default_pin: pinmux_P9_20_default_pin { + pinctrl-single,pins = <0x178 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_20_gpio_pin: pinmux_P9_20_gpio_pin { + pinctrl-single,pins = <0x178 0x2F>; }; /* Mode 7, RxActive */ + P9_20_gpio_pu_pin: pinmux_P9_20_gpio_pu_pin { + pinctrl-single,pins = <0x178 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_20_gpio_pd_pin: pinmux_P9_20_gpio_pd_pin { + pinctrl-single,pins = <0x178 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_20_can_pin: pinmux_P9_20_can_pin { + pinctrl-single,pins = <0x178 0x12>; }; /* Mode 2, Pull-Up, RxActive */ + P9_20_i2c_pin: pinmux_P9_20_i2c_pin { + pinctrl-single,pins = <0x178 0x73>; }; /* (SLEWCTRL_SLOW | PIN_INPUT_PULLUP | MUX_MODE3) */ + + /* P9_21 (ZCZ ball B17) */ + P9_21_default_pin: pinmux_P9_21_default_pin { + pinctrl-single,pins = <0x154 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_21_gpio_pin: pinmux_P9_21_gpio_pin { + pinctrl-single,pins = <0x154 0x2F>; }; /* Mode 7, RxActive */ + P9_21_gpio_pu_pin: pinmux_P9_21_gpio_pu_pin { + pinctrl-single,pins = <0x154 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_21_gpio_pd_pin: pinmux_P9_21_gpio_pd_pin { + pinctrl-single,pins = <0x154 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_21_spi_pin: pinmux_P9_21_spi_pin { + pinctrl-single,pins = <0x154 0x30>; }; /* Mode 0, Pull-Up, RxActive */ + P9_21_uart_pin: pinmux_P9_21_uart_pin { + pinctrl-single,pins = <0x154 0x31>; }; /* Mode 1, Pull-Up, RxActive */ + P9_21_i2c_pin: pinmux_P9_21_i2c_pin { + pinctrl-single,pins = <0x154 0x32>; }; /* Mode 2, Pull-Up, RxActive */ + P9_21_pwm_pin: pinmux_P9_21_pwm_pin { + pinctrl-single,pins = <0x154 0x33>; }; /* Mode 3, Pull-Up, RxActive */ + + /* P9_22 (ZCZ ball A17) */ + P9_22_default_pin: pinmux_P9_22_default_pin { + pinctrl-single,pins = <0x150 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_22_gpio_pin: pinmux_P9_22_gpio_pin { + pinctrl-single,pins = <0x150 0x2F>; }; /* Mode 7, RxActive */ + P9_22_gpio_pu_pin: pinmux_P9_22_gpio_pu_pin { + pinctrl-single,pins = <0x150 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_22_gpio_pd_pin: pinmux_P9_22_gpio_pd_pin { + pinctrl-single,pins = <0x150 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_22_spi_pin: pinmux_P9_22_spi_pin { + pinctrl-single,pins = <0x150 0x30>; }; /* Mode 0, Pull-Up, RxActive */ + P9_22_uart_pin: pinmux_P9_22_uart_pin { + pinctrl-single,pins = <0x150 0x31>; }; /* Mode 1, Pull-Up, RxActive */ + P9_22_i2c_pin: pinmux_P9_22_i2c_pin { + pinctrl-single,pins = <0x150 0x32>; }; /* Mode 2, Pull-Up, RxActive */ + P9_22_pwm_pin: pinmux_P9_22_pwm_pin { + pinctrl-single,pins = <0x150 0x33>; }; /* Mode 3, Pull-Up, RxActive */ + + /* P9_23 (ZCZ ball V14) */ + P9_23_default_pin: pinmux_P9_23_default_pin { + pinctrl-single,pins = <0x044 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_23_gpio_pin: pinmux_P9_23_gpio_pin { + pinctrl-single,pins = <0x044 0x2F>; }; /* Mode 7, RxActive */ + P9_23_gpio_pu_pin: pinmux_P9_23_gpio_pu_pin { + pinctrl-single,pins = <0x044 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_23_gpio_pd_pin: pinmux_P9_23_gpio_pd_pin { + pinctrl-single,pins = <0x044 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_23_pwm_pin: pinmux_P9_23_pwm_pin { + pinctrl-single,pins = <0x044 0x26>; }; /* Mode 6, Pull-Down, RxActive */ + + /* P9_24 (ZCZ ball D15) */ + P9_24_default_pin: pinmux_P9_24_default_pin { + pinctrl-single,pins = <0x184 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_24_gpio_pin: pinmux_P9_24_gpio_pin { + pinctrl-single,pins = <0x184 0x2F>; }; /* Mode 7, RxActive */ + P9_24_gpio_pu_pin: pinmux_P9_24_gpio_pu_pin { + pinctrl-single,pins = <0x184 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_24_gpio_pd_pin: pinmux_P9_24_gpio_pd_pin { + pinctrl-single,pins = <0x184 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_24_uart_pin: pinmux_P9_24_uart_pin { + pinctrl-single,pins = <0x184 0x30>; }; /* Mode 0, Pull-Up, RxActive */ + P9_24_can_pin: pinmux_P9_24_can_pin { + pinctrl-single,pins = <0x184 0x32>; }; /* Mode 2, Pull-Up, RxActive */ + P9_24_i2c_pin: pinmux_P9_24_i2c_pin { + pinctrl-single,pins = <0x184 0x33>; }; /* Mode 3, Pull-Up, RxActive */ + P9_24_pruin_pin: pinmux_P9_24_pruin_pin { + pinctrl-single,pins = <0x184 0x36>; }; /* Mode 6, Pull-Up, RxActive */ + + /* P9_25 (ZCZ ball A14) Audio */ + P9_25_default_pin: pinmux_P9_25_default_pin { + pinctrl-single,pins = <0x1ac 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_25_gpio_pin: pinmux_P9_25_gpio_pin { + pinctrl-single,pins = <0x1ac 0x2F>; }; /* Mode 7, RxActive */ + P9_25_gpio_pu_pin: pinmux_P9_25_gpio_pu_pin { + pinctrl-single,pins = <0x1ac 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_25_gpio_pd_pin: pinmux_P9_25_gpio_pd_pin { + pinctrl-single,pins = <0x1ac 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_25_qep_pin: pinmux_P9_25_qep_pin { + pinctrl-single,pins = <0x1ac 0x21>; }; /* Mode 1, Pull-Down, RxActive */ + P9_25_pruout_pin: pinmux_P9_25_pruout_pin { + pinctrl-single,pins = <0x1ac 0x25>; }; /* Mode 5, Pull-Down, RxActive */ + P9_25_pruin_pin: pinmux_P9_25_pruin_pin { + pinctrl-single,pins = <0x1ac 0x26>; }; /* Mode 6, Pull-Down, RxActive */ + P9_25_audio_pin: pinmux_P9_25_audio_pin { + pinctrl-single,pins = <0x1ac (PIN_INPUT_PULLUP | MUX_MODE0)>; }; /* mcasp0_ahclkx.mcasp0_ahclkx */ + + /* P9_26 (ZCZ ball D16) */ + P9_26_default_pin: pinmux_P9_26_default_pin { + pinctrl-single,pins = <0x180 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_26_gpio_pin: pinmux_P9_26_gpio_pin { + pinctrl-single,pins = <0x180 0x2F>; }; /* Mode 7, RxActive */ + P9_26_gpio_pu_pin: pinmux_P9_26_gpio_pu_pin { + pinctrl-single,pins = <0x180 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_26_gpio_pd_pin: pinmux_P9_26_gpio_pd_pin { + pinctrl-single,pins = <0x180 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_26_uart_pin: pinmux_P9_26_uart_pin { + pinctrl-single,pins = <0x180 0x30>; }; /* Mode 0, Pull-Up, RxActive */ + P9_26_can_pin: pinmux_P9_26_can_pin { + pinctrl-single,pins = <0x180 0x12>; }; /* Mode 2, Pull-Up, RxActive */ + P9_26_i2c_pin: pinmux_P9_26_i2c_pin { + pinctrl-single,pins = <0x180 0x33>; }; /* Mode 3, Pull-Up, RxActive */ + P9_26_pruin_pin: pinmux_P9_26_pruin_pin { + pinctrl-single,pins = <0x180 0x36>; }; /* Mode 6, Pull-Up, RxActive */ + + /* P9_27 (ZCZ ball C13) */ + P9_27_default_pin: pinmux_P9_27_default_pin { + pinctrl-single,pins = <0x1a4 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_27_gpio_pin: pinmux_P9_27_gpio_pin { + pinctrl-single,pins = <0x1a4 0x2F>; }; /* Mode 7, RxActive */ + P9_27_gpio_pu_pin: pinmux_P9_27_gpio_pu_pin { + pinctrl-single,pins = <0x1a4 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_27_gpio_pd_pin: pinmux_P9_27_gpio_pd_pin { + pinctrl-single,pins = <0x1a4 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_27_qep_pin: pinmux_P9_27_qep_pin { + pinctrl-single,pins = <0x1a4 0x21>; }; /* Mode 1, Pull-Down, RxActive */ + P9_27_pruout_pin: pinmux_P9_27_pruout_pin { + pinctrl-single,pins = <0x1a4 0x25>; }; /* Mode 5, Pull-Down, RxActive */ + P9_27_pruin_pin: pinmux_P9_27_pruin_pin { + pinctrl-single,pins = <0x1a4 0x26>; }; /* Mode 6, Pull-Down, RxActive */ + + /* P9_28 (ZCZ ball C12) Audio */ + P9_28_default_pin: pinmux_P9_28_default_pin { + pinctrl-single,pins = <0x19c 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_28_gpio_pin: pinmux_P9_28_gpio_pin { + pinctrl-single,pins = <0x19c 0x2F>; }; /* Mode 7, RxActive */ + P9_28_gpio_pu_pin: pinmux_P9_28_gpio_pu_pin { + pinctrl-single,pins = <0x19c 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_28_gpio_pd_pin: pinmux_P9_28_gpio_pd_pin { + pinctrl-single,pins = <0x19c 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_28_pwm_pin: pinmux_P9_28_pwm_pin { + pinctrl-single,pins = <0x19c 0x21>; }; /* Mode 1, Pull-Down, RxActive */ + P9_28_spi_pin: pinmux_P9_28_spi_pin { + pinctrl-single,pins = <0x19c 0x23>; }; /* Mode 3, Pull-Down, RxActive */ + P9_28_pwm2_pin: pinmux_P9_28_pwm2_pin { + pinctrl-single,pins = <0x19c 0x24>; }; /* Mode 4, Pull-Down, RxActive */ + P9_28_pruout_pin: pinmux_P9_28_pruout_pin { + pinctrl-single,pins = <0x19c 0x25>; }; /* Mode 5, Pull-Down, RxActive */ + P9_28_pruin_pin: pinmux_P9_28_pruin_pin { + pinctrl-single,pins = <0x19c 0x26>; }; /* Mode 6, Pull-Down, RxActive */ + P9_28_audio_pin: pinmux_P9_28_audio_pin { + pinctrl-single,pins = <0x19c (PIN_OUTPUT_PULLDOWN | MUX_MODE2)>; }; /* mcasp0_ahclkr.mcasp0_axr2 */ + + /* P9_29 (ZCZ ball B13) Audio */ + P9_29_default_pin: pinmux_P9_29_default_pin { + pinctrl-single,pins = <0x194 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_29_gpio_pin: pinmux_P9_29_gpio_pin { + pinctrl-single,pins = <0x194 0x2F>; }; /* Mode 7, RxActive */ + P9_29_gpio_pu_pin: pinmux_P9_29_gpio_pu_pin { + pinctrl-single,pins = <0x194 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_29_gpio_pd_pin: pinmux_P9_29_gpio_pd_pin { + pinctrl-single,pins = <0x194 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_29_pwm_pin: pinmux_P9_29_pwm_pin { + pinctrl-single,pins = <0x194 0x21>; }; /* Mode 1, Pull-Down, RxActive */ + P9_29_spi_pin: pinmux_P9_29_spi_pin { + pinctrl-single,pins = <0x194 0x23>; }; /* Mode 3, Pull-Down, RxActive */ + P9_29_pruout_pin: pinmux_P9_29_pruout_pin { + pinctrl-single,pins = <0x194 0x25>; }; /* Mode 5, Pull-Down, RxActive */ + P9_29_pruin_pin: pinmux_P9_29_pruin_pin { + pinctrl-single,pins = <0x194 0x26>; }; /* Mode 6, Pull-Down, RxActive */ + P9_29_audio_pin: pinmux_P9_29_audio_pin { + pinctrl-single,pins = <0x194 (PIN_OUTPUT_PULLUP | MUX_MODE0)>; }; /* mcasp0_fsx.mcasp0_fsx */ + + /* P9_30 (ZCZ ball D12) */ + P9_30_default_pin: pinmux_P9_30_default_pin { + pinctrl-single,pins = <0x198 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_30_gpio_pin: pinmux_P9_30_gpio_pin { + pinctrl-single,pins = <0x198 0x2F>; }; /* Mode 7, RxActive */ + P9_30_gpio_pu_pin: pinmux_P9_30_gpio_pu_pin { + pinctrl-single,pins = <0x198 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_30_gpio_pd_pin: pinmux_P9_30_gpio_pd_pin { + pinctrl-single,pins = <0x198 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_30_pwm_pin: pinmux_P9_30_pwm_pin { + pinctrl-single,pins = <0x198 0x21>; }; /* Mode 1, Pull-Down, RxActive */ + P9_30_spi_pin: pinmux_P9_30_spi_pin { + pinctrl-single,pins = <0x198 0x23>; }; /* Mode 3, Pull-Down, RxActive */ + P9_30_pruout_pin: pinmux_P9_30_pruout_pin { + pinctrl-single,pins = <0x198 0x25>; }; /* Mode 5, Pull-Down, RxActive */ + P9_30_pruin_pin: pinmux_P9_30_pruin_pin { + pinctrl-single,pins = <0x198 0x26>; }; /* Mode 6, Pull-Down, RxActive */ + + /* P9_31 (ZCZ ball A13) Audio */ + P9_31_default_pin: pinmux_P9_31_default_pin { + pinctrl-single,pins = <0x190 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_31_gpio_pin: pinmux_P9_31_gpio_pin { + pinctrl-single,pins = <0x190 0x2F>; }; /* Mode 7, RxActive */ + P9_31_gpio_pu_pin: pinmux_P9_31_gpio_pu_pin { + pinctrl-single,pins = <0x190 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_31_gpio_pd_pin: pinmux_P9_31_gpio_pd_pin { + pinctrl-single,pins = <0x190 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_31_pwm_pin: pinmux_P9_31_pwm_pin { + pinctrl-single,pins = <0x190 0x21>; }; /* Mode 1, Pull-Down, RxActive */ + P9_31_spi_pin: pinmux_P9_31_spi_pin { + pinctrl-single,pins = <0x190 0x23>; }; /* Mode 3, Pull-Down, RxActive */ + P9_31_pruout_pin: pinmux_P9_31_pruout_pin { + pinctrl-single,pins = <0x190 0x25>; }; /* Mode 5, Pull-Down, RxActive */ + P9_31_pruin_pin: pinmux_P9_31_pruin_pin { + pinctrl-single,pins = <0x190 0x26>; }; /* Mode 6, Pull-Down, RxActive */ + P9_31_audio_pin: pinmux_P9_31_audio_pin { + pinctrl-single,pins = <0x190 (PIN_OUTPUT_PULLDOWN | MUX_MODE0)>; }; /* mcasp0_aclkx.mcasp0_aclkx */ + + /* P9_32 VADC */ + /* P9_33 (ZCZ ball C8 ) AIN4 */ + /* P9_34 AGND */ + /* P9_35 (ZCZ ball A8 ) AIN6 */ + /* P9_36 (ZCZ ball B8 ) AIN5 */ + /* P9_37 (ZCZ ball B7 ) AIN2 */ + /* P9_38 (ZCZ ball A7 ) AIN3 */ + /* P9_39 (ZCZ ball B6 ) AIN0 */ + /* P9_40 (ZCZ ball C7 ) AIN1 */ + + /* P9_41 (ZCZ ball D14) */ + P9_41_default_pin: pinmux_P9_41_default_pin { + pinctrl-single,pins = <0x1b4 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_41_gpio_pin: pinmux_P9_41_gpio_pin { + pinctrl-single,pins = <0x1b4 0x2F>; }; /* Mode 7, RxActive */ + P9_41_gpio_pu_pin: pinmux_P9_41_gpio_pu_pin { + pinctrl-single,pins = <0x1b4 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_41_gpio_pd_pin: pinmux_P9_41_gpio_pd_pin { + pinctrl-single,pins = <0x1b4 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_41_timer_pin: pinmux_P9_41_timer_pin { + pinctrl-single,pins = <0x1b4 0x24>; }; /* Mode 4, Pull-Down, RxActive */ + P9_41_pruin_pin: pinmux_P9_41_pruin_pin { + pinctrl-single,pins = <0x1b4 0x25>; }; /* Mode 5, Pull-Down, RxActive */ + + /* P9_41.1 */ + /* P9_91 (ZCZ ball D13) */ + P9_91_default_pin: pinmux_P9_91_default_pin { + pinctrl-single,pins = <0x1a8 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_91_gpio_pin: pinmux_P9_91_gpio_pin { + pinctrl-single,pins = <0x1a8 0x2F>; }; /* Mode 7, RxActive */ + P9_91_gpio_pu_pin: pinmux_P9_91_gpio_pu_pin { + pinctrl-single,pins = <0x1a8 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_91_gpio_pd_pin: pinmux_P9_91_gpio_pd_pin { + pinctrl-single,pins = <0x1a8 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_91_qep_pin: pinmux_P9_91_qep_pin { + pinctrl-single,pins = <0x1a8 0x21>; }; /* Mode 1, Pull-Down, RxActive */ + P9_91_pruout_pin: pinmux_P9_91_pruout_pin { + pinctrl-single,pins = <0x1a8 0x25>; }; /* Mode 5, Pull-Down, RxActive */ + P9_91_pruin_pin: pinmux_P9_91_pruin_pin { + pinctrl-single,pins = <0x1a8 0x26>; }; /* Mode 6, Pull-Down, RxActive */ + + /* P9_42 (ZCZ ball C18) */ + P9_42_default_pin: pinmux_P9_42_default_pin { + pinctrl-single,pins = <0x164 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_42_gpio_pin: pinmux_P9_42_gpio_pin { + pinctrl-single,pins = <0x164 0x2F>; }; /* Mode 7, RxActive */ + P9_42_gpio_pu_pin: pinmux_P9_42_gpio_pu_pin { + pinctrl-single,pins = <0x164 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_42_gpio_pd_pin: pinmux_P9_42_gpio_pd_pin { + pinctrl-single,pins = <0x164 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_42_pwm_pin: pinmux_P9_42_pwm_pin { + pinctrl-single,pins = <0x164 0x20>; }; /* Mode 0, Pull-Down, RxActive */ + P9_42_uart_pin: pinmux_P9_42_uart_pin { + pinctrl-single,pins = <0x164 0x21>; }; /* Mode 1, Pull-Down, RxActive */ + P9_42_spics_pin: pinmux_P9_42_spics_pin { + pinctrl-single,pins = <0x164 0x22>; }; /* Mode 2, Pull-Down, RxActive */ + P9_42_spiclk_pin: pinmux_P9_42_spiclk_pin { + pinctrl-single,pins = <0x164 0x24>; }; /* Mode 4, Pull-Down, RxActive */ + + /* P9_42.1 */ + /* P9_92 (ZCZ ball B12) */ + P9_92_default_pin: pinmux_P9_92_default_pin { + pinctrl-single,pins = <0x1a0 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_92_gpio_pin: pinmux_P9_92_gpio_pin { + pinctrl-single,pins = <0x1a0 0x2F>; }; /* Mode 7, RxActive */ + P9_92_gpio_pu_pin: pinmux_P9_92_gpio_pu_pin { + pinctrl-single,pins = <0x1a0 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_92_gpio_pd_pin: pinmux_P9_92_gpio_pd_pin { + pinctrl-single,pins = <0x1a0 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_92_qep_pin: pinmux_P9_92_qep_pin { + pinctrl-single,pins = <0x1a0 0x21>; }; /* Mode 1, Pull-Down, RxActive */ + P9_92_pruout_pin: pinmux_P9_92_pruout_pin { + pinctrl-single,pins = <0x1a0 0x25>; }; /* Mode 5, Pull-Down, RxActive */ + P9_92_pruin_pin: pinmux_P9_92_pruin_pin { + pinctrl-single,pins = <0x1a0 0x26>; }; /* Mode 6, Pull-Down, RxActive */ + + /* P9_43 GND */ + /* P9_44 GND */ + /* P9_45 GND */ + /* P9_46 GND */ +}; diff --git b/arch/arm/boot/dts/am335x-bone-common-universal.dtsi b/arch/arm/boot/dts/am335x-bone-common-universal.dtsi new file mode 100644 index 000000000..781e33fe3 --- /dev/null +++ b/arch/arm/boot/dts/am335x-bone-common-universal.dtsi @@ -0,0 +1,2052 @@ +/* + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +&am33xx_pinmux { + /************************/ + /* P8 Header */ + /************************/ + + /* P8_01 GND */ + /* P8_02 GND */ + /* P8_03 (ZCZ ball R9 ) emmc */ + /* P8_04 (ZCZ ball T9 ) emmc */ + /* P8_05 (ZCZ ball R8 ) emmc */ + /* P8_06 (ZCZ ball T8 ) emmc */ + + /* P8_07 (ZCZ ball R7 ) */ + P8_07_default_pin: pinmux_P8_07_default_pin { + pinctrl-single,pins = <0x090 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_07_gpio_pin: pinmux_P8_07_gpio_pin { + pinctrl-single,pins = <0x090 0x2F>; }; /* Mode 7, RxActive */ + P8_07_gpio_pu_pin: pinmux_P8_07_gpio_pu_pin { + pinctrl-single,pins = <0x090 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_07_gpio_pd_pin: pinmux_P8_07_gpio_pd_pin { + pinctrl-single,pins = <0x090 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_07_timer_pin: pinmux_P8_07_timer_pin { + pinctrl-single,pins = <0x090 0x32>; }; /* Mode 2, Pull-Up, RxActive */ + + /* P8_08 (ZCZ ball T7 ) */ + P8_08_default_pin: pinmux_P8_08_default_pin { + pinctrl-single,pins = <0x094 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_08_gpio_pin: pinmux_P8_08_gpio_pin { + pinctrl-single,pins = <0x094 0x2F>; }; /* Mode 7, RxActive */ + P8_08_gpio_pu_pin: pinmux_P8_08_gpio_pu_pin { + pinctrl-single,pins = <0x094 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_08_gpio_pd_pin: pinmux_P8_08_gpio_pd_pin { + pinctrl-single,pins = <0x094 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_08_timer_pin: pinmux_P8_08_timer_pin { + pinctrl-single,pins = <0x094 0x32>; }; /* Mode 2, Pull-Up, RxActive */ + + /* P8_09 (ZCZ ball T6 ) */ + P8_09_default_pin: pinmux_P8_09_default_pin { + pinctrl-single,pins = <0x09c 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_09_gpio_pin: pinmux_P8_09_gpio_pin { + pinctrl-single,pins = <0x09c 0x2F>; }; /* Mode 7, RxActive */ + P8_09_gpio_pu_pin: pinmux_P8_09_gpio_pu_pin { + pinctrl-single,pins = <0x09c 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_09_gpio_pd_pin: pinmux_P8_09_gpio_pd_pin { + pinctrl-single,pins = <0x09c 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_09_timer_pin: pinmux_P8_09_timer_pin { + pinctrl-single,pins = <0x09c 0x32>; }; /* Mode 2, Pull-Up, RxActive */ + + /* P8_10 (ZCZ ball U6 ) */ + P8_10_default_pin: pinmux_P8_10_default_pin { + pinctrl-single,pins = <0x098 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_10_gpio_pin: pinmux_P8_10_gpio_pin { + pinctrl-single,pins = <0x098 0x2F>; }; /* Mode 7, RxActive */ + P8_10_gpio_pu_pin: pinmux_P8_10_gpio_pu_pin { + pinctrl-single,pins = <0x098 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_10_gpio_pd_pin: pinmux_P8_10_gpio_pd_pin { + pinctrl-single,pins = <0x098 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_10_timer_pin: pinmux_P8_10_timer_pin { + pinctrl-single,pins = <0x098 0x32>; }; /* Mode 2, Pull-Up, RxActive */ + + /* P8_11 (ZCZ ball R12) */ + P8_11_default_pin: pinmux_P8_11_default_pin { + pinctrl-single,pins = <0x034 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_11_gpio_pin: pinmux_P8_11_gpio_pin { + pinctrl-single,pins = <0x034 0x2F>; }; /* Mode 7, RxActive */ + P8_11_gpio_pu_pin: pinmux_P8_11_gpio_pu_pin { + pinctrl-single,pins = <0x034 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_11_gpio_pd_pin: pinmux_P8_11_gpio_pd_pin { + pinctrl-single,pins = <0x034 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_11_pruout_pin: pinmux_P8_11_pruout_pin { + pinctrl-single,pins = <0x034 0x26>; }; /* Mode 6, Pull-Down, RxActive */ + P8_11_qep_pin: pinmux_P8_11_qep_pin { + pinctrl-single,pins = <0x034 0x24>; }; /* Mode 4, Pull-Down, RxActive */ + + /* P8_12 (ZCZ ball T12) */ + P8_12_default_pin: pinmux_P8_12_default_pin { + pinctrl-single,pins = <0x030 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_12_gpio_pin: pinmux_P8_12_gpio_pin { + pinctrl-single,pins = <0x030 0x2F>; }; /* Mode 7, RxActive */ + P8_12_gpio_pu_pin: pinmux_P8_12_gpio_pu_pin { + pinctrl-single,pins = <0x030 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_12_gpio_pd_pin: pinmux_P8_12_gpio_pd_pin { + pinctrl-single,pins = <0x030 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_12_pruout_pin: pinmux_P8_12_pruout_pin { + pinctrl-single,pins = <0x030 0x26>; }; /* Mode 6, Pull-Down, RxActive */ + P8_12_qep_pin: pinmux_P8_12_qep_pin { + pinctrl-single,pins = <0x030 0x24>; }; /* Mode 4, Pull-Down, RxActive */ + + /* P8_13 (ZCZ ball T10) */ + P8_13_default_pin: pinmux_P8_13_default_pin { + pinctrl-single,pins = <0x024 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_13_gpio_pin: pinmux_P8_13_gpio_pin { + pinctrl-single,pins = <0x024 0x2F>; }; /* Mode 7, RxActive */ + P8_13_gpio_pu_pin: pinmux_P8_13_gpio_pu_pin { + pinctrl-single,pins = <0x024 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_13_gpio_pd_pin: pinmux_P8_13_gpio_pd_pin { + pinctrl-single,pins = <0x024 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_13_pwm_pin: pinmux_P8_13_pwm_pin { + pinctrl-single,pins = <0x024 0x24>; }; /* Mode 4, Pull-Down, RxActive */ + + /* P8_14 (ZCZ ball T11) */ + P8_14_default_pin: pinmux_P8_14_default_pin { + pinctrl-single,pins = <0x028 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_14_gpio_pin: pinmux_P8_14_gpio_pin { + pinctrl-single,pins = <0x028 0x2F>; }; /* Mode 7, RxActive */ + P8_14_gpio_pu_pin: pinmux_P8_14_gpio_pu_pin { + pinctrl-single,pins = <0x028 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_14_gpio_pd_pin: pinmux_P8_14_gpio_pd_pin { + pinctrl-single,pins = <0x028 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_14_pwm_pin: pinmux_P8_14_pwm_pin { + pinctrl-single,pins = <0x028 0x24>; }; /* Mode 4, Pull-Down, RxActive */ + + /* P8_15 (ZCZ ball U13) */ + P8_15_default_pin: pinmux_P8_15_default_pin { + pinctrl-single,pins = <0x03c 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_15_gpio_pin: pinmux_P8_15_gpio_pin { + pinctrl-single,pins = <0x03c 0x2F>; }; /* Mode 7, RxActive */ + P8_15_gpio_pu_pin: pinmux_P8_15_gpio_pu_pin { + pinctrl-single,pins = <0x03c 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_15_gpio_pd_pin: pinmux_P8_15_gpio_pd_pin { + pinctrl-single,pins = <0x03c 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_15_pruin_pin: pinmux_P8_15_pruin_pin { + pinctrl-single,pins = <0x03c 0x26>; }; /* Mode 6, Pull-Down, RxActive */ + P8_15_qep_pin: pinmux_P8_15_qep_pin { + pinctrl-single,pins = <0x03c 0x24>; }; /* Mode 4, Pull-Down, RxActive */ + + /* P8_16 (ZCZ ball V13) */ + P8_16_default_pin: pinmux_P8_16_default_pin { + pinctrl-single,pins = <0x038 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_16_gpio_pin: pinmux_P8_16_gpio_pin { + pinctrl-single,pins = <0x038 0x2F>; }; /* Mode 7, RxActive */ + P8_16_gpio_pu_pin: pinmux_P8_16_gpio_pu_pin { + pinctrl-single,pins = <0x038 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_16_gpio_pd_pin: pinmux_P8_16_gpio_pd_pin { + pinctrl-single,pins = <0x038 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_16_pruin_pin: pinmux_P8_16_pruin_pin { + pinctrl-single,pins = <0x038 0x26>; }; /* Mode 6, Pull-Down, RxActive */ + P8_16_qep_pin: pinmux_P8_16_qep_pin { + pinctrl-single,pins = <0x038 0x24>; }; /* Mode 4, Pull-Down, RxActive */ + + /* P8_17 (ZCZ ball U12) */ + P8_17_default_pin: pinmux_P8_17_default_pin { + pinctrl-single,pins = <0x02c 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_17_gpio_pin: pinmux_P8_17_gpio_pin { + pinctrl-single,pins = <0x02c 0x2F>; }; /* Mode 7, RxActive */ + P8_17_gpio_pu_pin: pinmux_P8_17_gpio_pu_pin { + pinctrl-single,pins = <0x02c 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_17_gpio_pd_pin: pinmux_P8_17_gpio_pd_pin { + pinctrl-single,pins = <0x02c 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_17_pwm_pin: pinmux_P8_17_pwm_pin { + pinctrl-single,pins = <0x02c 0x24>; }; /* Mode 4, Pull-Down, RxActive */ + + /* P8_18 (ZCZ ball V12) */ + P8_18_default_pin: pinmux_P8_18_default_pin { + pinctrl-single,pins = <0x08c 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_18_gpio_pin: pinmux_P8_18_gpio_pin { + pinctrl-single,pins = <0x08c 0x2F>; }; /* Mode 7, RxActive */ + P8_18_gpio_pu_pin: pinmux_P8_18_gpio_pu_pin { + pinctrl-single,pins = <0x08c 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_18_gpio_pd_pin: pinmux_P8_18_gpio_pd_pin { + pinctrl-single,pins = <0x08c 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + + /* P8_19 (ZCZ ball U10) */ + P8_19_default_pin: pinmux_P8_19_default_pin { + pinctrl-single,pins = <0x020 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_19_gpio_pin: pinmux_P8_19_gpio_pin { + pinctrl-single,pins = <0x020 0x2F>; }; /* Mode 7, RxActive */ + P8_19_gpio_pu_pin: pinmux_P8_19_gpio_pu_pin { + pinctrl-single,pins = <0x020 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_19_gpio_pd_pin: pinmux_P8_19_gpio_pd_pin { + pinctrl-single,pins = <0x020 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_19_pwm_pin: pinmux_P8_19_pwm_pin { + pinctrl-single,pins = <0x020 0x24>; }; /* Mode 4, Pull-Down, RxActive */ + + /* P8_20 (ZCZ ball V9 ) emmc */ + /* P8_21 (ZCZ ball U9 ) emmc */ + /* P8_22 (ZCZ ball V8 ) emmc */ + /* P8_23 (ZCZ ball U8 ) emmc */ + /* P8_24 (ZCZ ball V7 ) emmc */ + /* P8_25 (ZCZ ball U7 ) emmc */ + + /* P8_26 (ZCZ ball V6 ) */ + P8_26_default_pin: pinmux_P8_26_default_pin { + pinctrl-single,pins = <0x07c 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_26_gpio_pin: pinmux_P8_26_gpio_pin { + pinctrl-single,pins = <0x07c 0x2F>; }; /* Mode 7, RxActive */ + P8_26_gpio_pu_pin: pinmux_P8_26_gpio_pu_pin { + pinctrl-single,pins = <0x07c 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_26_gpio_pd_pin: pinmux_P8_26_gpio_pd_pin { + pinctrl-single,pins = <0x07c 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + + /* P8_27 (ZCZ ball U5 ) hdmi */ + P8_27_default_pin: pinmux_P8_27_default_pin { + pinctrl-single,pins = <0x0e0 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_27_gpio_pin: pinmux_P8_27_gpio_pin { + pinctrl-single,pins = <0x0e0 0x2F>; }; /* Mode 7, RxActive */ + P8_27_gpio_pu_pin: pinmux_P8_27_gpio_pu_pin { + pinctrl-single,pins = <0x0e0 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_27_gpio_pd_pin: pinmux_P8_27_gpio_pd_pin { + pinctrl-single,pins = <0x0e0 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_27_pruout_pin: pinmux_P8_27_pruout_pin { + pinctrl-single,pins = <0x0e0 0x05>; }; /* Mode 5, Pull-Down*/ + P8_27_pruin_pin: pinmux_P8_27_pruin_pin { + pinctrl-single,pins = <0x0e0 0x26>; }; /* Mode 6, Pull-Down, RxActive */ + P8_27_hdmi_pin: pinmux_P8_27_hdmi_pin { + pinctrl-single,pins = <0x0e0 0x00>; }; /* lcd_vsync.lcd_vsync, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT */ + + /* P8_28 (ZCZ ball V5 ) hdmi */ + P8_28_default_pin: pinmux_P8_28_default_pin { + pinctrl-single,pins = <0x0e8 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_28_gpio_pin: pinmux_P8_28_gpio_pin { + pinctrl-single,pins = <0x0e8 0x2F>; }; /* Mode 7, RxActive */ + P8_28_gpio_pu_pin: pinmux_P8_28_gpio_pu_pin { + pinctrl-single,pins = <0x0e8 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_28_gpio_pd_pin: pinmux_P8_28_gpio_pd_pin { + pinctrl-single,pins = <0x0e8 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_28_pruout_pin: pinmux_P8_28_pruout_pin { + pinctrl-single,pins = <0x0e8 0x05>; }; /* Mode 5, Pull-Down */ + P8_28_pruin_pin: pinmux_P8_28_pruin_pin { + pinctrl-single,pins = <0x0e8 0x26>; }; /* Mode 6, Pull-Down, RxActive */ + P8_28_hdmi_pin: pinmux_P8_28_hdmi_pin { + pinctrl-single,pins = <0x0e8 0x00>; }; /* lcd_pclk.lcd_pclk, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT */ + + /* P8_29 (ZCZ ball R5 ) hdmi */ + P8_29_default_pin: pinmux_P8_29_default_pin { + pinctrl-single,pins = <0x0e4 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_29_gpio_pin: pinmux_P8_29_gpio_pin { + pinctrl-single,pins = <0x0e4 0x2F>; }; /* Mode 7, RxActive */ + P8_29_gpio_pu_pin: pinmux_P8_29_gpio_pu_pin { + pinctrl-single,pins = <0x0e4 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_29_gpio_pd_pin: pinmux_P8_29_gpio_pd_pin { + pinctrl-single,pins = <0x0e4 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_29_pruout_pin: pinmux_P8_29_pruout_pin { + pinctrl-single,pins = <0x0e4 0x05>; }; /* Mode 5, Pull-Down*/ + P8_29_pruin_pin: pinmux_P8_29_pruin_pin { + pinctrl-single,pins = <0x0e4 0x26>; }; /* Mode 6, Pull-Down, RxActive */ + P8_29_hdmi_pin: pinmux_P8_29_hdmi_pin { + pinctrl-single,pins = <0x0e4 0x00>; }; /* lcd_hsync.lcd_hsync, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT */ + + /* P8_30 (ZCZ ball R6 ) hdmi */ + P8_30_default_pin: pinmux_P8_30_default_pin { + pinctrl-single,pins = <0x0ec 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_30_gpio_pin: pinmux_P8_30_gpio_pin { + pinctrl-single,pins = <0x0ec 0x2F>; }; /* Mode 7, RxActive */ + P8_30_gpio_pu_pin: pinmux_P8_30_gpio_pu_pin { + pinctrl-single,pins = <0x0ec 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_30_gpio_pd_pin: pinmux_P8_30_gpio_pd_pin { + pinctrl-single,pins = <0x0ec 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_30_pruout_pin: pinmux_P8_30_pruout_pin { + pinctrl-single,pins = <0x0ec 0x05>; }; /* Mode 5, Pull-Down*/ + P8_30_pruin_pin: pinmux_P8_30_pruin_pin { + pinctrl-single,pins = <0x0ec 0x26>; }; /* Mode 6, Pull-Down, RxActive */ + P8_30_hdmi_pin: pinmux_P8_30_hdmi_pin { + pinctrl-single,pins = <0x0ec 0x00>; }; /* lcd_ac_bias_en.lcd_ac_bias_en, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT */ + + /* P8_31 (ZCZ ball V4 ) hdmi */ + P8_31_default_pin: pinmux_P8_31_default_pin { + pinctrl-single,pins = <0x0d8 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_31_gpio_pin: pinmux_P8_31_gpio_pin { + pinctrl-single,pins = <0x0d8 0x2F>; }; /* Mode 7, RxActive */ + P8_31_gpio_pu_pin: pinmux_P8_31_gpio_pu_pin { + pinctrl-single,pins = <0x0d8 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_31_gpio_pd_pin: pinmux_P8_31_gpio_pd_pin { + pinctrl-single,pins = <0x0d8 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_31_uart_pin: pinmux_P8_31_uart_pin { + pinctrl-single,pins = <0x0d8 0x24>; }; /* Mode 4, Pull-Down, RxActive */ + P8_31_hdmi_pin: pinmux_P8_31_hdmi_pin { + pinctrl-single,pins = <0x0d8 0x08>; }; /* lcd_data14.lcd_data14, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ + + /* P8_32 (ZCZ ball T5 ) hdmi */ + P8_32_default_pin: pinmux_P8_32_default_pin { + pinctrl-single,pins = <0x0dc 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_32_gpio_pin: pinmux_P8_32_gpio_pin { + pinctrl-single,pins = <0x0dc 0x2F>; }; /* Mode 7, RxActive */ + P8_32_gpio_pu_pin: pinmux_P8_32_gpio_pu_pin { + pinctrl-single,pins = <0x0dc 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_32_gpio_pd_pin: pinmux_P8_32_gpio_pd_pin { + pinctrl-single,pins = <0x0dc 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_32_uart_pin: pinmux_P8_32_uart_pin { + pinctrl-single,pins = <0x0dc 0x26>; }; /* Mode 6, Pull-Down, RxActive */ + P8_32_hdmi_pin: pinmux_P8_32_hdmi_pin { + pinctrl-single,pins = <0x0dc 0x08>; }; /* lcd_data15.lcd_data15, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ + + /* P8_33 (ZCZ ball V3 ) hdmi */ + P8_33_default_pin: pinmux_P8_33_default_pin { + pinctrl-single,pins = <0x0d4 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_33_gpio_pin: pinmux_P8_33_gpio_pin { + pinctrl-single,pins = <0x0d4 0x2F>; }; /* Mode 7, RxActive */ + P8_33_gpio_pu_pin: pinmux_P8_33_gpio_pu_pin { + pinctrl-single,pins = <0x0d4 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_33_gpio_pd_pin: pinmux_P8_33_gpio_pd_pin { + pinctrl-single,pins = <0x0d4 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_33_hdmi_pin: pinmux_P8_33_hdmi_pin { + pinctrl-single,pins = <0x0d4 0x08>; }; /* lcd_data13.lcd_data13, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ + + /* P8_34 (ZCZ ball U4 ) hdmi */ + P8_34_default_pin: pinmux_P8_34_default_pin { + pinctrl-single,pins = <0x0cc 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_34_gpio_pin: pinmux_P8_34_gpio_pin { + pinctrl-single,pins = <0x0cc 0x2F>; }; /* Mode 7, RxActive */ + P8_34_gpio_pu_pin: pinmux_P8_34_gpio_pu_pin { + pinctrl-single,pins = <0x0cc 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_34_gpio_pd_pin: pinmux_P8_34_gpio_pd_pin { + pinctrl-single,pins = <0x0cc 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_34_pwm_pin: pinmux_P8_34_pwm_pin { + pinctrl-single,pins = <0x0cc 0x22>; }; /* Mode 2, Pull-Down, RxActive */ + P8_34_hdmi_pin: pinmux_P8_34_hdmi_pin { + pinctrl-single,pins = <0x0cc 0x08>; }; /* lcd_data11.lcd_data11, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ + + /* P8_35 (ZCZ ball V2 ) hdmi */ + P8_35_default_pin: pinmux_P8_35_default_pin { + pinctrl-single,pins = <0x0d0 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_35_gpio_pin: pinmux_P8_35_gpio_pin { + pinctrl-single,pins = <0x0d0 0x2F>; }; /* Mode 7, RxActive */ + P8_35_gpio_pu_pin: pinmux_P8_35_gpio_pu_pin { + pinctrl-single,pins = <0x0d0 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_35_gpio_pd_pin: pinmux_P8_35_gpio_pd_pin { + pinctrl-single,pins = <0x0d0 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_35_hdmi_pin: pinmux_P8_35_hdmi_pin { + pinctrl-single,pins = <0x0d0 0x08>; }; /* lcd_data12.lcd_data12, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ + + /* P8_36 (ZCZ ball U3 ) hdmi */ + P8_36_default_pin: pinmux_P8_36_default_pin { + pinctrl-single,pins = <0x0c8 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_36_gpio_pin: pinmux_P8_36_gpio_pin { + pinctrl-single,pins = <0x0c8 0x2F>; }; /* Mode 7, RxActive */ + P8_36_gpio_pu_pin: pinmux_P8_36_gpio_pu_pin { + pinctrl-single,pins = <0x0c8 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_36_gpio_pd_pin: pinmux_P8_36_gpio_pd_pin { + pinctrl-single,pins = <0x0c8 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_36_pwm_pin: pinmux_P8_36_pwm_pin { + pinctrl-single,pins = <0x0c8 0x22>; }; /* Mode 2, Pull-Down, RxActive */ + P8_36_hdmi_pin: pinmux_P8_36_hdmi_pin { + pinctrl-single,pins = <0x0c8 0x08>; }; /* lcd_data10.lcd_data10, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ + + /* P8_37 (ZCZ ball U1 ) hdmi */ + P8_37_default_pin: pinmux_P8_37_default_pin { + pinctrl-single,pins = <0x0c0 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_37_gpio_pin: pinmux_P8_37_gpio_pin { + pinctrl-single,pins = <0x0c0 0x2F>; }; /* Mode 7, RxActive */ + P8_37_gpio_pu_pin: pinmux_P8_37_gpio_pu_pin { + pinctrl-single,pins = <0x0c0 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_37_gpio_pd_pin: pinmux_P8_37_gpio_pd_pin { + pinctrl-single,pins = <0x0c0 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_37_uart_pin: pinmux_P8_37_uart_pin { + pinctrl-single,pins = <0x0c0 0x04>; }; /* Mode 4, Pull-Down*/ + P8_37_pwm_pin: pinmux_P8_37_pwm_pin { + pinctrl-single,pins = <0x0c0 0x02>; }; /* Mode 2, Pull-Down*/ + P8_37_hdmi_pin: pinmux_P8_37_hdmi_pin { + pinctrl-single,pins = <0x0c0 0x08>; }; /* lcd_data8.lcd_data8, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ + + + /* P8_38 (ZCZ ball U2 ) hdmi */ + P8_38_default_pin: pinmux_P8_38_default_pin { + pinctrl-single,pins = <0x0c4 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_38_gpio_pin: pinmux_P8_38_gpio_pin { + pinctrl-single,pins = <0x0c4 0x2F>; }; /* Mode 7, RxActive */ + P8_38_gpio_pu_pin: pinmux_P8_38_gpio_pu_pin { + pinctrl-single,pins = <0x0c4 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_38_gpio_pd_pin: pinmux_P8_38_gpio_pd_pin { + pinctrl-single,pins = <0x0c4 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_38_uart_pin: pinmux_P8_38_uart_pin { + pinctrl-single,pins = <0x0c4 0x24>; }; /* Mode 4, Pull-Down, RxActive */ + P8_38_pwm_pin: pinmux_P8_38_pwm_pin { + pinctrl-single,pins = <0x0c4 0x22>; }; /* Mode 2, Pull-Down, RxActive */ + P8_38_hdmi_pin: pinmux_P8_38_hdmi_pin { + pinctrl-single,pins = <0x0c4 0x08>; }; /* lcd_data9.lcd_data9, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ + + + /* P8_39 (ZCZ ball T3 ) hdmi */ + P8_39_default_pin: pinmux_P8_39_default_pin { + pinctrl-single,pins = <0x0b8 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_39_gpio_pin: pinmux_P8_39_gpio_pin { + pinctrl-single,pins = <0x0b8 0x2F>; }; /* Mode 7, RxActive */ + P8_39_gpio_pu_pin: pinmux_P8_39_gpio_pu_pin { + pinctrl-single,pins = <0x0b8 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_39_gpio_pd_pin: pinmux_P8_39_gpio_pd_pin { + pinctrl-single,pins = <0x0b8 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_39_pruout_pin: pinmux_P8_39_pruout_pin { + pinctrl-single,pins = <0x0b8 0x05>; }; /* Mode 5, Pull-Down*/ + P8_39_pruin_pin: pinmux_P8_39_pruin_pin { + pinctrl-single,pins = <0x0b8 0x26>; }; /* Mode 6, Pull-Down, RxActive */ + P8_39_hdmi_pin: pinmux_P8_39_hdmi_pin { + pinctrl-single,pins = <0x0b8 0x08>; }; /* lcd_data6.lcd_data6, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ + + /* P8_40 (ZCZ ball T4 ) hdmi */ + P8_40_default_pin: pinmux_P8_40_default_pin { + pinctrl-single,pins = <0x0bc 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_40_gpio_pin: pinmux_P8_40_gpio_pin { + pinctrl-single,pins = <0x0bc 0x2F>; }; /* Mode 7, RxActive */ + P8_40_gpio_pu_pin: pinmux_P8_40_gpio_pu_pin { + pinctrl-single,pins = <0x0bc 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_40_gpio_pd_pin: pinmux_P8_40_gpio_pd_pin { + pinctrl-single,pins = <0x0bc 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_40_pruout_pin: pinmux_P8_40_pruout_pin { + pinctrl-single,pins = <0x0bc 0x05>; }; /* Mode 5, Pull-Down*/ + P8_40_pruin_pin: pinmux_P8_40_pruin_pin { + pinctrl-single,pins = <0x0bc 0x26>; }; /* Mode 6, Pull-Down, RxActive */ + P8_40_hdmi_pin: pinmux_P8_40_hdmi_pin { + pinctrl-single,pins = <0x0bc 0x08>; }; /* lcd_data7.lcd_data7, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ + + /* P8_41 (ZCZ ball T1 ) hdmi */ + P8_41_default_pin: pinmux_P8_41_default_pin { + pinctrl-single,pins = <0x0b0 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_41_gpio_pin: pinmux_P8_41_gpio_pin { + pinctrl-single,pins = <0x0b0 0x2F>; }; /* Mode 7, RxActive */ + P8_41_gpio_pu_pin: pinmux_P8_41_gpio_pu_pin { + pinctrl-single,pins = <0x0b0 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_41_gpio_pd_pin: pinmux_P8_41_gpio_pd_pin { + pinctrl-single,pins = <0x0b0 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_41_pruout_pin: pinmux_P8_41_pruout_pin { + pinctrl-single,pins = <0x0b0 0x05>; }; /* Mode 5, Pull-Down*/ + P8_41_pruin_pin: pinmux_P8_41_pruin_pin { + pinctrl-single,pins = <0x0b0 0x26>; }; /* Mode 6, Pull-Down, RxActive */ + P8_41_hdmi_pin: pinmux_P8_41_hdmi_pin { + pinctrl-single,pins = <0x0b0 0x08>; }; /* lcd_data4.lcd_data4, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ + + /* P8_42 (ZCZ ball T2 ) hdmi */ + P8_42_default_pin: pinmux_P8_42_default_pin { + pinctrl-single,pins = <0x0b4 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_42_gpio_pin: pinmux_P8_42_gpio_pin { + pinctrl-single,pins = <0x0b4 0x2F>; }; /* Mode 7, RxActive */ + P8_42_gpio_pu_pin: pinmux_P8_42_gpio_pu_pin { + pinctrl-single,pins = <0x0b4 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_42_gpio_pd_pin: pinmux_P8_42_gpio_pd_pin { + pinctrl-single,pins = <0x0b4 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_42_pruout_pin: pinmux_P8_42_pruout_pin { + pinctrl-single,pins = <0x0b4 0x05>; }; /* Mode 5, Pull-Down*/ + P8_42_pruin_pin: pinmux_P8_42_pruin_pin { + pinctrl-single,pins = <0x0b4 0x26>; }; /* Mode 6, Pull-Down, RxActive */ + P8_42_hdmi_pin: pinmux_P8_42_hdmi_pin { + pinctrl-single,pins = <0x0b4 0x08>; }; /* lcd_data5.lcd_data5, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ + + /* P8_43 (ZCZ ball R3 ) hdmi */ + P8_43_default_pin: pinmux_P8_43_default_pin { + pinctrl-single,pins = <0x0a8 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_43_gpio_pin: pinmux_P8_43_gpio_pin { + pinctrl-single,pins = <0x0a8 0x2F>; }; /* Mode 7, RxActive */ + P8_43_gpio_pu_pin: pinmux_P8_43_gpio_pu_pin { + pinctrl-single,pins = <0x0a8 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_43_gpio_pd_pin: pinmux_P8_43_gpio_pd_pin { + pinctrl-single,pins = <0x0a8 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_43_pruout_pin: pinmux_P8_43_pruout_pin { + pinctrl-single,pins = <0x0a8 0x05>; }; /* Mode 5, Pull-Down*/ + P8_43_pruin_pin: pinmux_P8_43_pruin_pin { + pinctrl-single,pins = <0x0a8 0x26>; }; /* Mode 6, Pull-Down, RxActive */ + P8_43_pwm_pin: pinmux_P8_43_pwm_pin { + pinctrl-single,pins = <0x0a8 0x03>; }; /* Mode 3, Pull-Down */ + P8_43_hdmi_pin: pinmux_P8_43_hdmi_pin { + pinctrl-single,pins = <0x0a8 0x08>; }; /* lcd_data2.lcd_data2, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ + + /* P8_44 (ZCZ ball R4 ) hdmi */ + P8_44_default_pin: pinmux_P8_44_default_pin { + pinctrl-single,pins = <0x0ac 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_44_gpio_pin: pinmux_P8_44_gpio_pin { + pinctrl-single,pins = <0x0ac 0x2F>; }; /* Mode 7, RxActive */ + P8_44_gpio_pu_pin: pinmux_P8_44_gpio_pu_pin { + pinctrl-single,pins = <0x0ac 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_44_gpio_pd_pin: pinmux_P8_44_gpio_pd_pin { + pinctrl-single,pins = <0x0ac 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_44_pruout_pin: pinmux_P8_44_pruout_pin { + pinctrl-single,pins = <0x0ac 0x05>; }; /* Mode 5, Pull-Down*/ + P8_44_pruin_pin: pinmux_P8_44_pruin_pin { + pinctrl-single,pins = <0x0ac 0x26>; }; /* Mode 6, Pull-Down, RxActive */ + P8_44_pwm_pin: pinmux_P8_44_pwm_pin { + pinctrl-single,pins = <0x0ac 0x23>; }; /* Mode 3, Pull-Down, RxActive */ + P8_44_hdmi_pin: pinmux_P8_44_hdmi_pin { + pinctrl-single,pins = <0x0ac 0x08>; }; /* lcd_data3.lcd_data3, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ + + /* P8_45 (ZCZ ball R1 ) hdmi */ + P8_45_default_pin: pinmux_P8_45_default_pin { + pinctrl-single,pins = <0x0a0 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_45_gpio_pin: pinmux_P8_45_gpio_pin { + pinctrl-single,pins = <0x0a0 0x2F>; }; /* Mode 7, RxActive */ + P8_45_gpio_pu_pin: pinmux_P8_45_gpio_pu_pin { + pinctrl-single,pins = <0x0a0 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_45_gpio_pd_pin: pinmux_P8_45_gpio_pd_pin { + pinctrl-single,pins = <0x0a0 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_45_pruout_pin: pinmux_P8_45_pruout_pin { + pinctrl-single,pins = <0x0a0 0x05>; }; /* Mode 5, Pull-Down*/ + P8_45_pruin_pin: pinmux_P8_45_pruin_pin { + pinctrl-single,pins = <0x0a0 0x26>; }; /* Mode 6, Pull-Down, RxActive */ + P8_45_pwm_pin: pinmux_P8_45_pwm_pin { + pinctrl-single,pins = <0x0a0 0x03>; }; /* Mode 3, Pull-Down*/ + P8_45_hdmi_pin: pinmux_P8_45_hdmi_pin { + pinctrl-single,pins = <0x0a0 0x08>; }; /* lcd_data0.lcd_data0, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ + + /* P8_46 (ZCZ ball R2 ) hdmi */ + P8_46_default_pin: pinmux_P8_46_default_pin { + pinctrl-single,pins = <0x0a4 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_46_gpio_pin: pinmux_P8_46_gpio_pin { + pinctrl-single,pins = <0x0a4 0x2F>; }; /* Mode 7, RxActive */ + P8_46_gpio_pu_pin: pinmux_P8_46_gpio_pu_pin { + pinctrl-single,pins = <0x0a4 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_46_gpio_pd_pin: pinmux_P8_46_gpio_pd_pin { + pinctrl-single,pins = <0x0a4 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_46_pruout_pin: pinmux_P8_46_pruout_pin { + pinctrl-single,pins = <0x0a4 0x05>; }; /* Mode 5, Pull-Down*/ + P8_46_pruin_pin: pinmux_P8_46_pruin_pin { + pinctrl-single,pins = <0x0a4 0x26>; }; /* Mode 6, Pull-Down, RxActive */ + P8_46_pwm_pin: pinmux_P8_46_pwm_pin { + pinctrl-single,pins = <0x0a4 0x03>; }; /* Mode 3, Pull-Down*/ + P8_46_hdmi_pin: pinmux_P8_46_hdmi_pin { + pinctrl-single,pins = <0x0a4 0x08>; }; /* lcd_data1.lcd_data1, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ + + /************************/ + /* P9 Header */ + /************************/ + + /* P9_01 GND */ + /* P9_02 GND */ + /* P9_03 3.3V */ + /* P9_04 3.3V */ + /* P9_05 VDD_5V */ + /* P9_06 VDD_5V */ + /* P9_07 SYS_5V */ + /* P9_08 SYS_5V */ + /* P9_09 PWR_BUT */ + /* P9_10 (ZCZ ball A10) RESETn */ + + /* P9_11 (ZCZ ball T17) */ + P9_11_default_pin: pinmux_P9_11_default_pin { + pinctrl-single,pins = <0x070 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_11_gpio_pin: pinmux_P9_11_gpio_pin { + pinctrl-single,pins = <0x070 0x2F>; }; /* Mode 7, RxActive */ + P9_11_gpio_pu_pin: pinmux_P9_11_gpio_pu_pin { + pinctrl-single,pins = <0x070 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_11_gpio_pd_pin: pinmux_P9_11_gpio_pd_pin { + pinctrl-single,pins = <0x070 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_11_uart_pin: pinmux_P9_11_uart_pin { + pinctrl-single,pins = <0x070 0x36>; }; /* Mode 6, Pull-Up, RxActive */ + + /* P9_12 (ZCZ ball U18) */ + P9_12_default_pin: pinmux_P9_12_default_pin { + pinctrl-single,pins = <0x078 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_12_gpio_pin: pinmux_P9_12_gpio_pin { + pinctrl-single,pins = <0x078 0x2F>; }; /* Mode 7, RxActive */ + P9_12_gpio_pu_pin: pinmux_P9_12_gpio_pu_pin { + pinctrl-single,pins = <0x078 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_12_gpio_pd_pin: pinmux_P9_12_gpio_pd_pin { + pinctrl-single,pins = <0x078 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + + /* P9_13 (ZCZ ball U17) */ + P9_13_default_pin: pinmux_P9_13_default_pin { + pinctrl-single,pins = <0x074 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_13_gpio_pin: pinmux_P9_13_gpio_pin { + pinctrl-single,pins = <0x074 0x2F>; }; /* Mode 7, RxActive */ + P9_13_gpio_pu_pin: pinmux_P9_13_gpio_pu_pin { + pinctrl-single,pins = <0x074 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_13_gpio_pd_pin: pinmux_P9_13_gpio_pd_pin { + pinctrl-single,pins = <0x074 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_13_uart_pin: pinmux_P9_13_uart_pin { + pinctrl-single,pins = <0x074 0x36>; }; /* Mode 6, Pull-Up, RxActive */ + + /* P9_14 (ZCZ ball U14) */ + P9_14_default_pin: pinmux_P9_14_default_pin { + pinctrl-single,pins = <0x048 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_14_gpio_pin: pinmux_P9_14_gpio_pin { + pinctrl-single,pins = <0x048 0x2F>; }; /* Mode 7, RxActive */ + P9_14_gpio_pu_pin: pinmux_P9_14_gpio_pu_pin { + pinctrl-single,pins = <0x048 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_14_gpio_pd_pin: pinmux_P9_14_gpio_pd_pin { + pinctrl-single,pins = <0x048 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_14_pwm_pin: pinmux_P9_14_pwm_pin { + pinctrl-single,pins = <0x048 0x26>; }; /* Mode 6, Pull-Down, RxActive */ + + /* P9_15 (ZCZ ball R13) */ + P9_15_default_pin: pinmux_P9_15_default_pin { + pinctrl-single,pins = <0x040 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_15_gpio_pin: pinmux_P9_15_gpio_pin { + pinctrl-single,pins = <0x040 0x2F>; }; /* Mode 7, RxActive */ + P9_15_gpio_pu_pin: pinmux_P9_15_gpio_pu_pin { + pinctrl-single,pins = <0x040 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_15_gpio_pd_pin: pinmux_P9_15_gpio_pd_pin { + pinctrl-single,pins = <0x040 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_15_pwm_pin: pinmux_P9_15_pwm_pin { + pinctrl-single,pins = <0x040 0x26>; }; /* Mode 6, Pull-Down, RxActive */ + + /* P9_16 (ZCZ ball T14) */ + P9_16_default_pin: pinmux_P9_16_default_pin { + pinctrl-single,pins = <0x04c 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_16_gpio_pin: pinmux_P9_16_gpio_pin { + pinctrl-single,pins = <0x04c 0x2F>; }; /* Mode 7, RxActive */ + P9_16_gpio_pu_pin: pinmux_P9_16_gpio_pu_pin { + pinctrl-single,pins = <0x04c 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_16_gpio_pd_pin: pinmux_P9_16_gpio_pd_pin { + pinctrl-single,pins = <0x04c 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_16_pwm_pin: pinmux_P9_16_pwm_pin { + pinctrl-single,pins = <0x04c 0x26>; }; /* Mode 6, Pull-Down, RxActive */ + + /* P9_17 (ZCZ ball A16) */ + P9_17_default_pin: pinmux_P9_17_default_pin { + pinctrl-single,pins = <0x15c 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_17_gpio_pin: pinmux_P9_17_gpio_pin { + pinctrl-single,pins = <0x15c 0x2F>; }; /* Mode 7, RxActive */ + P9_17_gpio_pu_pin: pinmux_P9_17_gpio_pu_pin { + pinctrl-single,pins = <0x15c 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_17_gpio_pd_pin: pinmux_P9_17_gpio_pd_pin { + pinctrl-single,pins = <0x15c 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_17_spi_pin: pinmux_P9_17_spi_pin { + pinctrl-single,pins = <0x15c 0x30>; }; /* Mode 0, Pull-Up, RxActive */ + P9_17_i2c_pin: pinmux_P9_17_i2c_pin { + pinctrl-single,pins = <0x15c 0x32>; }; /* Mode 2, Pull-Up, RxActive */ + P9_17_pwm_pin: pinmux_P9_17_pwm_pin { + pinctrl-single,pins = <0x15c 0x33>; }; /* Mode 3, Pull-Up, RxActive */ + + /* P9_18 (ZCZ ball B16) */ + P9_18_default_pin: pinmux_P9_18_default_pin { + pinctrl-single,pins = <0x158 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_18_gpio_pin: pinmux_P9_18_gpio_pin { + pinctrl-single,pins = <0x158 0x2F>; }; /* Mode 7, RxActive */ + P9_18_gpio_pu_pin: pinmux_P9_18_gpio_pu_pin { + pinctrl-single,pins = <0x158 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_18_gpio_pd_pin: pinmux_P9_18_gpio_pd_pin { + pinctrl-single,pins = <0x158 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_18_spi_pin: pinmux_P9_18_spi_pin { + pinctrl-single,pins = <0x158 0x30>; }; /* Mode 0, Pull-Up, RxActive */ + P9_18_i2c_pin: pinmux_P9_18_i2c_pin { + pinctrl-single,pins = <0x158 0x32>; }; /* Mode 2, Pull-Up, RxActive */ + P9_18_pwm_pin: pinmux_P9_18_pwm_pin { + pinctrl-single,pins = <0x158 0x33>; }; /* Mode 3, Pull-Up, RxActive */ + + /* P9_19 (ZCZ ball D17) */ + P9_19_default_pin: pinmux_P9_19_default_pin { + pinctrl-single,pins = <0x17c 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_19_gpio_pin: pinmux_P9_19_gpio_pin { + pinctrl-single,pins = <0x17c 0x2F>; }; /* Mode 7, RxActive */ + P9_19_gpio_pu_pin: pinmux_P9_19_gpio_pu_pin { + pinctrl-single,pins = <0x17c 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_19_gpio_pd_pin: pinmux_P9_19_gpio_pd_pin { + pinctrl-single,pins = <0x17c 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_19_can_pin: pinmux_P9_19_can_pin { + pinctrl-single,pins = <0x17c 0x32>; }; /* Mode 2, Pull-Up, RxActive */ + P9_19_i2c_pin: pinmux_P9_19_i2c_pin { + pinctrl-single,pins = <0x17c 0x73>; }; /* (SLEWCTRL_SLOW | PIN_INPUT_PULLUP | MUX_MODE3) */ + + /* P9_20 (ZCZ ball D18) */ + P9_20_default_pin: pinmux_P9_20_default_pin { + pinctrl-single,pins = <0x178 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_20_gpio_pin: pinmux_P9_20_gpio_pin { + pinctrl-single,pins = <0x178 0x2F>; }; /* Mode 7, RxActive */ + P9_20_gpio_pu_pin: pinmux_P9_20_gpio_pu_pin { + pinctrl-single,pins = <0x178 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_20_gpio_pd_pin: pinmux_P9_20_gpio_pd_pin { + pinctrl-single,pins = <0x178 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_20_can_pin: pinmux_P9_20_can_pin { + pinctrl-single,pins = <0x178 0x12>; }; /* Mode 2, Pull-Up, RxActive */ + P9_20_i2c_pin: pinmux_P9_20_i2c_pin { + pinctrl-single,pins = <0x178 0x73>; }; /* (SLEWCTRL_SLOW | PIN_INPUT_PULLUP | MUX_MODE3) */ + + /* P9_21 (ZCZ ball B17) */ + P9_21_default_pin: pinmux_P9_21_default_pin { + pinctrl-single,pins = <0x154 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_21_gpio_pin: pinmux_P9_21_gpio_pin { + pinctrl-single,pins = <0x154 0x2F>; }; /* Mode 7, RxActive */ + P9_21_gpio_pu_pin: pinmux_P9_21_gpio_pu_pin { + pinctrl-single,pins = <0x154 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_21_gpio_pd_pin: pinmux_P9_21_gpio_pd_pin { + pinctrl-single,pins = <0x154 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_21_spi_pin: pinmux_P9_21_spi_pin { + pinctrl-single,pins = <0x154 0x30>; }; /* Mode 0, Pull-Up, RxActive */ + P9_21_uart_pin: pinmux_P9_21_uart_pin { + pinctrl-single,pins = <0x154 0x31>; }; /* Mode 1, Pull-Up, RxActive */ + P9_21_i2c_pin: pinmux_P9_21_i2c_pin { + pinctrl-single,pins = <0x154 0x32>; }; /* Mode 2, Pull-Up, RxActive */ + P9_21_pwm_pin: pinmux_P9_21_pwm_pin { + pinctrl-single,pins = <0x154 0x33>; }; /* Mode 3, Pull-Up, RxActive */ + + /* P9_22 (ZCZ ball A17) */ + P9_22_default_pin: pinmux_P9_22_default_pin { + pinctrl-single,pins = <0x150 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_22_gpio_pin: pinmux_P9_22_gpio_pin { + pinctrl-single,pins = <0x150 0x2F>; }; /* Mode 7, RxActive */ + P9_22_gpio_pu_pin: pinmux_P9_22_gpio_pu_pin { + pinctrl-single,pins = <0x150 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_22_gpio_pd_pin: pinmux_P9_22_gpio_pd_pin { + pinctrl-single,pins = <0x150 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_22_spi_pin: pinmux_P9_22_spi_pin { + pinctrl-single,pins = <0x150 0x30>; }; /* Mode 0, Pull-Up, RxActive */ + P9_22_uart_pin: pinmux_P9_22_uart_pin { + pinctrl-single,pins = <0x150 0x31>; }; /* Mode 1, Pull-Up, RxActive */ + P9_22_i2c_pin: pinmux_P9_22_i2c_pin { + pinctrl-single,pins = <0x150 0x32>; }; /* Mode 2, Pull-Up, RxActive */ + P9_22_pwm_pin: pinmux_P9_22_pwm_pin { + pinctrl-single,pins = <0x150 0x33>; }; /* Mode 3, Pull-Up, RxActive */ + + /* P9_23 (ZCZ ball V14) */ + P9_23_default_pin: pinmux_P9_23_default_pin { + pinctrl-single,pins = <0x044 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_23_gpio_pin: pinmux_P9_23_gpio_pin { + pinctrl-single,pins = <0x044 0x2F>; }; /* Mode 7, RxActive */ + P9_23_gpio_pu_pin: pinmux_P9_23_gpio_pu_pin { + pinctrl-single,pins = <0x044 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_23_gpio_pd_pin: pinmux_P9_23_gpio_pd_pin { + pinctrl-single,pins = <0x044 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_23_pwm_pin: pinmux_P9_23_pwm_pin { + pinctrl-single,pins = <0x044 0x26>; }; /* Mode 6, Pull-Down, RxActive */ + + /* P9_24 (ZCZ ball D15) */ + P9_24_default_pin: pinmux_P9_24_default_pin { + pinctrl-single,pins = <0x184 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_24_gpio_pin: pinmux_P9_24_gpio_pin { + pinctrl-single,pins = <0x184 0x2F>; }; /* Mode 7, RxActive */ + P9_24_gpio_pu_pin: pinmux_P9_24_gpio_pu_pin { + pinctrl-single,pins = <0x184 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_24_gpio_pd_pin: pinmux_P9_24_gpio_pd_pin { + pinctrl-single,pins = <0x184 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_24_uart_pin: pinmux_P9_24_uart_pin { + pinctrl-single,pins = <0x184 0x30>; }; /* Mode 0, Pull-Up, RxActive */ + P9_24_can_pin: pinmux_P9_24_can_pin { + pinctrl-single,pins = <0x184 0x32>; }; /* Mode 2, Pull-Up, RxActive */ + P9_24_i2c_pin: pinmux_P9_24_i2c_pin { + pinctrl-single,pins = <0x184 0x33>; }; /* Mode 3, Pull-Up, RxActive */ + P9_24_pruin_pin: pinmux_P9_24_pruin_pin { + pinctrl-single,pins = <0x184 0x36>; }; /* Mode 6, Pull-Up, RxActive */ + + /* P9_25 (ZCZ ball A14) Audio */ + P9_25_default_pin: pinmux_P9_25_default_pin { + pinctrl-single,pins = <0x1ac 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_25_gpio_pin: pinmux_P9_25_gpio_pin { + pinctrl-single,pins = <0x1ac 0x2F>; }; /* Mode 7, RxActive */ + P9_25_gpio_pu_pin: pinmux_P9_25_gpio_pu_pin { + pinctrl-single,pins = <0x1ac 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_25_gpio_pd_pin: pinmux_P9_25_gpio_pd_pin { + pinctrl-single,pins = <0x1ac 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_25_qep_pin: pinmux_P9_25_qep_pin { + pinctrl-single,pins = <0x1ac 0x21>; }; /* Mode 1, Pull-Down, RxActive */ + P9_25_pruout_pin: pinmux_P9_25_pruout_pin { + pinctrl-single,pins = <0x1ac 0x25>; }; /* Mode 5, Pull-Down, RxActive */ + P9_25_pruin_pin: pinmux_P9_25_pruin_pin { + pinctrl-single,pins = <0x1ac 0x26>; }; /* Mode 6, Pull-Down, RxActive */ + P9_25_audio_pin: pinmux_P9_25_audio_pin { + pinctrl-single,pins = <0x1ac (PIN_INPUT_PULLUP | MUX_MODE0)>; }; /* mcasp0_ahclkx.mcasp0_ahclkx */ + + /* P9_26 (ZCZ ball D16) */ + P9_26_default_pin: pinmux_P9_26_default_pin { + pinctrl-single,pins = <0x180 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_26_gpio_pin: pinmux_P9_26_gpio_pin { + pinctrl-single,pins = <0x180 0x2F>; }; /* Mode 7, RxActive */ + P9_26_gpio_pu_pin: pinmux_P9_26_gpio_pu_pin { + pinctrl-single,pins = <0x180 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_26_gpio_pd_pin: pinmux_P9_26_gpio_pd_pin { + pinctrl-single,pins = <0x180 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_26_uart_pin: pinmux_P9_26_uart_pin { + pinctrl-single,pins = <0x180 0x30>; }; /* Mode 0, Pull-Up, RxActive */ + P9_26_can_pin: pinmux_P9_26_can_pin { + pinctrl-single,pins = <0x180 0x12>; }; /* Mode 2, Pull-Up, RxActive */ + P9_26_i2c_pin: pinmux_P9_26_i2c_pin { + pinctrl-single,pins = <0x180 0x33>; }; /* Mode 3, Pull-Up, RxActive */ + P9_26_pruin_pin: pinmux_P9_26_pruin_pin { + pinctrl-single,pins = <0x180 0x36>; }; /* Mode 6, Pull-Up, RxActive */ + + /* P9_27 (ZCZ ball C13) */ + P9_27_default_pin: pinmux_P9_27_default_pin { + pinctrl-single,pins = <0x1a4 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_27_gpio_pin: pinmux_P9_27_gpio_pin { + pinctrl-single,pins = <0x1a4 0x2F>; }; /* Mode 7, RxActive */ + P9_27_gpio_pu_pin: pinmux_P9_27_gpio_pu_pin { + pinctrl-single,pins = <0x1a4 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_27_gpio_pd_pin: pinmux_P9_27_gpio_pd_pin { + pinctrl-single,pins = <0x1a4 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_27_qep_pin: pinmux_P9_27_qep_pin { + pinctrl-single,pins = <0x1a4 0x21>; }; /* Mode 1, Pull-Down, RxActive */ + P9_27_pruout_pin: pinmux_P9_27_pruout_pin { + pinctrl-single,pins = <0x1a4 0x25>; }; /* Mode 5, Pull-Down, RxActive */ + P9_27_pruin_pin: pinmux_P9_27_pruin_pin { + pinctrl-single,pins = <0x1a4 0x26>; }; /* Mode 6, Pull-Down, RxActive */ + + /* P9_28 (ZCZ ball C12) Audio */ + P9_28_default_pin: pinmux_P9_28_default_pin { + pinctrl-single,pins = <0x19c 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_28_gpio_pin: pinmux_P9_28_gpio_pin { + pinctrl-single,pins = <0x19c 0x2F>; }; /* Mode 7, RxActive */ + P9_28_gpio_pu_pin: pinmux_P9_28_gpio_pu_pin { + pinctrl-single,pins = <0x19c 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_28_gpio_pd_pin: pinmux_P9_28_gpio_pd_pin { + pinctrl-single,pins = <0x19c 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_28_pwm_pin: pinmux_P9_28_pwm_pin { + pinctrl-single,pins = <0x19c 0x21>; }; /* Mode 1, Pull-Down, RxActive */ + P9_28_spi_pin: pinmux_P9_28_spi_pin { + pinctrl-single,pins = <0x19c 0x23>; }; /* Mode 3, Pull-Down, RxActive */ + P9_28_pwm2_pin: pinmux_P9_28_pwm2_pin { + pinctrl-single,pins = <0x19c 0x24>; }; /* Mode 4, Pull-Down, RxActive */ + P9_28_pruout_pin: pinmux_P9_28_pruout_pin { + pinctrl-single,pins = <0x19c 0x25>; }; /* Mode 5, Pull-Down, RxActive */ + P9_28_pruin_pin: pinmux_P9_28_pruin_pin { + pinctrl-single,pins = <0x19c 0x26>; }; /* Mode 6, Pull-Down, RxActive */ + P9_28_audio_pin: pinmux_P9_28_audio_pin { + pinctrl-single,pins = <0x19c (PIN_OUTPUT_PULLDOWN | MUX_MODE2)>; }; /* mcasp0_ahclkr.mcasp0_axr2 */ + + /* P9_29 (ZCZ ball B13) Audio */ + P9_29_default_pin: pinmux_P9_29_default_pin { + pinctrl-single,pins = <0x194 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_29_gpio_pin: pinmux_P9_29_gpio_pin { + pinctrl-single,pins = <0x194 0x2F>; }; /* Mode 7, RxActive */ + P9_29_gpio_pu_pin: pinmux_P9_29_gpio_pu_pin { + pinctrl-single,pins = <0x194 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_29_gpio_pd_pin: pinmux_P9_29_gpio_pd_pin { + pinctrl-single,pins = <0x194 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_29_pwm_pin: pinmux_P9_29_pwm_pin { + pinctrl-single,pins = <0x194 0x21>; }; /* Mode 1, Pull-Down, RxActive */ + P9_29_spi_pin: pinmux_P9_29_spi_pin { + pinctrl-single,pins = <0x194 0x23>; }; /* Mode 3, Pull-Down, RxActive */ + P9_29_pruout_pin: pinmux_P9_29_pruout_pin { + pinctrl-single,pins = <0x194 0x25>; }; /* Mode 5, Pull-Down, RxActive */ + P9_29_pruin_pin: pinmux_P9_29_pruin_pin { + pinctrl-single,pins = <0x194 0x26>; }; /* Mode 6, Pull-Down, RxActive */ + P9_29_audio_pin: pinmux_P9_29_audio_pin { + pinctrl-single,pins = <0x194 (PIN_OUTPUT_PULLUP | MUX_MODE0)>; }; /* mcasp0_fsx.mcasp0_fsx */ + + /* P9_30 (ZCZ ball D12) */ + P9_30_default_pin: pinmux_P9_30_default_pin { + pinctrl-single,pins = <0x198 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_30_gpio_pin: pinmux_P9_30_gpio_pin { + pinctrl-single,pins = <0x198 0x2F>; }; /* Mode 7, RxActive */ + P9_30_gpio_pu_pin: pinmux_P9_30_gpio_pu_pin { + pinctrl-single,pins = <0x198 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_30_gpio_pd_pin: pinmux_P9_30_gpio_pd_pin { + pinctrl-single,pins = <0x198 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_30_pwm_pin: pinmux_P9_30_pwm_pin { + pinctrl-single,pins = <0x198 0x21>; }; /* Mode 1, Pull-Down, RxActive */ + P9_30_spi_pin: pinmux_P9_30_spi_pin { + pinctrl-single,pins = <0x198 0x23>; }; /* Mode 3, Pull-Down, RxActive */ + P9_30_pruout_pin: pinmux_P9_30_pruout_pin { + pinctrl-single,pins = <0x198 0x25>; }; /* Mode 5, Pull-Down, RxActive */ + P9_30_pruin_pin: pinmux_P9_30_pruin_pin { + pinctrl-single,pins = <0x198 0x26>; }; /* Mode 6, Pull-Down, RxActive */ + + /* P9_31 (ZCZ ball A13) Audio */ + P9_31_default_pin: pinmux_P9_31_default_pin { + pinctrl-single,pins = <0x190 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_31_gpio_pin: pinmux_P9_31_gpio_pin { + pinctrl-single,pins = <0x190 0x2F>; }; /* Mode 7, RxActive */ + P9_31_gpio_pu_pin: pinmux_P9_31_gpio_pu_pin { + pinctrl-single,pins = <0x190 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_31_gpio_pd_pin: pinmux_P9_31_gpio_pd_pin { + pinctrl-single,pins = <0x190 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_31_pwm_pin: pinmux_P9_31_pwm_pin { + pinctrl-single,pins = <0x190 0x21>; }; /* Mode 1, Pull-Down, RxActive */ + P9_31_spi_pin: pinmux_P9_31_spi_pin { + pinctrl-single,pins = <0x190 0x23>; }; /* Mode 3, Pull-Down, RxActive */ + P9_31_pruout_pin: pinmux_P9_31_pruout_pin { + pinctrl-single,pins = <0x190 0x25>; }; /* Mode 5, Pull-Down, RxActive */ + P9_31_pruin_pin: pinmux_P9_31_pruin_pin { + pinctrl-single,pins = <0x190 0x26>; }; /* Mode 6, Pull-Down, RxActive */ + P9_31_audio_pin: pinmux_P9_31_audio_pin { + pinctrl-single,pins = <0x190 (PIN_OUTPUT_PULLDOWN | MUX_MODE0)>; }; /* mcasp0_aclkx.mcasp0_aclkx */ + + /* P9_32 VADC */ + /* P9_33 (ZCZ ball C8 ) AIN4 */ + /* P9_34 AGND */ + /* P9_35 (ZCZ ball A8 ) AIN6 */ + /* P9_36 (ZCZ ball B8 ) AIN5 */ + /* P9_37 (ZCZ ball B7 ) AIN2 */ + /* P9_38 (ZCZ ball A7 ) AIN3 */ + /* P9_39 (ZCZ ball B6 ) AIN0 */ + /* P9_40 (ZCZ ball C7 ) AIN1 */ + + /* P9_41 (ZCZ ball D14) */ + P9_41_default_pin: pinmux_P9_41_default_pin { + pinctrl-single,pins = <0x1b4 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_41_gpio_pin: pinmux_P9_41_gpio_pin { + pinctrl-single,pins = <0x1b4 0x2F>; }; /* Mode 7, RxActive */ + P9_41_gpio_pu_pin: pinmux_P9_41_gpio_pu_pin { + pinctrl-single,pins = <0x1b4 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_41_gpio_pd_pin: pinmux_P9_41_gpio_pd_pin { + pinctrl-single,pins = <0x1b4 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_41_timer_pin: pinmux_P9_41_timer_pin { + pinctrl-single,pins = <0x1b4 0x24>; }; /* Mode 4, Pull-Down, RxActive */ + P9_41_pruin_pin: pinmux_P9_41_pruin_pin { + pinctrl-single,pins = <0x1b4 0x25>; }; /* Mode 5, Pull-Down, RxActive */ + + /* P9_41.1 */ + /* P9_91 (ZCZ ball D13) */ + P9_91_default_pin: pinmux_P9_91_default_pin { + pinctrl-single,pins = <0x1a8 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_91_gpio_pin: pinmux_P9_91_gpio_pin { + pinctrl-single,pins = <0x1a8 0x2F>; }; /* Mode 7, RxActive */ + P9_91_gpio_pu_pin: pinmux_P9_91_gpio_pu_pin { + pinctrl-single,pins = <0x1a8 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_91_gpio_pd_pin: pinmux_P9_91_gpio_pd_pin { + pinctrl-single,pins = <0x1a8 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_91_qep_pin: pinmux_P9_91_qep_pin { + pinctrl-single,pins = <0x1a8 0x21>; }; /* Mode 1, Pull-Down, RxActive */ + P9_91_pruout_pin: pinmux_P9_91_pruout_pin { + pinctrl-single,pins = <0x1a8 0x25>; }; /* Mode 5, Pull-Down, RxActive */ + P9_91_pruin_pin: pinmux_P9_91_pruin_pin { + pinctrl-single,pins = <0x1a8 0x26>; }; /* Mode 6, Pull-Down, RxActive */ + + /* P9_42 (ZCZ ball C18) */ + P9_42_default_pin: pinmux_P9_42_default_pin { + pinctrl-single,pins = <0x164 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_42_gpio_pin: pinmux_P9_42_gpio_pin { + pinctrl-single,pins = <0x164 0x2F>; }; /* Mode 7, RxActive */ + P9_42_gpio_pu_pin: pinmux_P9_42_gpio_pu_pin { + pinctrl-single,pins = <0x164 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_42_gpio_pd_pin: pinmux_P9_42_gpio_pd_pin { + pinctrl-single,pins = <0x164 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_42_pwm_pin: pinmux_P9_42_pwm_pin { + pinctrl-single,pins = <0x164 0x20>; }; /* Mode 0, Pull-Down, RxActive */ + P9_42_uart_pin: pinmux_P9_42_uart_pin { + pinctrl-single,pins = <0x164 0x21>; }; /* Mode 1, Pull-Down, RxActive */ + P9_42_spics_pin: pinmux_P9_42_spics_pin { + pinctrl-single,pins = <0x164 0x22>; }; /* Mode 2, Pull-Down, RxActive */ + P9_42_spiclk_pin: pinmux_P9_42_spiclk_pin { + pinctrl-single,pins = <0x164 0x24>; }; /* Mode 4, Pull-Down, RxActive */ + + /* P9_42.1 */ + /* P9_92 (ZCZ ball B12) */ + P9_92_default_pin: pinmux_P9_92_default_pin { + pinctrl-single,pins = <0x1a0 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_92_gpio_pin: pinmux_P9_92_gpio_pin { + pinctrl-single,pins = <0x1a0 0x2F>; }; /* Mode 7, RxActive */ + P9_92_gpio_pu_pin: pinmux_P9_92_gpio_pu_pin { + pinctrl-single,pins = <0x1a0 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_92_gpio_pd_pin: pinmux_P9_92_gpio_pd_pin { + pinctrl-single,pins = <0x1a0 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_92_qep_pin: pinmux_P9_92_qep_pin { + pinctrl-single,pins = <0x1a0 0x21>; }; /* Mode 1, Pull-Down, RxActive */ + P9_92_pruout_pin: pinmux_P9_92_pruout_pin { + pinctrl-single,pins = <0x1a0 0x25>; }; /* Mode 5, Pull-Down, RxActive */ + P9_92_pruin_pin: pinmux_P9_92_pruin_pin { + pinctrl-single,pins = <0x1a0 0x26>; }; /* Mode 6, Pull-Down, RxActive */ + + /* P9_43 GND */ + /* P9_44 GND */ + /* P9_45 GND */ + /* P9_46 GND */ +}; + +/**********************************************************************/ +/* Pin Multiplex Helpers */ +/* */ +/* These provide userspace runtime pin configuration for the */ +/* BeagleBone cape expansion headers */ +/**********************************************************************/ + +&ocp { + /************************/ + /* P8 Header */ + /************************/ + + P8_07_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "timer"; + pinctrl-0 = <&P8_07_default_pin>; + pinctrl-1 = <&P8_07_gpio_pin>; + pinctrl-2 = <&P8_07_gpio_pu_pin>; + pinctrl-3 = <&P8_07_gpio_pd_pin>; + pinctrl-4 = <&P8_07_timer_pin>; + }; + + P8_08_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "timer"; + pinctrl-0 = <&P8_08_default_pin>; + pinctrl-1 = <&P8_08_gpio_pin>; + pinctrl-2 = <&P8_08_gpio_pu_pin>; + pinctrl-3 = <&P8_08_gpio_pd_pin>; + pinctrl-4 = <&P8_08_timer_pin>; + }; + + P8_09_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "timer"; + pinctrl-0 = <&P8_09_default_pin>; + pinctrl-1 = <&P8_09_gpio_pin>; + pinctrl-2 = <&P8_09_gpio_pu_pin>; + pinctrl-3 = <&P8_09_gpio_pd_pin>; + pinctrl-4 = <&P8_09_timer_pin>; + }; + + P8_10_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "timer"; + pinctrl-0 = <&P8_10_default_pin>; + pinctrl-1 = <&P8_10_gpio_pin>; + pinctrl-2 = <&P8_10_gpio_pu_pin>; + pinctrl-3 = <&P8_10_gpio_pd_pin>; + pinctrl-4 = <&P8_10_timer_pin>; + }; + + P8_11_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "pruout", "qep"; + pinctrl-0 = <&P8_11_default_pin>; + pinctrl-1 = <&P8_11_gpio_pin>; + pinctrl-2 = <&P8_11_gpio_pu_pin>; + pinctrl-3 = <&P8_11_gpio_pd_pin>; + pinctrl-4 = <&P8_11_pruout_pin>; + pinctrl-5 = <&P8_11_qep_pin>; + }; + + P8_12_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "pruout", "qep"; + pinctrl-0 = <&P8_12_default_pin>; + pinctrl-1 = <&P8_12_gpio_pin>; + pinctrl-2 = <&P8_12_gpio_pu_pin>; + pinctrl-3 = <&P8_12_gpio_pd_pin>; + pinctrl-4 = <&P8_12_pruout_pin>; + pinctrl-5 = <&P8_12_qep_pin>; + }; + + P8_13_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "pwm"; + pinctrl-0 = <&P8_13_default_pin>; + pinctrl-1 = <&P8_13_gpio_pin>; + pinctrl-2 = <&P8_13_gpio_pu_pin>; + pinctrl-3 = <&P8_13_gpio_pd_pin>; + pinctrl-4 = <&P8_13_pwm_pin>; + }; + + P8_14_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "pwm"; + pinctrl-0 = <&P8_14_default_pin>; + pinctrl-1 = <&P8_14_gpio_pin>; + pinctrl-2 = <&P8_14_gpio_pu_pin>; + pinctrl-3 = <&P8_14_gpio_pd_pin>; + pinctrl-4 = <&P8_14_pwm_pin>; + }; + + P8_15_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "pruin", "qep"; + pinctrl-0 = <&P8_15_default_pin>; + pinctrl-1 = <&P8_15_gpio_pin>; + pinctrl-2 = <&P8_15_gpio_pu_pin>; + pinctrl-3 = <&P8_15_gpio_pd_pin>; + pinctrl-4 = <&P8_15_pruin_pin>; + pinctrl-5 = <&P8_15_qep_pin>; + }; + + P8_16_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "pruin", "qep"; + pinctrl-0 = <&P8_16_default_pin>; + pinctrl-1 = <&P8_16_gpio_pin>; + pinctrl-2 = <&P8_16_gpio_pu_pin>; + pinctrl-3 = <&P8_16_gpio_pd_pin>; + pinctrl-4 = <&P8_16_pruin_pin>; + pinctrl-5 = <&P8_16_qep_pin>; + }; + + P8_17_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "pwm"; + pinctrl-0 = <&P8_17_default_pin>; + pinctrl-1 = <&P8_17_gpio_pin>; + pinctrl-2 = <&P8_17_gpio_pu_pin>; + pinctrl-3 = <&P8_17_gpio_pd_pin>; + pinctrl-4 = <&P8_17_pwm_pin>; + }; + + P8_18_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio"; + pinctrl-0 = <&P8_18_default_pin>; + pinctrl-1 = <&P8_18_gpio_pin>; + pinctrl-2 = <&P8_18_gpio_pu_pin>; + pinctrl-3 = <&P8_18_gpio_pd_pin>; + }; + + P8_19_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "pwm"; + pinctrl-0 = <&P8_19_default_pin>; + pinctrl-1 = <&P8_19_gpio_pin>; + pinctrl-2 = <&P8_19_gpio_pu_pin>; + pinctrl-3 = <&P8_19_gpio_pd_pin>; + pinctrl-4 = <&P8_19_pwm_pin>; + }; + + P8_26_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio"; + pinctrl-0 = <&P8_26_default_pin>; + pinctrl-1 = <&P8_26_gpio_pin>; + pinctrl-2 = <&P8_26_gpio_pu_pin>; + pinctrl-3 = <&P8_26_gpio_pd_pin>; + }; + + P8_27_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "pruout", "pruin", "hdmi"; + pinctrl-0 = <&P8_27_default_pin>; + pinctrl-1 = <&P8_27_gpio_pin>; + pinctrl-2 = <&P8_27_gpio_pu_pin>; + pinctrl-3 = <&P8_27_gpio_pd_pin>; + pinctrl-4 = <&P8_27_pruout_pin>; + pinctrl-5 = <&P8_27_pruin_pin>; + pinctrl-6 = <&P8_27_hdmi_pin>; + }; + + P8_28_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "pruout", "pruin", "hdmi"; + pinctrl-0 = <&P8_28_default_pin>; + pinctrl-1 = <&P8_28_gpio_pin>; + pinctrl-2 = <&P8_28_gpio_pu_pin>; + pinctrl-3 = <&P8_28_gpio_pd_pin>; + pinctrl-4 = <&P8_28_pruout_pin>; + pinctrl-5 = <&P8_28_pruin_pin>; + pinctrl-6 = <&P8_28_hdmi_pin>; + }; + + P8_29_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "pruout", "pruin", "hdmi"; + pinctrl-0 = <&P8_29_default_pin>; + pinctrl-1 = <&P8_29_gpio_pin>; + pinctrl-2 = <&P8_29_gpio_pu_pin>; + pinctrl-3 = <&P8_29_gpio_pd_pin>; + pinctrl-4 = <&P8_29_pruout_pin>; + pinctrl-5 = <&P8_29_pruin_pin>; + pinctrl-6 = <&P8_29_hdmi_pin>; + }; + + P8_30_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "pruout", "pruin", "hdmi"; + pinctrl-0 = <&P8_30_default_pin>; + pinctrl-1 = <&P8_30_gpio_pin>; + pinctrl-2 = <&P8_30_gpio_pu_pin>; + pinctrl-3 = <&P8_30_gpio_pd_pin>; + pinctrl-4 = <&P8_30_pruout_pin>; + pinctrl-5 = <&P8_30_pruin_pin>; + pinctrl-6 = <&P8_30_hdmi_pin>; + }; + + P8_31_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd","uart", "hdmi"; + pinctrl-0 = <&P8_31_default_pin>; + pinctrl-1 = <&P8_31_gpio_pin>; + pinctrl-2 = <&P8_31_gpio_pu_pin>; + pinctrl-3 = <&P8_31_gpio_pd_pin>; + pinctrl-4 = <&P8_31_uart_pin>; + pinctrl-5 = <&P8_31_hdmi_pin>; + }; + + P8_32_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "hdmi"; + pinctrl-0 = <&P8_32_default_pin>; + pinctrl-1 = <&P8_32_gpio_pin>; + pinctrl-2 = <&P8_32_gpio_pu_pin>; + pinctrl-3 = <&P8_32_gpio_pd_pin>; + pinctrl-4 = <&P8_32_hdmi_pin>; + }; + + P8_33_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "hdmi"; + pinctrl-0 = <&P8_33_default_pin>; + pinctrl-1 = <&P8_33_gpio_pin>; + pinctrl-2 = <&P8_33_gpio_pu_pin>; + pinctrl-3 = <&P8_33_gpio_pd_pin>; + pinctrl-4 = <&P8_33_hdmi_pin>; + }; + + P8_34_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd","pwm", "hdmi"; + pinctrl-0 = <&P8_34_default_pin>; + pinctrl-1 = <&P8_34_gpio_pin>; + pinctrl-2 = <&P8_34_gpio_pu_pin>; + pinctrl-3 = <&P8_34_gpio_pd_pin>; + pinctrl-4 = <&P8_34_pwm_pin>; + pinctrl-5 = <&P8_34_hdmi_pin>; + }; + + P8_35_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "hdmi"; + pinctrl-0 = <&P8_35_default_pin>; + pinctrl-1 = <&P8_35_gpio_pin>; + pinctrl-2 = <&P8_35_gpio_pu_pin>; + pinctrl-3 = <&P8_35_gpio_pd_pin>; + pinctrl-4 = <&P8_35_hdmi_pin>; + }; + + P8_36_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd","pwm", "hdmi"; + pinctrl-0 = <&P8_36_default_pin>; + pinctrl-1 = <&P8_36_gpio_pin>; + pinctrl-2 = <&P8_36_gpio_pu_pin>; + pinctrl-3 = <&P8_36_gpio_pd_pin>; + pinctrl-4 = <&P8_36_pwm_pin>; + pinctrl-5 = <&P8_36_hdmi_pin>; + }; + + P8_37_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd","uart","pwm", "hdmi"; + pinctrl-0 = <&P8_37_default_pin>; + pinctrl-1 = <&P8_37_gpio_pin>; + pinctrl-2 = <&P8_37_gpio_pu_pin>; + pinctrl-3 = <&P8_37_gpio_pd_pin>; + pinctrl-4 = <&P8_37_uart_pin>; + pinctrl-5 = <&P8_37_pwm_pin>; + pinctrl-6 = <&P8_37_hdmi_pin>; + }; + + P8_38_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd","uart","pwm", "hdmi"; + pinctrl-0 = <&P8_38_default_pin>; + pinctrl-1 = <&P8_38_gpio_pin>; + pinctrl-2 = <&P8_38_gpio_pu_pin>; + pinctrl-3 = <&P8_38_gpio_pd_pin>; + pinctrl-4 = <&P8_38_uart_pin>; + pinctrl-5 = <&P8_38_pwm_pin>; + pinctrl-6 = <&P8_38_hdmi_pin>; + }; + + P8_39_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "pruout", "pruin", "hdmi"; + pinctrl-0 = <&P8_39_default_pin>; + pinctrl-1 = <&P8_39_gpio_pin>; + pinctrl-2 = <&P8_39_gpio_pu_pin>; + pinctrl-3 = <&P8_39_gpio_pd_pin>; + pinctrl-4 = <&P8_39_pruout_pin>; + pinctrl-5 = <&P8_39_pruin_pin>; + pinctrl-6 = <&P8_39_hdmi_pin>; + }; + + P8_40_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "pruout", "pruin", "hdmi"; + pinctrl-0 = <&P8_40_default_pin>; + pinctrl-1 = <&P8_40_gpio_pin>; + pinctrl-2 = <&P8_40_gpio_pu_pin>; + pinctrl-3 = <&P8_40_gpio_pd_pin>; + pinctrl-4 = <&P8_40_pruout_pin>; + pinctrl-5 = <&P8_40_pruin_pin>; + pinctrl-6 = <&P8_40_hdmi_pin>; + }; + + P8_41_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "pruout", "pruin", "hdmi"; + pinctrl-0 = <&P8_41_default_pin>; + pinctrl-1 = <&P8_41_gpio_pin>; + pinctrl-2 = <&P8_41_gpio_pu_pin>; + pinctrl-3 = <&P8_41_gpio_pd_pin>; + pinctrl-4 = <&P8_41_pruout_pin>; + pinctrl-5 = <&P8_41_pruin_pin>; + pinctrl-6 = <&P8_41_hdmi_pin>; + }; + + P8_42_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "pruout", "pruin", "hdmi"; + pinctrl-0 = <&P8_42_default_pin>; + pinctrl-1 = <&P8_42_gpio_pin>; + pinctrl-2 = <&P8_42_gpio_pu_pin>; + pinctrl-3 = <&P8_42_gpio_pd_pin>; + pinctrl-4 = <&P8_42_pruout_pin>; + pinctrl-5 = <&P8_42_pruin_pin>; + pinctrl-6 = <&P8_42_hdmi_pin>; + }; + + P8_43_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "pruout", "pruin","pwm", "hdmi"; + pinctrl-0 = <&P8_43_default_pin>; + pinctrl-1 = <&P8_43_gpio_pin>; + pinctrl-2 = <&P8_43_gpio_pu_pin>; + pinctrl-3 = <&P8_43_gpio_pd_pin>; + pinctrl-4 = <&P8_43_pruout_pin>; + pinctrl-5 = <&P8_43_pruin_pin>; + pinctrl-6 = <&P8_43_pwm_pin>; + pinctrl-7 = <&P8_43_hdmi_pin>; + }; + + P8_44_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "pruout", "pruin","pwm", "hdmi"; + pinctrl-0 = <&P8_44_default_pin>; + pinctrl-1 = <&P8_44_gpio_pin>; + pinctrl-2 = <&P8_44_gpio_pu_pin>; + pinctrl-3 = <&P8_44_gpio_pd_pin>; + pinctrl-4 = <&P8_44_pruout_pin>; + pinctrl-5 = <&P8_44_pruin_pin>; + pinctrl-6 = <&P8_44_pwm_pin>; + pinctrl-7 = <&P8_44_hdmi_pin>; + }; + + P8_45_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "pruout", "pruin","pwm", "hdmi"; + pinctrl-0 = <&P8_45_default_pin>; + pinctrl-1 = <&P8_45_gpio_pin>; + pinctrl-2 = <&P8_45_gpio_pu_pin>; + pinctrl-3 = <&P8_45_gpio_pd_pin>; + pinctrl-4 = <&P8_45_pruout_pin>; + pinctrl-5 = <&P8_45_pruin_pin>; + pinctrl-6 = <&P8_45_pwm_pin>; + pinctrl-7 = <&P8_45_hdmi_pin>; + }; + + P8_46_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "pruout", "pruin","pwm", "hdmi"; + pinctrl-0 = <&P8_46_default_pin>; + pinctrl-1 = <&P8_46_gpio_pin>; + pinctrl-2 = <&P8_46_gpio_pu_pin>; + pinctrl-3 = <&P8_46_gpio_pd_pin>; + pinctrl-4 = <&P8_46_pruout_pin>; + pinctrl-5 = <&P8_46_pruin_pin>; + pinctrl-6 = <&P8_46_pwm_pin>; + pinctrl-7 = <&P8_46_hdmi_pin>; + }; + + /************************/ + /* P9 Header */ + /************************/ + + P9_11_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "uart"; + pinctrl-0 = <&P9_11_default_pin>; + pinctrl-1 = <&P9_11_gpio_pin>; + pinctrl-2 = <&P9_11_gpio_pu_pin>; + pinctrl-3 = <&P9_11_gpio_pd_pin>; + pinctrl-4 = <&P9_11_uart_pin>; + }; + + P9_12_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio"; + pinctrl-0 = <&P9_12_default_pin>; + pinctrl-1 = <&P9_12_gpio_pin>; + pinctrl-2 = <&P9_12_gpio_pu_pin>; + pinctrl-3 = <&P9_12_gpio_pd_pin>; + }; + + P9_13_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "uart"; + pinctrl-0 = <&P9_13_default_pin>; + pinctrl-1 = <&P9_13_gpio_pin>; + pinctrl-2 = <&P9_13_gpio_pu_pin>; + pinctrl-3 = <&P9_13_gpio_pd_pin>; + pinctrl-4 = <&P9_13_uart_pin>; + }; + + P9_14_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "pwm"; + pinctrl-0 = <&P9_14_default_pin>; + pinctrl-1 = <&P9_14_gpio_pin>; + pinctrl-2 = <&P9_14_gpio_pu_pin>; + pinctrl-3 = <&P9_14_gpio_pd_pin>; + pinctrl-4 = <&P9_14_pwm_pin>; + }; + + P9_15_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "pwm"; + pinctrl-0 = <&P9_15_default_pin>; + pinctrl-1 = <&P9_15_gpio_pin>; + pinctrl-2 = <&P9_15_gpio_pu_pin>; + pinctrl-3 = <&P9_15_gpio_pd_pin>; + pinctrl-4 = <&P9_15_pwm_pin>; + }; + + P9_16_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "pwm"; + pinctrl-0 = <&P9_16_default_pin>; + pinctrl-1 = <&P9_16_gpio_pin>; + pinctrl-2 = <&P9_16_gpio_pu_pin>; + pinctrl-3 = <&P9_16_gpio_pd_pin>; + pinctrl-4 = <&P9_16_pwm_pin>; + }; + + P9_17_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "spi", "i2c", "pwm"; + pinctrl-0 = <&P9_17_default_pin>; + pinctrl-1 = <&P9_17_gpio_pin>; + pinctrl-2 = <&P9_17_gpio_pu_pin>; + pinctrl-3 = <&P9_17_gpio_pd_pin>; + pinctrl-4 = <&P9_17_spi_pin>; + pinctrl-5 = <&P9_17_i2c_pin>; + pinctrl-6 = <&P9_17_pwm_pin>; + }; + + P9_18_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "spi", "i2c", "pwm"; + pinctrl-0 = <&P9_18_default_pin>; + pinctrl-1 = <&P9_18_gpio_pin>; + pinctrl-2 = <&P9_18_gpio_pu_pin>; + pinctrl-3 = <&P9_18_gpio_pd_pin>; + pinctrl-4 = <&P9_18_spi_pin>; + pinctrl-5 = <&P9_18_i2c_pin>; + pinctrl-6 = <&P9_18_pwm_pin>; + }; + + P9_19_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "can", "i2c"; + pinctrl-0 = <&P9_19_default_pin>; + pinctrl-1 = <&P9_19_gpio_pin>; + pinctrl-2 = <&P9_19_gpio_pu_pin>; + pinctrl-3 = <&P9_19_gpio_pd_pin>; + pinctrl-4 = <&P9_19_can_pin>; + pinctrl-5 = <&P9_19_i2c_pin>; + }; + + P9_20_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "can", "i2c"; + pinctrl-0 = <&P9_20_default_pin>; + pinctrl-1 = <&P9_20_gpio_pin>; + pinctrl-2 = <&P9_20_gpio_pu_pin>; + pinctrl-3 = <&P9_20_gpio_pd_pin>; + pinctrl-4 = <&P9_20_can_pin>; + pinctrl-5 = <&P9_20_i2c_pin>; + }; + + P9_21_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "spi", "uart", "i2c", "pwm"; + pinctrl-0 = <&P9_21_default_pin>; + pinctrl-1 = <&P9_21_gpio_pin>; + pinctrl-2 = <&P9_21_gpio_pu_pin>; + pinctrl-3 = <&P9_21_gpio_pd_pin>; + pinctrl-4 = <&P9_21_spi_pin>; + pinctrl-5 = <&P9_21_uart_pin>; + pinctrl-6 = <&P9_21_i2c_pin>; + pinctrl-7 = <&P9_21_pwm_pin>; + }; + + P9_22_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "spi", "uart", "i2c", "pwm"; + pinctrl-0 = <&P9_22_default_pin>; + pinctrl-1 = <&P9_22_gpio_pin>; + pinctrl-2 = <&P9_22_gpio_pu_pin>; + pinctrl-3 = <&P9_22_gpio_pd_pin>; + pinctrl-4 = <&P9_22_spi_pin>; + pinctrl-5 = <&P9_22_uart_pin>; + pinctrl-6 = <&P9_22_i2c_pin>; + pinctrl-7 = <&P9_22_pwm_pin>; + }; + + P9_23_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "pwm"; + pinctrl-0 = <&P9_23_default_pin>; + pinctrl-1 = <&P9_23_gpio_pin>; + pinctrl-2 = <&P9_23_gpio_pu_pin>; + pinctrl-3 = <&P9_23_gpio_pd_pin>; + pinctrl-4 = <&P9_23_pwm_pin>; + }; + + P9_24_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "uart", "can", "i2c", "pruin"; + pinctrl-0 = <&P9_24_default_pin>; + pinctrl-1 = <&P9_24_gpio_pin>; + pinctrl-2 = <&P9_24_gpio_pu_pin>; + pinctrl-3 = <&P9_24_gpio_pd_pin>; + pinctrl-4 = <&P9_24_uart_pin>; + pinctrl-5 = <&P9_24_can_pin>; + pinctrl-6 = <&P9_24_i2c_pin>; + pinctrl-7 = <&P9_24_pruin_pin>; + }; + + P9_25_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "qep", "pruout", "pruin", "audio"; + pinctrl-0 = <&P9_25_default_pin>; + pinctrl-1 = <&P9_25_gpio_pin>; + pinctrl-2 = <&P9_25_gpio_pu_pin>; + pinctrl-3 = <&P9_25_gpio_pd_pin>; + pinctrl-4 = <&P9_25_qep_pin>; + pinctrl-5 = <&P9_25_pruout_pin>; + pinctrl-6 = <&P9_25_pruin_pin>; + pinctrl-7 = <&P9_25_audio_pin>; + }; + + P9_26_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "uart", "can", "i2c", "pruin"; + pinctrl-0 = <&P9_26_default_pin>; + pinctrl-1 = <&P9_26_gpio_pin>; + pinctrl-2 = <&P9_26_gpio_pu_pin>; + pinctrl-3 = <&P9_26_gpio_pd_pin>; + pinctrl-4 = <&P9_26_uart_pin>; + pinctrl-5 = <&P9_26_can_pin>; + pinctrl-6 = <&P9_26_i2c_pin>; + pinctrl-7 = <&P9_26_pruin_pin>; + }; + + P9_27_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "qep", "pruout", "pruin"; + pinctrl-0 = <&P9_27_default_pin>; + pinctrl-1 = <&P9_27_gpio_pin>; + pinctrl-2 = <&P9_27_gpio_pu_pin>; + pinctrl-3 = <&P9_27_gpio_pd_pin>; + pinctrl-4 = <&P9_27_qep_pin>; + pinctrl-5 = <&P9_27_pruout_pin>; + pinctrl-6 = <&P9_27_pruin_pin>; + }; + + P9_28_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "pwm", "spi", "pwm2", "pruout", "pruin", "audio"; + pinctrl-0 = <&P9_28_default_pin>; + pinctrl-1 = <&P9_28_gpio_pin>; + pinctrl-2 = <&P9_28_gpio_pu_pin>; + pinctrl-3 = <&P9_28_gpio_pd_pin>; + pinctrl-4 = <&P9_28_pwm_pin>; + pinctrl-5 = <&P9_28_spi_pin>; + pinctrl-6 = <&P9_28_pwm2_pin>; + pinctrl-7 = <&P9_28_pruout_pin>; + pinctrl-8 = <&P9_28_pruin_pin>; + pinctrl-9 = <&P9_28_audio_pin>; + }; + + P9_29_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "pwm", "spi", "pruout", "pruin", "audio"; + pinctrl-0 = <&P9_29_default_pin>; + pinctrl-1 = <&P9_29_gpio_pin>; + pinctrl-2 = <&P9_29_gpio_pu_pin>; + pinctrl-3 = <&P9_29_gpio_pd_pin>; + pinctrl-4 = <&P9_29_pwm_pin>; + pinctrl-5 = <&P9_29_spi_pin>; + pinctrl-6 = <&P9_29_pruout_pin>; + pinctrl-7 = <&P9_29_pruin_pin>; + pinctrl-8 = <&P9_29_audio_pin>; + }; + + P9_30_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "pwm", "spi", "pruout", "pruin"; + pinctrl-0 = <&P9_30_default_pin>; + pinctrl-1 = <&P9_30_gpio_pin>; + pinctrl-2 = <&P9_30_gpio_pu_pin>; + pinctrl-3 = <&P9_30_gpio_pd_pin>; + pinctrl-4 = <&P9_30_pwm_pin>; + pinctrl-5 = <&P9_30_spi_pin>; + pinctrl-6 = <&P9_30_pruout_pin>; + pinctrl-7 = <&P9_30_pruin_pin>; + }; + + P9_31_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "pwm", "spi", "pruout", "pruin", "audio"; + pinctrl-0 = <&P9_31_default_pin>; + pinctrl-1 = <&P9_31_gpio_pin>; + pinctrl-2 = <&P9_31_gpio_pu_pin>; + pinctrl-3 = <&P9_31_gpio_pd_pin>; + pinctrl-4 = <&P9_31_pwm_pin>; + pinctrl-5 = <&P9_31_spi_pin>; + pinctrl-6 = <&P9_31_pruout_pin>; + pinctrl-7 = <&P9_31_pruin_pin>; + pinctrl-8 = <&P9_31_audio_pin>; + }; + + P9_41_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "timer", "pruin"; + pinctrl-0 = <&P9_41_default_pin>; + pinctrl-1 = <&P9_41_gpio_pin>; + pinctrl-2 = <&P9_41_gpio_pu_pin>; + pinctrl-3 = <&P9_41_gpio_pd_pin>; + pinctrl-4 = <&P9_41_timer_pin>; + pinctrl-5 = <&P9_41_pruin_pin>; + }; + + P9_91_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "qep", "pruout", "pruin"; + pinctrl-0 = <&P9_91_default_pin>; + pinctrl-1 = <&P9_91_gpio_pin>; + pinctrl-2 = <&P9_91_gpio_pu_pin>; + pinctrl-3 = <&P9_91_gpio_pd_pin>; + pinctrl-4 = <&P9_91_qep_pin>; + pinctrl-5 = <&P9_91_pruout_pin>; + pinctrl-6 = <&P9_91_pruin_pin>; + }; + + P9_42_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "pwm", "uart", "spics", "spiclk"; + pinctrl-0 = <&P9_42_default_pin>; + pinctrl-1 = <&P9_42_gpio_pin>; + pinctrl-2 = <&P9_42_gpio_pu_pin>; + pinctrl-3 = <&P9_42_gpio_pd_pin>; + pinctrl-4 = <&P9_42_pwm_pin>; + pinctrl-5 = <&P9_42_uart_pin>; + pinctrl-6 = <&P9_42_spics_pin>; + pinctrl-7 = <&P9_42_spiclk_pin>; + }; + + P9_92_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "qep", "pruout", "pruin"; + pinctrl-0 = <&P9_92_default_pin>; + pinctrl-1 = <&P9_92_gpio_pin>; + pinctrl-2 = <&P9_92_gpio_pu_pin>; + pinctrl-3 = <&P9_92_gpio_pd_pin>; + pinctrl-4 = <&P9_92_qep_pin>; + pinctrl-5 = <&P9_92_pruout_pin>; + pinctrl-6 = <&P9_92_pruin_pin>; + }; + + cape-universal { + compatible = "gpio-of-helper"; + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <>; + + P8_07 { + gpio-name = "P8_07"; + gpio = <&gpio2 2 0>; + input; + dir-changeable; + }; + P8_08 { + gpio-name = "P8_08"; + gpio = <&gpio2 3 0>; + input; + dir-changeable; + }; + P8_09 { + gpio-name = "P8_09"; + gpio = <&gpio2 5 0>; + input; + dir-changeable; + }; + P8_10 { + gpio-name = "P8_10"; + gpio = <&gpio2 4 0>; + input; + dir-changeable; + }; + P8_11 { + gpio-name = "P8_11"; + gpio = <&gpio1 13 0>; + input; + dir-changeable; + }; + P8_12 { + gpio-name = "P8_12"; + gpio = <&gpio1 12 0>; + input; + dir-changeable; + }; + P8_13 { + gpio-name = "P8_13"; + gpio = <&gpio0 23 0>; + input; + dir-changeable; + }; + P8_14 { + gpio-name = "P8_14"; + gpio = <&gpio0 26 0>; + input; + dir-changeable; + }; + P8_15 { + gpio-name = "P8_15"; + gpio = <&gpio1 15 0>; + input; + dir-changeable; + }; + P8_16 { + gpio-name = "P8_16"; + gpio = <&gpio1 14 0>; + input; + dir-changeable; + }; + P8_17 { + gpio-name = "P8_17"; + gpio = <&gpio0 27 0>; + input; + dir-changeable; + }; + P8_18 { + gpio-name = "P8_18"; + gpio = <&gpio2 1 0>; + input; + dir-changeable; + }; + P8_19 { + gpio-name = "P8_19"; + gpio = <&gpio0 22 0>; + input; + dir-changeable; + }; + + P8_26 { + gpio-name = "P8_26"; + gpio = <&gpio1 29 0>; + input; + dir-changeable; + }; + P8_27 { + gpio-name = "P8_27"; + gpio = <&gpio2 22 0>; + input; + dir-changeable; + }; + P8_28 { + gpio-name = "P8_28"; + gpio = <&gpio2 24 0>; + input; + dir-changeable; + }; + P8_29 { + gpio-name = "P8_29"; + gpio = <&gpio2 23 0>; + input; + dir-changeable; + }; + P8_30 { + gpio-name = "P8_30"; + gpio = <&gpio2 25 0>; + input; + dir-changeable; + }; + P8_31 { + gpio-name = "P8_31"; + gpio = <&gpio0 10 0>; + input; + dir-changeable; + }; + P8_32 { + gpio-name = "P8_32"; + gpio = <&gpio0 11 0>; + input; + dir-changeable; + }; + P8_33 { + gpio-name = "P8_33"; + gpio = <&gpio0 9 0>; + input; + dir-changeable; + }; + P8_34 { + gpio-name = "P8_34"; + gpio = <&gpio2 17 0>; + input; + dir-changeable; + }; + P8_35 { + gpio-name = "P8_35"; + gpio = <&gpio0 8 0>; + input; + dir-changeable; + }; + P8_36 { + gpio-name = "P8_36"; + gpio = <&gpio2 16 0>; + input; + dir-changeable; + }; + P8_37 { + gpio-name = "P8_37"; + gpio = <&gpio2 14 0>; + input; + dir-changeable; + }; + P8_38 { + gpio-name = "P8_38"; + gpio = <&gpio2 15 0>; + input; + dir-changeable; + }; + P8_39 { + gpio-name = "P8_39"; + gpio = <&gpio2 12 0>; + input; + dir-changeable; + }; + P8_40 { + gpio-name = "P8_40"; + gpio = <&gpio2 13 0>; + input; + dir-changeable; + }; + P8_41 { + gpio-name = "P8_41"; + gpio = <&gpio2 10 0>; + input; + dir-changeable; + }; + P8_42 { + gpio-name = "P8_42"; + gpio = <&gpio2 11 0>; + input; + dir-changeable; + }; + P8_43 { + gpio-name = "P8_43"; + gpio = <&gpio2 8 0>; + input; + dir-changeable; + }; + P8_44 { + gpio-name = "P8_44"; + gpio = <&gpio2 9 0>; + input; + dir-changeable; + }; + P8_45 { + gpio-name = "P8_45"; + gpio = <&gpio2 6 0>; + input; + dir-changeable; + }; + P8_46 { + gpio-name = "P8_46"; + gpio = <&gpio2 7 0>; + input; + dir-changeable; + }; + + + P9_11 { + gpio-name = "P9_11"; + gpio = <&gpio0 30 0>; + input; + dir-changeable; + }; + P9_12 { + gpio-name = "P9_12"; + gpio = <&gpio1 28 0>; + input; + dir-changeable; + }; + P9_13 { + gpio-name = "P9_13"; + gpio = <&gpio0 31 0>; + input; + dir-changeable; + }; + P9_14 { + gpio-name = "P9_14"; + gpio = <&gpio1 18 0>; + input; + dir-changeable; + }; + P9_15 { + gpio-name = "P9_15"; + gpio = <&gpio1 16 0>; + input; + dir-changeable; + }; + P9_16 { + gpio-name = "P9_16"; + gpio = <&gpio1 19 0>; + input; + dir-changeable; + }; + P9_17 { + gpio-name = "P9_17"; + gpio = <&gpio0 5 0>; + input; + dir-changeable; + }; + P9_18 { + gpio-name = "P9_18"; + gpio = <&gpio0 4 0>; + input; + dir-changeable; + }; + P9_19 { + gpio-name = "P9_19"; + gpio = <&gpio0 13 0>; + input; + dir-changeable; + }; + P9_20 { + gpio-name = "P9_20"; + gpio = <&gpio0 12 0>; + input; + dir-changeable; + }; + P9_21 { + gpio-name = "P9_21"; + gpio = <&gpio0 3 0>; + input; + dir-changeable; + }; + P9_22 { + gpio-name = "P9_22"; + gpio = <&gpio0 2 0>; + input; + dir-changeable; + }; + P9_23 { + gpio-name = "P9_23"; + gpio = <&gpio1 17 0>; + input; + dir-changeable; + }; + P9_24 { + gpio-name = "P9_24"; + gpio = <&gpio0 15 0>; + input; + dir-changeable; + }; + P9_25 { + gpio-name = "P9_25"; + gpio = <&gpio3 21 0>; + input; + dir-changeable; + }; + P9_26 { + gpio-name = "P9_26"; + gpio = <&gpio0 14 0>; + input; + dir-changeable; + }; + P9_27 { + gpio-name = "P9_27"; + gpio = <&gpio3 19 0>; + input; + dir-changeable; + }; + P9_28 { + gpio-name = "P9_28"; + gpio = <&gpio3 17 0>; + input; + dir-changeable; + }; + P9_29 { + gpio-name = "P9_29"; + gpio = <&gpio3 15 0>; + input; + dir-changeable; + }; + P9_30 { + gpio-name = "P9_30"; + gpio = <&gpio3 16 0>; + input; + dir-changeable; + }; + P9_31 { + gpio-name = "P9_31"; + gpio = <&gpio3 14 0>; + input; + dir-changeable; + }; + P9_41 { + gpio-name = "P9_41"; + gpio = <&gpio0 20 0>; + input; + dir-changeable; + }; + P9_91 { + gpio-name = "P9_91"; + gpio = <&gpio3 20 0>; + input; + dir-changeable; + }; + P9_42 { + gpio-name = "P9_42"; + gpio = <&gpio0 7 0>; + input; + dir-changeable; + }; + P9_92 { + gpio-name = "P9_92"; + gpio = <&gpio3 18 0>; + input; + dir-changeable; + }; + }; +}; diff --git a/arch/arm/boot/dts/am335x-bone-common.dtsi b/arch/arm/boot/dts/am335x-bone-common.dtsi index 007b5e5a5..54a3b8de9 100644 --- a/arch/arm/boot/dts/am335x-bone-common.dtsi +++ b/arch/arm/boot/dts/am335x-bone-common.dtsi @@ -6,6 +6,8 @@ * published by the Free Software Foundation. */ +#include + / { cpus { cpu@0 { @@ -29,14 +31,14 @@ compatible = "gpio-leds"; led2 { - label = "beaglebone:green:heartbeat"; + label = "beaglebone:green:usr0"; gpios = <&gpio1 21 GPIO_ACTIVE_HIGH>; linux,default-trigger = "heartbeat"; default-state = "off"; }; led3 { - label = "beaglebone:green:mmc0"; + label = "beaglebone:green:usr1"; gpios = <&gpio1 22 GPIO_ACTIVE_HIGH>; linux,default-trigger = "mmc0"; default-state = "off"; @@ -66,9 +68,6 @@ }; &am33xx_pinmux { - pinctrl-names = "default"; - pinctrl-0 = <&clkout2_pin>; - user_leds_s0: user_leds_s0 { pinctrl-single,pins = < AM33XX_IOPAD(0x854, PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a5.gpio1_21 */ @@ -99,15 +98,11 @@ >; }; - clkout2_pin: pinmux_clkout2_pin { - pinctrl-single,pins = < - AM33XX_IOPAD(0x9b4, PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* xdma_event_intr1.clkout2 */ - >; - }; - cpsw_default: cpsw_default { pinctrl-single,pins = < /* Slave 1 */ + 0x108 (PIN_INPUT | MUX_MODE0) /* mii1_col.mii1_col */ + 0x10c (PIN_INPUT | MUX_MODE0) /* mii1_crs.mii1_crs */ AM33XX_IOPAD(0x910, PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxerr.mii1_rxerr */ AM33XX_IOPAD(0x914, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mii1_txen.mii1_txen */ AM33XX_IOPAD(0x918, PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxdv.mii1_rxdv */ @@ -127,6 +122,8 @@ cpsw_sleep: cpsw_sleep { pinctrl-single,pins = < /* Slave 1 reset value */ + 0x108 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x10c (PIN_INPUT_PULLDOWN | MUX_MODE7) AM33XX_IOPAD(0x910, PIN_INPUT_PULLDOWN | MUX_MODE7) AM33XX_IOPAD(0x914, PIN_INPUT_PULLDOWN | MUX_MODE7) AM33XX_IOPAD(0x918, PIN_INPUT_PULLDOWN | MUX_MODE7) @@ -310,8 +307,23 @@ * by the hardware problems. (Tip: double-check by performing a current * measurement after shutdown: it should be less than 1 mA.) */ + + interrupts = <7>; /* NMI */ + interrupt-parent = <&intc>; + ti,pmic-shutdown-controller; + charger { + interrupts = , ; + interrupts-names = "AC", "USB"; + status = "okay"; + }; + + pwrbutton { + interrupts = ; + status = "okay"; + }; + regulators { dcdc1_reg: regulator@0 { regulator-name = "vdds_dpr"; @@ -393,3 +405,32 @@ &sham { status = "okay"; }; + +&rtc { + system-power-controller; +}; + +/* the cape manager */ +/ { + bone_capemgr { + compatible = "ti,bone-capemgr"; + status = "okay"; + + nvmem-cells = <&baseboard_data &cape0_data &cape1_data &cape2_data &cape3_data>; + nvmem-cell-names = "baseboard", "slot0", "slot1", "slot2", "slot3"; + #slots = <4>; + + /* map board revisions to compatible definitions */ + baseboardmaps { + baseboard_beaglebone: board@0 { + board-name = "A335BONE"; + compatible-name = "ti,beaglebone"; + }; + + baseboard_beaglebone_black: board@1 { + board-name = "A335BNLT"; + compatible-name = "ti,beaglebone-black"; + }; + }; + }; +}; diff --git b/arch/arm/boot/dts/am335x-bone-emmc-in-reset.dtsi b/arch/arm/boot/dts/am335x-bone-emmc-in-reset.dtsi new file mode 100644 index 000000000..7d8f67322 --- /dev/null +++ b/arch/arm/boot/dts/am335x-bone-emmc-in-reset.dtsi @@ -0,0 +1,18 @@ +/* + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +/* standard */ + +&gpio1 { + emmc_rst { + gpio-hog; + gpios = <20 0>; + output-high; + line-name = "EMMC ResetN"; + }; +}; diff --git b/arch/arm/boot/dts/am335x-bone-jtag.dtsi b/arch/arm/boot/dts/am335x-bone-jtag.dtsi new file mode 100644 index 000000000..603ef0a4d --- /dev/null +++ b/arch/arm/boot/dts/am335x-bone-jtag.dtsi @@ -0,0 +1,20 @@ +/* + * Device Tree Source for bone jtag + * + * Copyright (C) 2015 Robert Nelson + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +&am33xx_pinmux { + pinctrl-names = "default"; + pinctrl-0 = <&clkout2_pin>; + + clkout2_pin: pinmux_clkout2_pin { + pinctrl-single,pins = < + AM33XX_IOPAD(0x9b4, PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* xdma_event_intr1.clkout2 */ + >; + }; +}; diff --git b/arch/arm/boot/dts/am335x-bone-pinmux-can0.dtsi b/arch/arm/boot/dts/am335x-bone-pinmux-can0.dtsi new file mode 100644 index 000000000..09612160b --- /dev/null +++ b/arch/arm/boot/dts/am335x-bone-pinmux-can0.dtsi @@ -0,0 +1,45 @@ +/* + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include +#include "am335x-peripheral-can0.dtsi" + +/* cape universal */ + +/* + *&ocp { + * P9_19_pinmux { + * mode = "can"; + * }; + * P9_20_pinmux { + * mode = "can"; + * }; + *}; + * + *&dcan0 { + * pinctrl-0 = <>; + *}; + * + */ + +/* standard */ + +&am33xx_pinmux { + dcan0_pins: pinmux_dcan0_pins { + pinctrl-single,pins = < + /* P9_20: uart1_ctsn.d_can0_tx */ + BONE_P9_20 (PIN_OUTPUT_PULLUP | MUX_MODE2) + /* P9_19: uart1_rtsn.d_can0_rx */ + BONE_P9_19 (PIN_INPUT_PULLUP | MUX_MODE2) + >; + }; +}; + +&dcan0 { + pinctrl-0 = <&dcan0_pins>; +}; diff --git b/arch/arm/boot/dts/am335x-bone-pinmux-can1.dtsi b/arch/arm/boot/dts/am335x-bone-pinmux-can1.dtsi new file mode 100644 index 000000000..9e264132c --- /dev/null +++ b/arch/arm/boot/dts/am335x-bone-pinmux-can1.dtsi @@ -0,0 +1,45 @@ +/* + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include +#include "am335x-peripheral-can1.dtsi" + +/* cape universal */ + +/* + *&ocp { + * P9_24_pinmux { + * mode = "can"; + * }; + * P9_26_pinmux { + * mode = "can"; + * }; + *}; + * + *&dcan1 { + * pinctrl-0 = <>; + *}; + * + */ + +/* standard */ + +&am33xx_pinmux { + dcan1_pins: pinmux_dcan1_pins { + pinctrl-single,pins = < + /* P9_26: uart1_rxd.d_can1_tx */ + BONE_P9_26 (PIN_OUTPUT_PULLUP | MUX_MODE2) + /* P9_24: uart1_txd.d_can1_rx */ + BONE_P9_24 (PIN_INPUT_PULLUP | MUX_MODE2) + >; + }; +}; + +&dcan1 { + pinctrl-0 = <&dcan1_pins>; +}; diff --git b/arch/arm/boot/dts/am335x-bone-pinmux-emmc.dtsi b/arch/arm/boot/dts/am335x-bone-pinmux-emmc.dtsi new file mode 100644 index 000000000..22cf4621b --- /dev/null +++ b/arch/arm/boot/dts/am335x-bone-pinmux-emmc.dtsi @@ -0,0 +1,88 @@ +/* + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +/* Testing */ +/* lsblk */ + +#include +#include "am335x-peripheral-emmc.dtsi" + +/* cape universal */ + +/* + *&ocp { + * P8_21_pinmux { + * state = "disabled"; + * }; + * P8_20_pinmux { + * state = "disabled"; + * }; + * P8_25_pinmux { + * state = "disabled"; + * }; + * P8_24_pinmux { + * state = "disabled"; + * }; + * P8_05_pinmux { + * state = "disabled"; + * }; + * P8_06_pinmux { + * state = "disabled"; + * }; + * P8_23_pinmux { + * state = "disabled"; + * }; + * P8_22_pinmux { + * state = "disabled"; + * }; + * P8_03_pinmux { + * state = "disabled"; + * }; + * P8_04_pinmux { + * state = "disabled"; + * }; + *}; + * + *&mmc2 { + * pinctrl-0 = <>; + *}; + * + */ + +/* standard */ + +&am33xx_pinmux { + emmc_pins: pinmux_emmc_pins { + pinctrl-single,pins = < + /* P8_21: gpmc_csn1.mmc1_clk */ + BONE_P8_21 (PIN_INPUT_PULLUP | MUX_MODE2) + /* P8_20: gpmc_csn2.mmc1_cmd */ + BONE_P8_20 (PIN_INPUT_PULLUP | MUX_MODE2) + /* P8_25: gpmc_ad0.mmc1_dat0 */ + BONE_P8_25 (PIN_INPUT_PULLUP | MUX_MODE1) + /* P8_24: gpmc_ad1.mmc1_dat1 */ + BONE_P8_24 (PIN_INPUT_PULLUP | MUX_MODE1) + /* P8_05: gpmc_ad2.mmc1_dat2 */ + BONE_P8_05 (PIN_INPUT_PULLUP | MUX_MODE1) + /* P8_06: gpmc_ad3.mmc1_dat3 */ + BONE_P8_06 (PIN_INPUT_PULLUP | MUX_MODE1) + /* P8_23: gpmc_ad4.mmc1_dat4 */ + BONE_P8_23 (PIN_INPUT_PULLUP | MUX_MODE1) + /* P8_22: gpmc_ad5.mmc1_dat5 */ + BONE_P8_22 (PIN_INPUT_PULLUP | MUX_MODE1) + /* P8_03: gpmc_ad6.mmc1_dat6 */ + BONE_P8_03 (PIN_INPUT_PULLUP | MUX_MODE1) + /* P8_04: gpmc_ad7.mmc1_dat7 */ + BONE_P8_04 (PIN_INPUT_PULLUP | MUX_MODE1) + >; + }; +}; + +&mmc2 { + pinctrl-0 = <&emmc_pins>; +}; diff --git b/arch/arm/boot/dts/am335x-bone-pinmux-i2c2.dtsi b/arch/arm/boot/dts/am335x-bone-pinmux-i2c2.dtsi new file mode 100644 index 000000000..abf3b5752 --- /dev/null +++ b/arch/arm/boot/dts/am335x-bone-pinmux-i2c2.dtsi @@ -0,0 +1,45 @@ +/* + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include +#include "am335x-peripheral-i2c2.dtsi" + +/* cape universal */ + +/* + *&ocp { + * P9_19_pinmux { + * mode = "i2c"; + * }; + * P9_20_pinmux { + * mode = "i2c"; + * }; + *}; + * + *&dcan0 { + * pinctrl-0 = <>; + *}; + * + */ + +/* standard */ + +&am33xx_pinmux { + i2c2_pins: pinmux_i2c2_pins { + pinctrl-single,pins = < + /* P9_20: uart1_ctsn.i2c2_sda */ + BONE_P9_20 (SLEWCTRL_SLOW | PIN_INPUT_PULLUP | MUX_MODE3) + /* P9_19: uart1_rtsn.i2c2_scl */ + BONE_P9_19 (SLEWCTRL_SLOW | PIN_INPUT_PULLUP | MUX_MODE3) + >; + }; +}; + +&i2c2 { + pinctrl-0 = <&i2c2_pins>; +}; diff --git b/arch/arm/boot/dts/am335x-bone-pinmux-nxp-hdmi.dtsi b/arch/arm/boot/dts/am335x-bone-pinmux-nxp-hdmi.dtsi new file mode 100644 index 000000000..5205fa0f9 --- /dev/null +++ b/arch/arm/boot/dts/am335x-bone-pinmux-nxp-hdmi.dtsi @@ -0,0 +1,120 @@ +/* + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include "am335x-peripheral-nxp-hdmi.dtsi" + +/* cape universal */ + +/* + *&ocp { + * P8_27_pinmux { + * state = "disabled"; + * }; + * P8_28_pinmux { + * state = "disabled"; + * }; + * P8_29_pinmux { + * state = "disabled"; + * }; + * P8_30_pinmux { + * state = "disabled"; + * }; + * P8_31_pinmux { + * state = "disabled"; + * }; + * P8_32_pinmux { + * state = "disabled"; + * }; + * P8_33_pinmux { + * state = "disabled"; + * }; + * P8_34_pinmux { + * state = "disabled"; + * }; + * P8_35_pinmux { + * state = "disabled"; + * }; + * P8_36_pinmux { + * state = "disabled"; + * }; + * P8_37_pinmux { + * state = "disabled"; + * }; + * P8_38_pinmux { + * state = "disabled"; + * }; + * P8_39_pinmux { + * state = "disabled"; + * }; + * P8_40_pinmux { + * state = "disabled"; + * }; + * P8_41_pinmux { + * state = "disabled"; + * }; + * P8_42_pinmux { + * state = "disabled"; + * }; + * P8_43_pinmux { + * state = "disabled"; + * }; + * P8_44_pinmux { + * state = "disabled"; + * }; + * P8_45_pinmux { + * state = "disabled"; + * }; + * P8_46_pinmux { + * state = "disabled"; + * }; + *}; + */ + +/* standard */ + +&am33xx_pinmux { + nxp_hdmi_pins: pinmux_nxp_hdmi_pins { + pinctrl-single,pins = < + AM33XX_IOPAD(0x9b0, PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* xdma_event_intr0 */ + AM33XX_IOPAD(0x8a0, PIN_OUTPUT | MUX_MODE0) /* lcd_data0.lcd_data0 */ + AM33XX_IOPAD(0x8a4, PIN_OUTPUT | MUX_MODE0) /* lcd_data1.lcd_data1 */ + AM33XX_IOPAD(0x8a8, PIN_OUTPUT | MUX_MODE0) /* lcd_data2.lcd_data2 */ + AM33XX_IOPAD(0x8ac, PIN_OUTPUT | MUX_MODE0) /* lcd_data3.lcd_data3 */ + AM33XX_IOPAD(0x8b0, PIN_OUTPUT | MUX_MODE0) /* lcd_data4.lcd_data4 */ + AM33XX_IOPAD(0x8b4, PIN_OUTPUT | MUX_MODE0) /* lcd_data5.lcd_data5 */ + AM33XX_IOPAD(0x8b8, PIN_OUTPUT | MUX_MODE0) /* lcd_data6.lcd_data6 */ + AM33XX_IOPAD(0x8bc, PIN_OUTPUT | MUX_MODE0) /* lcd_data7.lcd_data7 */ + AM33XX_IOPAD(0x8c0, PIN_OUTPUT | MUX_MODE0) /* lcd_data8.lcd_data8 */ + AM33XX_IOPAD(0x8c4, PIN_OUTPUT | MUX_MODE0) /* lcd_data9.lcd_data9 */ + AM33XX_IOPAD(0x8c8, PIN_OUTPUT | MUX_MODE0) /* lcd_data10.lcd_data10 */ + AM33XX_IOPAD(0x8cc, PIN_OUTPUT | MUX_MODE0) /* lcd_data11.lcd_data11 */ + AM33XX_IOPAD(0x8d0, PIN_OUTPUT | MUX_MODE0) /* lcd_data12.lcd_data12 */ + AM33XX_IOPAD(0x8d4, PIN_OUTPUT | MUX_MODE0) /* lcd_data13.lcd_data13 */ + AM33XX_IOPAD(0x8d8, PIN_OUTPUT | MUX_MODE0) /* lcd_data14.lcd_data14 */ + AM33XX_IOPAD(0x8dc, PIN_OUTPUT | MUX_MODE0) /* lcd_data15.lcd_data15 */ + AM33XX_IOPAD(0x8e0, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* lcd_vsync.lcd_vsync */ + AM33XX_IOPAD(0x8e4, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* lcd_hsync.lcd_hsync */ + AM33XX_IOPAD(0x8e8, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* lcd_pclk.lcd_pclk */ + AM33XX_IOPAD(0x8ec, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* lcd_ac_bias_en.lcd_ac_bias_en */ + >; + }; + + nxp_hdmi_off_pins: nxp_hdmi_off_pins { + pinctrl-single,pins = < + AM33XX_IOPAD(0x9b0, PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* xdma_event_intr0 */ + >; + }; +}; + +&i2c0 { + tda19988 { + pinctrl-names = "default", "off"; + pinctrl-0 = <&nxp_hdmi_bonelt_pins>; + pinctrl-1 = <&nxp_hdmi_bonelt_off_pins>; + }; +}; diff --git b/arch/arm/boot/dts/am335x-bone-pinmux-panel-1024x600-24bit.dtsi b/arch/arm/boot/dts/am335x-bone-pinmux-panel-1024x600-24bit.dtsi new file mode 100644 index 000000000..65e5fbb0c --- /dev/null +++ b/arch/arm/boot/dts/am335x-bone-pinmux-panel-1024x600-24bit.dtsi @@ -0,0 +1,151 @@ +/* + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include +#include "am335x-peripheral-panel-1024x600-24bit.dtsi" + +/* cape universal */ + +/* + *&ocp { + * P8_27_pinmux { + * state = "disabled"; + * }; + * P8_28_pinmux { + * state = "disabled"; + * }; + * P8_29_pinmux { + * state = "disabled"; + * }; + * P8_30_pinmux { + * state = "disabled"; + * }; + * P8_31_pinmux { + * state = "disabled"; + * }; + * P8_32_pinmux { + * state = "disabled"; + * }; + * P8_33_pinmux { + * state = "disabled"; + * }; + * P8_34_pinmux { + * state = "disabled"; + * }; + * P8_35_pinmux { + * state = "disabled"; + * }; + * P8_36_pinmux { + * state = "disabled"; + * }; + * P8_37_pinmux { + * state = "disabled"; + * }; + * P8_38_pinmux { + * state = "disabled"; + * }; + * P8_39_pinmux { + * state = "disabled"; + * }; + * P8_40_pinmux { + * state = "disabled"; + * }; + * P8_41_pinmux { + * state = "disabled"; + * }; + * P8_42_pinmux { + * state = "disabled"; + * }; + * P8_43_pinmux { + * state = "disabled"; + * }; + * P8_44_pinmux { + * state = "disabled"; + * }; + * P8_45_pinmux { + * state = "disabled"; + * }; + * P8_46_pinmux { + * state = "disabled"; + * }; + *}; + */ + +/* standard */ + +&am33xx_pinmux { + lcd_24bit_pins: pinmux_lcd_24bit_pins { + pinctrl-single,pins = < + + /* P8_45: lcd_data0.lcd_data0 */ + BONE_P8_45 (PIN_OUTPUT | MUX_MODE0) + /* P8_46: lcd_data1.lcd_data1 */ + BONE_P8_46 (PIN_OUTPUT | MUX_MODE0) + /* P8_43: lcd_data2.lcd_data2 */ + BONE_P8_43 (PIN_OUTPUT | MUX_MODE0) + /* P8_44: lcd_data3.lcd_data3 */ + BONE_P8_44 (PIN_OUTPUT | MUX_MODE0) + /* P8_41: lcd_data4.lcd_data4 */ + BONE_P8_41 (PIN_OUTPUT | MUX_MODE0) + /* P8_42: lcd_data5.lcd_data5 */ + BONE_P8_42 (PIN_OUTPUT | MUX_MODE0) + /* P8_39: lcd_data6.lcd_data6 */ + BONE_P8_39 (PIN_OUTPUT | MUX_MODE0) + /* P8_40: lcd_data7.lcd_data7 */ + BONE_P8_40 (PIN_OUTPUT | MUX_MODE0) + /* P8_37: lcd_data8.lcd_data8 */ + BONE_P8_37 (PIN_OUTPUT | MUX_MODE0) + /* P8_38: lcd_data9.lcd_data9 */ + BONE_P8_38 (PIN_OUTPUT | MUX_MODE0) + /* P8_36: lcd_data10.lcd_data10 */ + BONE_P8_36 (PIN_OUTPUT | MUX_MODE0) + /* P8_34: lcd_data11.lcd_data11 */ + BONE_P8_34 (PIN_OUTPUT | MUX_MODE0) + /* P8_35: lcd_data12.lcd_data12 */ + BONE_P8_35 (PIN_OUTPUT | MUX_MODE0) + /* P8_33: lcd_data13.lcd_data13 */ + BONE_P8_33 (PIN_OUTPUT | MUX_MODE0) + /* P8_31: lcd_data14.lcd_data14 */ + BONE_P8_31 (PIN_OUTPUT | MUX_MODE0) + /* P8_32: lcd_data15.lcd_data15 */ + BONE_P8_32 (PIN_OUTPUT | MUX_MODE0) + + /* gpmc_ad15.lcd_data16 */ + BONE_P8_15 (PIN_OUTPUT | MUX_MODE1) + /* gpmc_ad14.lcd_data17 */ + BONE_P8_16 (PIN_OUTPUT | MUX_MODE1) + /* gpmc_ad13.lcd_data18 */ + BONE_P8_11 (PIN_OUTPUT | MUX_MODE1) + /* gpmc_ad12.lcd_data19 */ + BONE_P8_12 (PIN_OUTPUT | MUX_MODE1) + /* gpmc_ad11.lcd_data20 */ + BONE_P8_17 (PIN_OUTPUT | MUX_MODE1) + /* gpmc_ad10.lcd_data21 */ + BONE_P8_14 (PIN_OUTPUT | MUX_MODE1) + /* gpmc_ad9.lcd_data22 */ + BONE_P8_13 (PIN_OUTPUT | MUX_MODE1) + /* gpmc_ad8.lcd_data23 */ + BONE_P8_19 (PIN_OUTPUT | MUX_MODE1) + + /* P8_27: lcd_vsync.lcd_vsync */ + BONE_P8_27 (PIN_OUTPUT | MUX_MODE0) + /* P8_29: lcd_hsync.lcd_hsync */ + BONE_P8_29 (PIN_OUTPUT | MUX_MODE0) + /* P8_28: lcd_pclk.lcd_pclk*/ + BONE_P8_28 (PIN_OUTPUT | MUX_MODE0) + /* P8_30: lcd_ac_bias_en.lcd_ac_bias_en */ + BONE_P8_30 (PIN_OUTPUT | MUX_MODE0) + >; + }; +}; + +/ { + panel { + pinctrl-0 = <&lcd_24bit_pins>; + }; +}; diff --git b/arch/arm/boot/dts/am335x-bone-pinmux-spi0.dtsi b/arch/arm/boot/dts/am335x-bone-pinmux-spi0.dtsi new file mode 100644 index 000000000..354e66ad4 --- /dev/null +++ b/arch/arm/boot/dts/am335x-bone-pinmux-spi0.dtsi @@ -0,0 +1,51 @@ +/* + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include +#include "am335x-peripheral-spi0.dtsi" + +/* cape universal */ + +/* + *&ocp { + * P9_17_pinmux { + * status = "disabled"; + * }; + * P9_18_pinmux { + * status = "disabled"; + * }; + * P9_21_pinmux { + * status = "disabled"; + * }; + * P9_22_pinmux { + * status = "disabled"; + * }; + *}; + * + *&spi0 { + * pinctrl-0 = <>; + *}; + * + */ + +/* standard */ + +&am33xx_pinmux { + spi0_pins: pinmux_spi0_pins { + pinctrl-single,pins = < + 0x150 (PIN_INPUT_PULLUP | MUX_MODE0) /* spi0_sclk.spi0_sclk */ + 0x154 (PIN_INPUT_PULLUP | MUX_MODE0) /* spi0_d0.spi0_d0 */ + 0x158 (PIN_OUTPUT_PULLUP | MUX_MODE0) /* spi0_d1.spi0_d1 */ + 0x15c (PIN_OUTPUT_PULLUP | MUX_MODE0) /* spi0_cs0.spi0_cs0 */ + >; + }; +}; + +&spi0 { + pinctrl-0 = <&spi0_pins>; +}; diff --git b/arch/arm/boot/dts/am335x-bone-pinmux-spi1.dtsi b/arch/arm/boot/dts/am335x-bone-pinmux-spi1.dtsi new file mode 100644 index 000000000..bff7f8dae --- /dev/null +++ b/arch/arm/boot/dts/am335x-bone-pinmux-spi1.dtsi @@ -0,0 +1,27 @@ +/* + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include +#include "am335x-peripheral-spi1.dtsi" + +/* standard */ + +&am33xx_pinmux { + spi1_pins: pinmux_spi1_pins { + pinctrl-single,pins = < + 0x190 0x33 /* mcasp0_aclkx.spi1_sclk, INPUT_PULLUP | MODE3 */ + 0x194 0x33 /* mcasp0_fsx.spi1_d0, INPUT_PULLUP | MODE3 */ + 0x198 0x13 /* mcasp0_axr0.spi1_d1, OUTPUT_PULLUP | MODE3 */ + 0x19c 0x13 /* mcasp0_ahclkr.spi1_cs0, OUTPUT_PULLUP | MODE3 */ + // 0x164 0x12 /* eCAP0_in_PWM0_out.spi1_cs1 OUTPUT_PULLUP | MODE2 */ >; + }; +}; + +&spi1 { + pinctrl-0 = <&spi1_pins>; +}; diff --git b/arch/arm/boot/dts/am335x-bone-pinmux-spi1a.dtsi b/arch/arm/boot/dts/am335x-bone-pinmux-spi1a.dtsi new file mode 100644 index 000000000..62874c892 --- /dev/null +++ b/arch/arm/boot/dts/am335x-bone-pinmux-spi1a.dtsi @@ -0,0 +1,28 @@ +/* + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include +#include "am335x-peripheral-spi1.dtsi" + +/* standard */ + +&am33xx_pinmux { + spi1a_pins: pinmux_spi1a_pins { + pinctrl-single,pins = < + 0x164 0x34 /* eCAP0_in_PWM0_out.spi1_sclk, INPUT_PULLUP | MODE4 */ + /* NOTE: P9.42 is connected to two pads */ + // 0x1A0 0x27 /* set the other pad to gpio input */ + 0x194 0x33 /* mcasp0_fsx.spi1_d0, INPUT_PULLUP | MODE3 */ + 0x198 0x13 /* mcasp0_axr0.spi1_d1, OUTPUT_PULLUP | MODE3 */ + 0x178 0x14 /* uart1_ctsn.spi1_cs0, OUTPUT_PULLUP | MODE4 */ >; + }; +}; + +&spi1 { + pinctrl-0 = <&spi1a_pins>; +}; diff --git b/arch/arm/boot/dts/am335x-bone-pinmux-ttyS1.dtsi b/arch/arm/boot/dts/am335x-bone-pinmux-ttyS1.dtsi new file mode 100644 index 000000000..ae5b813f0 --- /dev/null +++ b/arch/arm/boot/dts/am335x-bone-pinmux-ttyS1.dtsi @@ -0,0 +1,48 @@ +/* + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +/* Testing */ +/* sudo /sbin/getty -L ttyS1 115200 vt102 */ + +#include +#include "am335x-peripheral-ttyS1.dtsi" + +/* cape universal */ + +/* + *&ocp { + * P9_24_pinmux { + * mode = "uart"; + * }; + * P9_26_pinmux { + * mode = "uart"; + * }; + *}; + * + *&uart1 { + * pinctrl-0 = <>; + *}; + * + */ + +/* standard */ + +&am33xx_pinmux { + uart1_pins: pinmux_uart1_pins { + pinctrl-single,pins = < + /* P9_24: uart1_txd.uart1_txd */ + BONE_P9_24 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) + /* P9_26: uart1_rxd.uart1_rxd */ + BONE_P9_26 (PIN_INPUT_PULLUP | MUX_MODE0) + >; + }; +}; + +&uart1 { + pinctrl-0 = <&uart1_pins>; +}; diff --git b/arch/arm/boot/dts/am335x-bone-pinmux-ttyS2.dtsi b/arch/arm/boot/dts/am335x-bone-pinmux-ttyS2.dtsi new file mode 100644 index 000000000..5fa593ac3 --- /dev/null +++ b/arch/arm/boot/dts/am335x-bone-pinmux-ttyS2.dtsi @@ -0,0 +1,48 @@ +/* + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +/* Testing */ +/* sudo /sbin/getty -L ttyS2 115200 vt102 */ + +#include +#include "am335x-peripheral-ttyS2.dtsi" + +/* cape universal */ + +/* + *&ocp { + * P9_21_pinmux { + * mode = "uart"; + * }; + * P9_22_pinmux { + * mode = "uart"; + * }; + *}; + * + *&uart2 { + * pinctrl-0 = <>; + *}; + * + */ + +/* standard */ + +&am33xx_pinmux { + uart2_pins: pinmux_uart2_pins { + pinctrl-single,pins = < + /* P9_21: spi0_d0.uart2_txd */ + BONE_P9_21 (PIN_OUTPUT_PULLDOWN | MUX_MODE1) + /* P9_22: spi0_sclk.uart2_rxd */ + BONE_P9_22 (PIN_INPUT_PULLUP | MUX_MODE1) + >; + }; +}; + +&uart2 { + pinctrl-0 = <&uart2_pins>; +}; diff --git b/arch/arm/boot/dts/am335x-bone-pinmux-ttyS4.dtsi b/arch/arm/boot/dts/am335x-bone-pinmux-ttyS4.dtsi new file mode 100644 index 000000000..1d22a95a2 --- /dev/null +++ b/arch/arm/boot/dts/am335x-bone-pinmux-ttyS4.dtsi @@ -0,0 +1,48 @@ +/* + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +/* Testing */ +/* sudo /sbin/getty -L ttyS4 115200 vt102 */ + +#include +#include "am335x-peripheral-ttyS4.dtsi" + +/* cape universal */ + +/* + *&ocp { + * P9_11_pinmux { + * mode = "uart"; + * }; + * P9_13_pinmux { + * mode = "uart"; + * }; + *}; + * + *&uart4 { + * pinctrl-0 = <>; + *}; + * + */ + +/* standard */ + +&am33xx_pinmux { + uart4_pins: pinmux_uart4_pins { + pinctrl-single,pins = < + /* P9_11: gpmc_wait0.uart4_rxd_mux2 */ + BONE_P9_11 (PIN_INPUT_PULLUP | MUX_MODE6) + /* P9_13: gpmc_wpn.uart4_txd_mux2 */ + BONE_P9_13 (PIN_OUTPUT_PULLDOWN | MUX_MODE6) + >; + }; +}; + +&uart4 { + pinctrl-0 = <&uart4_pins>; +}; diff --git b/arch/arm/boot/dts/am335x-bone-pinmux-ttyS5.dtsi b/arch/arm/boot/dts/am335x-bone-pinmux-ttyS5.dtsi new file mode 100644 index 000000000..01d0aec1d --- /dev/null +++ b/arch/arm/boot/dts/am335x-bone-pinmux-ttyS5.dtsi @@ -0,0 +1,48 @@ +/* + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +/* Testing */ +/* sudo /sbin/getty -L ttyS5 115200 vt102 */ + +#include +#include "am335x-peripheral-ttyS5.dtsi" + +/* cape universal */ + +/* + *&ocp { + * P8_37_pinmux { + * mode = "uart"; + * }; + * P8_38_pinmux { + * mode = "uart"; + * }; + *}; + * + *&uart5 { + * pinctrl-0 = <>; + *}; + * + */ + +/* standard */ + +&am33xx_pinmux { + uart5_pins: pinmux_uart5_pins { + pinctrl-single,pins = < + /* P8_38: lcd_data9.uart5_rxd */ + BONE_P8_38 (PIN_INPUT_PULLUP | MUX_MODE4) + /* P8_37: lcd_data8.uart5_txd */ + BONE_P8_37 (PIN_OUTPUT_PULLDOWN | MUX_MODE4) + >; + }; +}; + +&uart5 { + pinctrl-0 = <&uart5_pins>; +}; diff --git a/arch/arm/boot/dts/am335x-bone.dts b/arch/arm/boot/dts/am335x-bone.dts index 6b8493720..3688fff0a 100644 --- a/arch/arm/boot/dts/am335x-bone.dts +++ b/arch/arm/boot/dts/am335x-bone.dts @@ -9,6 +9,7 @@ #include "am33xx.dtsi" #include "am335x-bone-common.dtsi" +/* #include "am335x-bone-jtag.dtsi" */ / { model = "TI AM335x BeagleBone"; diff --git b/arch/arm/boot/dts/am335x-boneblack-audio.dts b/arch/arm/boot/dts/am335x-boneblack-audio.dts new file mode 100644 index 000000000..cac3626dd --- /dev/null +++ b/arch/arm/boot/dts/am335x-boneblack-audio.dts @@ -0,0 +1,39 @@ +/* + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +/dts-v1/; + +#include "am33xx.dtsi" +#include "am335x-bone-common.dtsi" + +/ { + model = "TI AM335x BeagleBone Black"; + compatible = "ti,am335x-bone-black", "ti,am335x-bone", "ti,am33xx"; + + clk_mcasp0_fixed: clk_mcasp0_fixed { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <24576000>; + }; + + clk_mcasp0: clk_mcasp0 { + #clock-cells = <0>; + compatible = "gpio-gate-clock"; + clocks = <&clk_mcasp0_fixed>; + enable-gpios = <&gpio1 27 GPIO_ACTIVE_HIGH>; /* BeagleBone Black Clk enable on GPIO1_27 */ + }; +}; + +&ldo3_reg { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; +}; + +&mmc1 { + vmmc-supply = <&vmmcsd_fixed>; +}; diff --git b/arch/arm/boot/dts/am335x-boneblack-bbb-exp-c.dts b/arch/arm/boot/dts/am335x-boneblack-bbb-exp-c.dts new file mode 100644 index 000000000..8d795c065 --- /dev/null +++ b/arch/arm/boot/dts/am335x-boneblack-bbb-exp-c.dts @@ -0,0 +1,47 @@ +/* + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +/dts-v1/; + +#include "am33xx.dtsi" +#include "am335x-bone-common-no-capemgr.dtsi" + +/ { + model = "TI AM335x BeagleBone Black"; + compatible = "ti,am335x-bone-black", "ti,am335x-bone", "ti,am33xx"; +}; + +&ldo3_reg { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; +}; + +&mmc1 { + vmmc-supply = <&vmmcsd_fixed>; +}; + +&mmc2 { + vmmc-supply = <&vmmcsd_fixed>; + pinctrl-names = "default"; + pinctrl-0 = <&emmc_pins>; + bus-width = <8>; + status = "okay"; +}; + +&cpu0_opp_table { + /* + * All PG 2.0 silicon may not support 1GHz but some of the early + * BeagleBone Blacks have PG 2.0 silicon which is guaranteed + * to support 1GHz OPP so enable it for PG 2.0 on this board. + */ + oppnitro@1000000000 { + opp-supported-hw = <0x06 0x0100>; + }; +}; + +#include "am335x-cape-bbb-exp-c.dtsi" diff --git b/arch/arm/boot/dts/am335x-boneblack-bbb-exp-r.dts b/arch/arm/boot/dts/am335x-boneblack-bbb-exp-r.dts new file mode 100644 index 000000000..5df881eaa --- /dev/null +++ b/arch/arm/boot/dts/am335x-boneblack-bbb-exp-r.dts @@ -0,0 +1,47 @@ +/* + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +/dts-v1/; + +#include "am33xx.dtsi" +#include "am335x-bone-common-no-capemgr.dtsi" + +/ { + model = "TI AM335x BeagleBone Black"; + compatible = "ti,am335x-bone-black", "ti,am335x-bone", "ti,am33xx"; +}; + +&ldo3_reg { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; +}; + +&mmc1 { + vmmc-supply = <&vmmcsd_fixed>; +}; + +&mmc2 { + vmmc-supply = <&vmmcsd_fixed>; + pinctrl-names = "default"; + pinctrl-0 = <&emmc_pins>; + bus-width = <8>; + status = "okay"; +}; + +&cpu0_opp_table { + /* + * All PG 2.0 silicon may not support 1GHz but some of the early + * BeagleBone Blacks have PG 2.0 silicon which is guaranteed + * to support 1GHz OPP so enable it for PG 2.0 on this board. + */ + oppnitro@1000000000 { + opp-supported-hw = <0x06 0x0100>; + }; +}; + +#include "am335x-cape-bbb-exp-r.dtsi" diff --git b/arch/arm/boot/dts/am335x-boneblack-bbbmini.dts b/arch/arm/boot/dts/am335x-boneblack-bbbmini.dts new file mode 100644 index 000000000..5ed89a2b1 --- /dev/null +++ b/arch/arm/boot/dts/am335x-boneblack-bbbmini.dts @@ -0,0 +1,207 @@ +/* + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ + * Modified by Mirko Denecke + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +/dts-v1/; + +#include "am33xx.dtsi" +#include "am335x-bone-common.dtsi" + +#include +#include + +/ { + model = "TI AM335x BeagleBone Black"; + compatible = "ti,am335x-bone-black", "ti,am335x-bone", "ti,am33xx"; +}; + +&ldo3_reg { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; +}; + +&mmc1 { + vmmc-supply = <&vmmcsd_fixed>; +}; + +&mmc2 { + vmmc-supply = <&vmmcsd_fixed>; + pinctrl-names = "default"; + pinctrl-0 = <&emmc_pins>; + bus-width = <8>; + status = "okay"; +}; + +&cpu0_opp_table { + /* + * All PG 2.0 silicon may not support 1GHz but some of the early + * BeagleBone Blacks have PG 2.0 silicon which is guaranteed + * to support 1GHz OPP so enable it for PG 2.0 on this board. + */ + oppnitro@1000000000 { + opp-supported-hw = <0x06 0x0100>; + }; +}; + +&am33xx_pinmux { + dcan1_pins: pinmux_dcan1_pins { + pinctrl-single,pins = < + /* P9_26: uart1_rxd.d_can1_tx */ + BONE_P9_26 (PIN_OUTPUT_PULLUP | MUX_MODE2) + /* P9_24: uart1_txd.d_can1_rx */ + BONE_P9_24 (PIN_INPUT_PULLUP | MUX_MODE2) + >; + }; + + pru_pins: pinmux_pru_pins { + pinctrl-single,pins = < + 0x03c 0x35 /* ecap0_in_pwm0_out.pr1_ecap0_ecap_capin, MODE5 | INPUT_PULLUP | PRU, PPM-sum, SBUS, DSM */ + + 0x0e8 0x25 /* lcd_pclk.pr1_pru1_pru_r30_10, MODE5 | OUTPUT | PRU, CH_1 */ + 0x0e0 0x25 /* lcd_vsync.pr1_pru1_pru_r30_8, MODE5 | OUTPUT | PRU, CH_2 */ + 0x0ec 0x25 /* lcd_ac_bias_en.pr1_pru1_pru_r30_11, MODE5 | OUTPUT | PRU, CH_3 */ + 0x0e4 0x25 /* lcd_hsync.pr1_pru1_pru_r30_9, MODE5 | OUTPUT | PRU, CH_4 */ + 0x0bc 0x25 /* lcd_data7.pr1_pru1_pru_r30_7, MODE5 | OUTPUT | PRU, CH_5 */ + 0x0b8 0x25 /* lcd_data6.pr1_pru1_pru_r30_6, MODE5 | OUTPUT | PRU, CH_6 */ + 0x0b4 0x25 /* lcd_data5.pr1_pru1_pru_r30_5, MODE5 | OUTPUT | PRU, CH_7 */ + 0x0b0 0x25 /* lcd_data4.pr1_pru1_pru_r30_4, MODE5 | OUTPUT | PRU, CH_8 */ + 0x0ac 0x25 /* lcd_data3.pr1_pru1_pru_r30_3, MODE5 | OUTPUT | PRU, CH_9 */ + 0x0a8 0x25 /* lcd_data2.pr1_pru1_pru_r30_2, MODE5 | OUTPUT | PRU, CH_10 */ + 0x0a4 0x25 /* lcd_data1.pr1_pru1_pru_r30_1, MODE5 | OUTPUT | PRU, CH_11 */ + 0x0a0 0x25 /* lcd_data0.pr1_pru1_pru_r30_0, MODE5 | OUTPUT | PRU, CH_12 */ + + BONE_P8_12 (PIN_OUTPUT_PULLDOWN | MUX_MODE6) /* HC-SR04 TRIG */ + BONE_P8_16 (PIN_INPUT_PULLDOWN | MUX_MODE6) /* HC-SR04 ECHO */ + + BONE_P9_25 (PIN_INPUT_PULLDOWN | MUX_MODE6) /* MPU9250 INT */ + >; + }; + + spi0_pins: pinmux_spi0_pins { + pinctrl-single,pins = < + /* P9_22: spi0_sclk.spi0_sclk */ + BONE_P9_22 (PIN_INPUT_PULLUP | MUX_MODE0) + /* P9_21: spi0_d0.spi0_d0 */ + BONE_P9_21 (PIN_INPUT_PULLUP | MUX_MODE0) + /* P9_18: spi0_d1.spi0_d1 */ + BONE_P9_18 (PIN_OUTPUT_PULLUP | MUX_MODE0) + /* P9_17: spi0_cs0.spi0_cs0 */ + BONE_P9_17 (PIN_OUTPUT_PULLUP | MUX_MODE0) + >; + }; + + spi1_pins: pinmux_spi1_pins { + pinctrl-single,pins = < + /* P9_31: mcasp0_aclkx.spi1_sclk */ + BONE_P9_31 (PIN_INPUT_PULLUP | MUX_MODE3) + + /* P9_29: mcasp0_fsx.spi1_d0 */ + BONE_P9_29 (PIN_INPUT_PULLUP | MUX_MODE3) + + /* P9_30: mcasp0_axr0.spi1_d1 */ + BONE_P9_30 (PIN_OUTPUT_PULLUP | MUX_MODE3) + + /* P9_28: mcasp0_ahclkr.spi1_cs0 */ + BONE_P9_28 (PIN_OUTPUT_PULLUP | MUX_MODE3) + + /* P9_19: uart1_rtsn.spi1_cs1 */ +/* BONE_P9_19 (PIN_OUTPUT_PULLUP | MUX_MODE4)*/ + + /* P9_42: ecap0_in_pwm0_out.spi1_cs1 */ + BONE_P9_42A (PIN_OUTPUT_PULLUP | MUX_MODE2) + >; + }; + + uart4_pins: pinmux_uart4_pins { + pinctrl-single,pins = < + /* P9_11: gpmc_wait0.uart4_rxd_mux2 */ + BONE_P9_11 (PIN_INPUT_PULLUP | MUX_MODE6) + /* P9_13: gpmc_wpn.uart4_txd_mux2 */ + BONE_P9_13 (PIN_OUTPUT_PULLDOWN | MUX_MODE6) + >; + }; + + uart5_pins: pinmux_uart5_pins { + pinctrl-single,pins = < + /* P8_38: lcd_data9.uart5_rxd */ + BONE_P8_38 (PIN_INPUT_PULLUP | MUX_MODE4) + /* P8_37: lcd_data8.uart5_txd */ + BONE_P8_37 (PIN_OUTPUT_PULLDOWN | MUX_MODE4) + >; + }; +}; + +&dcan1 { + pinctrl-names = "default"; + pinctrl-0 = <&dcan1_pins>; + status = "okay"; +}; + +&i2c2 { + clock-frequency = <400000>; +}; + +&spi0 { + pinctrl-names = "default"; + pinctrl-0 = <&spi0_pins>; + status = "okay"; + + spi0_0 { + #address-cells = <1>; + #size-cells = <0>; + spi-max-frequency = <24000000>; + reg = <0>; + compatible = "spidev"; + }; +}; + +&spi1 { + pinctrl-names = "default"; + pinctrl-0 = <&spi1_pins>; + status = "okay"; + + spi1_0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + spi-max-frequency = <24000000>; + compatible = "spidev"; + }; + + spi1_1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + spi-max-frequency = <24000000>; + compatible = "spidev"; + }; +}; + +&tscadc { + adc { + ti,adc-channels = <0 1>; + }; +}; + +&pruss { + pinctrl-names = "default"; + pinctrl-0 = <&pru_pins>; + status = "okay"; +}; + +&uart4 { + pinctrl-names = "default"; + pinctrl-0 = <&uart4_pins>; + status = "okay"; +}; + +&uart5 { + pinctrl-names = "default"; + pinctrl-0 = <&uart5_pins>; + status = "okay"; +}; diff --git b/arch/arm/boot/dts/am335x-boneblack-cape-bone-argus.dts b/arch/arm/boot/dts/am335x-boneblack-cape-bone-argus.dts new file mode 100644 index 000000000..c97c912a7 --- /dev/null +++ b/arch/arm/boot/dts/am335x-boneblack-cape-bone-argus.dts @@ -0,0 +1,105 @@ +/* + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +/dts-v1/; + +#include "am33xx.dtsi" +#include "am335x-bone-common-no-capemgr.dtsi" + +/ { + model = "TI AM335x BeagleBone Black"; + compatible = "ti,am335x-bone-black", "ti,am335x-bone", "ti,am33xx"; +}; + +&ldo3_reg { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; +}; + +&mmc1 { + vmmc-supply = <&vmmcsd_fixed>; +}; + +&mmc2 { + vmmc-supply = <&vmmcsd_fixed>; + pinctrl-names = "default"; + pinctrl-0 = <&emmc_pins>; + bus-width = <8>; + status = "okay"; +}; + +&cpu0_opp_table { + /* + * All PG 2.0 silicon may not support 1GHz but some of the early + * BeagleBone Blacks have PG 2.0 silicon which is guaranteed + * to support 1GHz OPP so enable it for PG 2.0 on this board. + */ + oppnitro@1000000000 { + opp-supported-hw = <0x06 0x0100>; + }; +}; + +&am33xx_pinmux { + nxp_hdmi_bonelt_pins: nxp_hdmi_bonelt_pins { + pinctrl-single,pins = < + AM33XX_IOPAD(0x9b0, PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* xdma_event_intr0 */ + AM33XX_IOPAD(0x8a0, PIN_OUTPUT | MUX_MODE0) /* lcd_data0.lcd_data0 */ + AM33XX_IOPAD(0x8a4, PIN_OUTPUT | MUX_MODE0) /* lcd_data1.lcd_data1 */ + AM33XX_IOPAD(0x8a8, PIN_OUTPUT | MUX_MODE0) /* lcd_data2.lcd_data2 */ + AM33XX_IOPAD(0x8ac, PIN_OUTPUT | MUX_MODE0) /* lcd_data3.lcd_data3 */ + AM33XX_IOPAD(0x8b0, PIN_OUTPUT | MUX_MODE0) /* lcd_data4.lcd_data4 */ + AM33XX_IOPAD(0x8b4, PIN_OUTPUT | MUX_MODE0) /* lcd_data5.lcd_data5 */ + AM33XX_IOPAD(0x8b8, PIN_OUTPUT | MUX_MODE0) /* lcd_data6.lcd_data6 */ + AM33XX_IOPAD(0x8bc, PIN_OUTPUT | MUX_MODE0) /* lcd_data7.lcd_data7 */ + AM33XX_IOPAD(0x8c0, PIN_OUTPUT | MUX_MODE0) /* lcd_data8.lcd_data8 */ + AM33XX_IOPAD(0x8c4, PIN_OUTPUT | MUX_MODE0) /* lcd_data9.lcd_data9 */ + AM33XX_IOPAD(0x8c8, PIN_OUTPUT | MUX_MODE0) /* lcd_data10.lcd_data10 */ + AM33XX_IOPAD(0x8cc, PIN_OUTPUT | MUX_MODE0) /* lcd_data11.lcd_data11 */ + AM33XX_IOPAD(0x8d0, PIN_OUTPUT | MUX_MODE0) /* lcd_data12.lcd_data12 */ + AM33XX_IOPAD(0x8d4, PIN_OUTPUT | MUX_MODE0) /* lcd_data13.lcd_data13 */ + AM33XX_IOPAD(0x8d8, PIN_OUTPUT | MUX_MODE0) /* lcd_data14.lcd_data14 */ + AM33XX_IOPAD(0x8dc, PIN_OUTPUT | MUX_MODE0) /* lcd_data15.lcd_data15 */ + AM33XX_IOPAD(0x8e0, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* lcd_vsync.lcd_vsync */ + AM33XX_IOPAD(0x8e4, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* lcd_hsync.lcd_hsync */ + AM33XX_IOPAD(0x8e8, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* lcd_pclk.lcd_pclk */ + AM33XX_IOPAD(0x8ec, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* lcd_ac_bias_en.lcd_ac_bias_en */ + >; + }; + nxp_hdmi_bonelt_off_pins: nxp_hdmi_bonelt_off_pins { + pinctrl-single,pins = < + AM33XX_IOPAD(0x9b0, PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* xdma_event_intr0 */ + >; + }; +}; + +&lcdc { + status = "okay"; + port { + lcdc_0: endpoint@0 { + remote-endpoint = <&hdmi_0>; + }; + }; +}; + +&i2c0 { + tda19988 { + compatible = "nxp,tda998x"; + reg = <0x70>; + pinctrl-names = "default", "off"; + pinctrl-0 = <&nxp_hdmi_bonelt_pins>; + pinctrl-1 = <&nxp_hdmi_bonelt_off_pins>; + + port { + hdmi_0: endpoint@0 { + remote-endpoint = <&lcdc_0>; + }; + }; + }; +}; + +#include "am335x-bone-argus.dtsi" diff --git b/arch/arm/boot/dts/am335x-boneblack-emmc-overlay.dts b/arch/arm/boot/dts/am335x-boneblack-emmc-overlay.dts new file mode 100644 index 000000000..ccd358ea4 --- /dev/null +++ b/arch/arm/boot/dts/am335x-boneblack-emmc-overlay.dts @@ -0,0 +1,47 @@ +/* + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +/dts-v1/; + +#include "am33xx.dtsi" +#include "am335x-bone-common.dtsi" +/* #include */ +/* #include "am335x-bone-jtag.dtsi" */ + +/ { + model = "TI AM335x BeagleBone Black"; + compatible = "ti,am335x-bone-black", "ti,am335x-bone", "ti,am33xx"; +}; + +&ldo3_reg { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; +}; + +&mmc1 { + vmmc-supply = <&vmmcsd_fixed>; +}; + +&mmc2 { + vmmc-supply = <&vmmcsd_fixed>; + pinctrl-names = "default"; + pinctrl-0 = <&emmc_pins>; + bus-width = <8>; + status = "okay"; +}; + +&cpu0_opp_table { + /* + * All PG 2.0 silicon may not support 1GHz but some of the early + * BeagleBone Blacks have PG 2.0 silicon which is guaranteed + * to support 1GHz OPP so enable it for PG 2.0 on this board. + */ + oppnitro@1000000000 { + opp-supported-hw = <0x06 0x0100>; + }; +}; diff --git b/arch/arm/boot/dts/am335x-boneblack-hdmi-overlay.dts b/arch/arm/boot/dts/am335x-boneblack-hdmi-overlay.dts new file mode 100644 index 000000000..0582e572a --- /dev/null +++ b/arch/arm/boot/dts/am335x-boneblack-hdmi-overlay.dts @@ -0,0 +1,169 @@ +/* + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +/dts-v1/; + +#include "am33xx.dtsi" +#include "am335x-bone-common.dtsi" +#include +/* #include "am335x-bone-jtag.dtsi" */ + +/ { + model = "TI AM335x BeagleBone Black"; + compatible = "ti,am335x-bone-black", "ti,am335x-bone", "ti,am33xx"; +}; + +&ldo3_reg { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; +}; + +&mmc1 { + vmmc-supply = <&vmmcsd_fixed>; +}; + +/* EMMC in reset */ +&gpio1 { + emmc_rst { + gpio-hog; + gpios = <20 0>; + output-high; + line-name = "EMMC ResetN"; + }; +}; + +&cpu0_opp_table { + /* + * All PG 2.0 silicon may not support 1GHz but some of the early + * BeagleBone Blacks have PG 2.0 silicon which is guaranteed + * to support 1GHz OPP so enable it for PG 2.0 on this board. + */ + oppnitro@1000000000 { + opp-supported-hw = <0x06 0x0100>; + }; +}; + +&am33xx_pinmux { + nxp_hdmi_bonelt_pins: nxp_hdmi_bonelt_pins { + pinctrl-single,pins = < + AM33XX_IOPAD(0x9b0, PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* xdma_event_intr0 */ + AM33XX_IOPAD(0x8a0, PIN_OUTPUT | MUX_MODE0) /* lcd_data0.lcd_data0 */ + AM33XX_IOPAD(0x8a4, PIN_OUTPUT | MUX_MODE0) /* lcd_data1.lcd_data1 */ + AM33XX_IOPAD(0x8a8, PIN_OUTPUT | MUX_MODE0) /* lcd_data2.lcd_data2 */ + AM33XX_IOPAD(0x8ac, PIN_OUTPUT | MUX_MODE0) /* lcd_data3.lcd_data3 */ + AM33XX_IOPAD(0x8b0, PIN_OUTPUT | MUX_MODE0) /* lcd_data4.lcd_data4 */ + AM33XX_IOPAD(0x8b4, PIN_OUTPUT | MUX_MODE0) /* lcd_data5.lcd_data5 */ + AM33XX_IOPAD(0x8b8, PIN_OUTPUT | MUX_MODE0) /* lcd_data6.lcd_data6 */ + AM33XX_IOPAD(0x8bc, PIN_OUTPUT | MUX_MODE0) /* lcd_data7.lcd_data7 */ + AM33XX_IOPAD(0x8c0, PIN_OUTPUT | MUX_MODE0) /* lcd_data8.lcd_data8 */ + AM33XX_IOPAD(0x8c4, PIN_OUTPUT | MUX_MODE0) /* lcd_data9.lcd_data9 */ + AM33XX_IOPAD(0x8c8, PIN_OUTPUT | MUX_MODE0) /* lcd_data10.lcd_data10 */ + AM33XX_IOPAD(0x8cc, PIN_OUTPUT | MUX_MODE0) /* lcd_data11.lcd_data11 */ + AM33XX_IOPAD(0x8d0, PIN_OUTPUT | MUX_MODE0) /* lcd_data12.lcd_data12 */ + AM33XX_IOPAD(0x8d4, PIN_OUTPUT | MUX_MODE0) /* lcd_data13.lcd_data13 */ + AM33XX_IOPAD(0x8d8, PIN_OUTPUT | MUX_MODE0) /* lcd_data14.lcd_data14 */ + AM33XX_IOPAD(0x8dc, PIN_OUTPUT | MUX_MODE0) /* lcd_data15.lcd_data15 */ + AM33XX_IOPAD(0x8e0, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* lcd_vsync.lcd_vsync */ + AM33XX_IOPAD(0x8e4, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* lcd_hsync.lcd_hsync */ + AM33XX_IOPAD(0x8e8, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* lcd_pclk.lcd_pclk */ + AM33XX_IOPAD(0x8ec, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* lcd_ac_bias_en.lcd_ac_bias_en */ + >; + }; + nxp_hdmi_bonelt_off_pins: nxp_hdmi_bonelt_off_pins { + pinctrl-single,pins = < + AM33XX_IOPAD(0x9b0, PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* xdma_event_intr0 */ + >; + }; + + mcasp0_pins: mcasp0_pins { + pinctrl-single,pins = < + AM33XX_IOPAD(0x9ac, PIN_INPUT_PULLUP | MUX_MODE0) /* mcasp0_ahcklx.mcasp0_ahclkx */ + AM33XX_IOPAD(0x99c, PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mcasp0_ahclkr.mcasp0_axr2*/ + AM33XX_IOPAD(0x994, PIN_OUTPUT_PULLUP | MUX_MODE0) /* mcasp0_fsx.mcasp0_fsx */ + AM33XX_IOPAD(0x990, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mcasp0_aclkx.mcasp0_aclkx */ + AM33XX_IOPAD(0x86c, PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a11.GPIO1_27 */ + >; + }; +}; + +&lcdc { + status = "okay"; + port { + lcdc_0: endpoint@0 { + remote-endpoint = <&hdmi_0>; + }; + }; +}; + +&i2c0 { + tda19988: tda19988 { + compatible = "nxp,tda998x"; + reg = <0x70>; + + pinctrl-names = "default", "off"; + pinctrl-0 = <&nxp_hdmi_bonelt_pins>; + pinctrl-1 = <&nxp_hdmi_bonelt_off_pins>; + + #sound-dai-cells = <0>; + audio-ports = < TDA998x_I2S 0x03>; + + ports { + port@0 { + hdmi_0: endpoint@0 { + remote-endpoint = <&lcdc_0>; + }; + }; + }; + }; +}; + +&mcasp0 { + #sound-dai-cells = <0>; + pinctrl-names = "default"; + pinctrl-0 = <&mcasp0_pins>; + status = "okay"; + op-mode = <0>; /* MCASP_IIS_MODE */ + tdm-slots = <2>; + serial-dir = < /* 0: INACTIVE, 1: TX, 2: RX */ + 0 0 1 0 + >; + tx-num-evt = <32>; + rx-num-evt = <32>; +}; + +/ { + clk_mcasp0_fixed: clk_mcasp0_fixed { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <24576000>; + }; + + clk_mcasp0: clk_mcasp0 { + #clock-cells = <0>; + compatible = "gpio-gate-clock"; + clocks = <&clk_mcasp0_fixed>; + enable-gpios = <&gpio1 27 0>; /* BeagleBone Black Clk enable on GPIO1_27 */ + }; + + sound { + compatible = "simple-audio-card"; + simple-audio-card,name = "TI BeagleBone Black"; + simple-audio-card,format = "i2s"; + simple-audio-card,bitclock-master = <&dailink0_master>; + simple-audio-card,frame-master = <&dailink0_master>; + + dailink0_master: simple-audio-card,cpu { + sound-dai = <&mcasp0>; + clocks = <&clk_mcasp0>; + }; + + simple-audio-card,codec { + sound-dai = <&tda19988>; + }; + }; +}; diff --git b/arch/arm/boot/dts/am335x-boneblack-nhdmi-overlay.dts b/arch/arm/boot/dts/am335x-boneblack-nhdmi-overlay.dts new file mode 100644 index 000000000..c166c90a9 --- /dev/null +++ b/arch/arm/boot/dts/am335x-boneblack-nhdmi-overlay.dts @@ -0,0 +1,110 @@ +/* + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +/dts-v1/; + +#include "am33xx.dtsi" +#include "am335x-bone-common.dtsi" +#include +/* #include "am335x-bone-jtag.dtsi" */ + +/ { + model = "TI AM335x BeagleBone Black"; + compatible = "ti,am335x-bone-black", "ti,am335x-bone", "ti,am33xx"; +}; + +&ldo3_reg { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; +}; + +&mmc1 { + vmmc-supply = <&vmmcsd_fixed>; +}; + +/* EMMC in reset */ +&gpio1 { + emmc_rst { + gpio-hog; + gpios = <20 0>; + output-high; + line-name = "EMMC ResetN"; + }; +}; + +&cpu0_opp_table { + /* + * All PG 2.0 silicon may not support 1GHz but some of the early + * BeagleBone Blacks have PG 2.0 silicon which is guaranteed + * to support 1GHz OPP so enable it for PG 2.0 on this board. + */ + oppnitro@1000000000 { + opp-supported-hw = <0x06 0x0100>; + }; +}; + +&am33xx_pinmux { + nxp_hdmi_bonelt_pins: nxp_hdmi_bonelt_pins { + pinctrl-single,pins = < + AM33XX_IOPAD(0x9b0, PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* xdma_event_intr0 */ + AM33XX_IOPAD(0x8a0, PIN_OUTPUT | MUX_MODE0) /* lcd_data0.lcd_data0 */ + AM33XX_IOPAD(0x8a4, PIN_OUTPUT | MUX_MODE0) /* lcd_data1.lcd_data1 */ + AM33XX_IOPAD(0x8a8, PIN_OUTPUT | MUX_MODE0) /* lcd_data2.lcd_data2 */ + AM33XX_IOPAD(0x8ac, PIN_OUTPUT | MUX_MODE0) /* lcd_data3.lcd_data3 */ + AM33XX_IOPAD(0x8b0, PIN_OUTPUT | MUX_MODE0) /* lcd_data4.lcd_data4 */ + AM33XX_IOPAD(0x8b4, PIN_OUTPUT | MUX_MODE0) /* lcd_data5.lcd_data5 */ + AM33XX_IOPAD(0x8b8, PIN_OUTPUT | MUX_MODE0) /* lcd_data6.lcd_data6 */ + AM33XX_IOPAD(0x8bc, PIN_OUTPUT | MUX_MODE0) /* lcd_data7.lcd_data7 */ + AM33XX_IOPAD(0x8c0, PIN_OUTPUT | MUX_MODE0) /* lcd_data8.lcd_data8 */ + AM33XX_IOPAD(0x8c4, PIN_OUTPUT | MUX_MODE0) /* lcd_data9.lcd_data9 */ + AM33XX_IOPAD(0x8c8, PIN_OUTPUT | MUX_MODE0) /* lcd_data10.lcd_data10 */ + AM33XX_IOPAD(0x8cc, PIN_OUTPUT | MUX_MODE0) /* lcd_data11.lcd_data11 */ + AM33XX_IOPAD(0x8d0, PIN_OUTPUT | MUX_MODE0) /* lcd_data12.lcd_data12 */ + AM33XX_IOPAD(0x8d4, PIN_OUTPUT | MUX_MODE0) /* lcd_data13.lcd_data13 */ + AM33XX_IOPAD(0x8d8, PIN_OUTPUT | MUX_MODE0) /* lcd_data14.lcd_data14 */ + AM33XX_IOPAD(0x8dc, PIN_OUTPUT | MUX_MODE0) /* lcd_data15.lcd_data15 */ + AM33XX_IOPAD(0x8e0, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* lcd_vsync.lcd_vsync */ + AM33XX_IOPAD(0x8e4, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* lcd_hsync.lcd_hsync */ + AM33XX_IOPAD(0x8e8, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* lcd_pclk.lcd_pclk */ + AM33XX_IOPAD(0x8ec, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* lcd_ac_bias_en.lcd_ac_bias_en */ + >; + }; + nxp_hdmi_bonelt_off_pins: nxp_hdmi_bonelt_off_pins { + pinctrl-single,pins = < + AM33XX_IOPAD(0x9b0, PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* xdma_event_intr0 */ + >; + }; +}; + +&lcdc { + status = "okay"; + port { + lcdc_0: endpoint@0 { + remote-endpoint = <&hdmi_0>; + }; + }; +}; + +&i2c0 { + tda19988: tda19988 { + compatible = "nxp,tda998x"; + reg = <0x70>; + + pinctrl-names = "default", "off"; + pinctrl-0 = <&nxp_hdmi_bonelt_pins>; + pinctrl-1 = <&nxp_hdmi_bonelt_off_pins>; + + ports { + port@0 { + hdmi_0: endpoint@0 { + remote-endpoint = <&lcdc_0>; + }; + }; + }; + }; +}; diff --git b/arch/arm/boot/dts/am335x-boneblack-overlay.dts b/arch/arm/boot/dts/am335x-boneblack-overlay.dts new file mode 100644 index 000000000..e9bbd9397 --- /dev/null +++ b/arch/arm/boot/dts/am335x-boneblack-overlay.dts @@ -0,0 +1,49 @@ +/* + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +/dts-v1/; + +#include "am33xx.dtsi" +#include "am335x-bone-common.dtsi" +/* #include */ +/* #include "am335x-bone-jtag.dtsi" */ + +/ { + model = "TI AM335x BeagleBone Black"; + compatible = "ti,am335x-bone-black", "ti,am335x-bone", "ti,am33xx"; +}; + +&ldo3_reg { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; +}; + +&mmc1 { + vmmc-supply = <&vmmcsd_fixed>; +}; + +/* EMMC in reset */ +&gpio1 { + emmc_rst { + gpio-hog; + gpios = <20 0>; + output-high; + line-name = "EMMC ResetN"; + }; +}; + +&cpu0_opp_table { + /* + * All PG 2.0 silicon may not support 1GHz but some of the early + * BeagleBone Blacks have PG 2.0 silicon which is guaranteed + * to support 1GHz OPP so enable it for PG 2.0 on this board. + */ + oppnitro@1000000000 { + opp-supported-hw = <0x06 0x0100>; + }; +}; diff --git b/arch/arm/boot/dts/am335x-boneblack-roboticscape.dts b/arch/arm/boot/dts/am335x-boneblack-roboticscape.dts new file mode 100644 index 000000000..16e9376aa --- /dev/null +++ b/arch/arm/boot/dts/am335x-boneblack-roboticscape.dts @@ -0,0 +1,56 @@ +/* + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + + /****************************************************************************** + * This device tree serves to replace the need for an overlay when using + * the RoboticsCape. It is similar to the boneblue tree but preserves + * pin config for the black. + ******************************************************************************/ + + +/dts-v1/; + +#include "am33xx.dtsi" +#include "am335x-bone-common-no-capemgr.dtsi" +#include "am335x-bone-common-universal-pins.dtsi" +/* #include "am33xx-pruss-rproc.dtsi" */ +#include "am335x-roboticscape.dtsi" + +/ { + model = "TI AM335x BeagleBone Black"; + compatible = "ti,am335x-bone-black", "ti,am335x-bone", "ti,am33xx"; +}; + +&ldo3_reg { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; +}; + +&mmc1 { + vmmc-supply = <&vmmcsd_fixed>; +}; + +&mmc2 { + vmmc-supply = <&vmmcsd_fixed>; + pinctrl-names = "default"; + pinctrl-0 = <&emmc_pins>; + bus-width = <8>; + status = "okay"; +}; + +&cpu0_opp_table { + /* + * All PG 2.0 silicon may not support 1GHz but some of the early + * BeagleBone Blacks have PG 2.0 silicon which is guaranteed + * to support 1GHz OPP so enable it for PG 2.0 on this board. + */ + oppnitro@1000000000 { + opp-supported-hw = <0x06 0x0100>; + }; +}; diff --git b/arch/arm/boot/dts/am335x-boneblack-wireless-emmc-overlay.dts b/arch/arm/boot/dts/am335x-boneblack-wireless-emmc-overlay.dts new file mode 100644 index 000000000..78f63bf57 --- /dev/null +++ b/arch/arm/boot/dts/am335x-boneblack-wireless-emmc-overlay.dts @@ -0,0 +1,45 @@ +/* + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +/dts-v1/; + +#include "am33xx.dtsi" +#include "am335x-bone-common.dtsi" +/* #include */ +#include "am335x-boneblack-wl1835.dtsi" +/* #include "am335x-bone-jtag.dtsi" */ + +/ { + model = "TI AM335x BeagleBone Black Wireless"; + compatible = "ti,am335x-bone-black", "ti,am335x-bone", "ti,am33xx"; +}; + +&ldo3_reg { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; +}; + +&mmc1 { + vmmc-supply = <&vmmcsd_fixed>; +}; + +&mmc2 { + vmmc-supply = <&vmmcsd_fixed>; + pinctrl-names = "default"; + pinctrl-0 = <&emmc_pins>; + bus-width = <8>; + status = "okay"; +}; + +&mac { + status = "disabled"; +}; + +&mmc3 { + status = "okay"; +}; diff --git b/arch/arm/boot/dts/am335x-boneblack-wireless-roboticscape.dts b/arch/arm/boot/dts/am335x-boneblack-wireless-roboticscape.dts new file mode 100644 index 000000000..4a72d5640 --- /dev/null +++ b/arch/arm/boot/dts/am335x-boneblack-wireless-roboticscape.dts @@ -0,0 +1,46 @@ +/* + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + + /****************************************************************************** + * This device tree serves to replace the need for an overlay when using + * the RoboticsCape. It is similar to the boneblue tree but preserves + * pin config for the black. + ******************************************************************************/ + + +/dts-v1/; + +#include "am33xx.dtsi" +#include "am335x-bone-common-no-capemgr.dtsi" +#include "am335x-bone-common-universal-pins.dtsi" +/* #include "am33xx-pruss-rproc.dtsi" */ +#include "am335x-boneblack-wl1835.dtsi" +#include "am335x-roboticscape.dtsi" + +/ { + model = "TI AM335x BeagleBone Black Wireless"; + compatible = "ti,am335x-bone-black", "ti,am335x-bone", "ti,am33xx"; +}; + +&ldo3_reg { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; +}; + +&mmc1 { + vmmc-supply = <&vmmcsd_fixed>; +}; + +&mmc2 { + vmmc-supply = <&vmmcsd_fixed>; + pinctrl-names = "default"; + pinctrl-0 = <&emmc_pins>; + bus-width = <8>; + status = "okay"; +}; diff --git b/arch/arm/boot/dts/am335x-boneblack-wireless.dts b/arch/arm/boot/dts/am335x-boneblack-wireless.dts new file mode 100644 index 000000000..9b39648ef --- /dev/null +++ b/arch/arm/boot/dts/am335x-boneblack-wireless.dts @@ -0,0 +1,165 @@ +/* + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +/dts-v1/; + +#include "am33xx.dtsi" +#include "am335x-bone-common.dtsi" +#include +#include "am335x-boneblack-wl1835.dtsi" +/* #include "am335x-bone-jtag.dtsi" */ + +/ { + model = "TI AM335x BeagleBone Black Wireless"; + compatible = "ti,am335x-bone-black", "ti,am335x-bone", "ti,am33xx"; +}; + +&ldo3_reg { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; +}; + +&mmc1 { + vmmc-supply = <&vmmcsd_fixed>; +}; + +&mmc2 { + vmmc-supply = <&vmmcsd_fixed>; + pinctrl-names = "default"; + pinctrl-0 = <&emmc_pins>; + bus-width = <8>; + status = "okay"; +}; + +&mac { + status = "disabled"; +}; + +&mmc3 { + status = "okay"; +}; + +&am33xx_pinmux { + nxp_hdmi_bonelt_pins: nxp_hdmi_bonelt_pins { + pinctrl-single,pins = < + AM33XX_IOPAD(0x9b0, PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* xdma_event_intr0 */ + AM33XX_IOPAD(0x8a0, PIN_OUTPUT | MUX_MODE0) /* lcd_data0.lcd_data0 */ + AM33XX_IOPAD(0x8a4, PIN_OUTPUT | MUX_MODE0) /* lcd_data1.lcd_data1 */ + AM33XX_IOPAD(0x8a8, PIN_OUTPUT | MUX_MODE0) /* lcd_data2.lcd_data2 */ + AM33XX_IOPAD(0x8ac, PIN_OUTPUT | MUX_MODE0) /* lcd_data3.lcd_data3 */ + AM33XX_IOPAD(0x8b0, PIN_OUTPUT | MUX_MODE0) /* lcd_data4.lcd_data4 */ + AM33XX_IOPAD(0x8b4, PIN_OUTPUT | MUX_MODE0) /* lcd_data5.lcd_data5 */ + AM33XX_IOPAD(0x8b8, PIN_OUTPUT | MUX_MODE0) /* lcd_data6.lcd_data6 */ + AM33XX_IOPAD(0x8bc, PIN_OUTPUT | MUX_MODE0) /* lcd_data7.lcd_data7 */ + AM33XX_IOPAD(0x8c0, PIN_OUTPUT | MUX_MODE0) /* lcd_data8.lcd_data8 */ + AM33XX_IOPAD(0x8c4, PIN_OUTPUT | MUX_MODE0) /* lcd_data9.lcd_data9 */ + AM33XX_IOPAD(0x8c8, PIN_OUTPUT | MUX_MODE0) /* lcd_data10.lcd_data10 */ + AM33XX_IOPAD(0x8cc, PIN_OUTPUT | MUX_MODE0) /* lcd_data11.lcd_data11 */ + AM33XX_IOPAD(0x8d0, PIN_OUTPUT | MUX_MODE0) /* lcd_data12.lcd_data12 */ + AM33XX_IOPAD(0x8d4, PIN_OUTPUT | MUX_MODE0) /* lcd_data13.lcd_data13 */ + AM33XX_IOPAD(0x8d8, PIN_OUTPUT | MUX_MODE0) /* lcd_data14.lcd_data14 */ + AM33XX_IOPAD(0x8dc, PIN_OUTPUT | MUX_MODE0) /* lcd_data15.lcd_data15 */ + AM33XX_IOPAD(0x8e0, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* lcd_vsync.lcd_vsync */ + AM33XX_IOPAD(0x8e4, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* lcd_hsync.lcd_hsync */ + AM33XX_IOPAD(0x8e8, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* lcd_pclk.lcd_pclk */ + AM33XX_IOPAD(0x8ec, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* lcd_ac_bias_en.lcd_ac_bias_en */ + >; + }; + nxp_hdmi_bonelt_off_pins: nxp_hdmi_bonelt_off_pins { + pinctrl-single,pins = < + AM33XX_IOPAD(0x9b0, PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* xdma_event_intr0 */ + >; + }; + + mcasp0_pins: mcasp0_pins { + pinctrl-single,pins = < + AM33XX_IOPAD(0x9ac, PIN_INPUT_PULLUP | MUX_MODE0) /* mcasp0_ahcklx.mcasp0_ahclkx */ + AM33XX_IOPAD(0x99c, PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mcasp0_ahclkr.mcasp0_axr2*/ + AM33XX_IOPAD(0x994, PIN_OUTPUT_PULLUP | MUX_MODE0) /* mcasp0_fsx.mcasp0_fsx */ + AM33XX_IOPAD(0x990, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mcasp0_aclkx.mcasp0_aclkx */ + AM33XX_IOPAD(0x86c, PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a11.GPIO1_27 */ + >; + }; +}; + +&lcdc { + status = "okay"; + port { + lcdc_0: endpoint@0 { + remote-endpoint = <&hdmi_0>; + }; + }; +}; + +&i2c0 { + tda19988: tda19988 { + compatible = "nxp,tda998x"; + reg = <0x70>; + + pinctrl-names = "default", "off"; + pinctrl-0 = <&nxp_hdmi_bonelt_pins>; + pinctrl-1 = <&nxp_hdmi_bonelt_off_pins>; + + #sound-dai-cells = <0>; + audio-ports = < TDA998x_I2S 0x03>; + + ports { + port@0 { + hdmi_0: endpoint@0 { + remote-endpoint = <&lcdc_0>; + }; + }; + }; + }; +}; + +&mcasp0 { + #sound-dai-cells = <0>; + pinctrl-names = "default"; + pinctrl-0 = <&mcasp0_pins>; + status = "okay"; + op-mode = <0>; /* MCASP_IIS_MODE */ + tdm-slots = <2>; + serial-dir = < /* 0: INACTIVE, 1: TX, 2: RX */ + 0 0 1 0 + >; + tx-num-evt = <32>; + rx-num-evt = <32>; +}; + +/ { + clk_mcasp0_fixed: clk_mcasp0_fixed { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <24576000>; + }; + + clk_mcasp0: clk_mcasp0 { + #clock-cells = <0>; + compatible = "gpio-gate-clock"; + clocks = <&clk_mcasp0_fixed>; + enable-gpios = <&gpio1 27 0>; /* BeagleBone Black Clk enable on GPIO1_27 */ + }; + + sound { + compatible = "simple-audio-card"; + simple-audio-card,name = "TI BeagleBone Black"; + simple-audio-card,format = "i2s"; + simple-audio-card,bitclock-master = <&dailink0_master>; + simple-audio-card,frame-master = <&dailink0_master>; + + dailink0_master: simple-audio-card,cpu { + sound-dai = <&mcasp0>; + clocks = <&clk_mcasp0>; + }; + + simple-audio-card,codec { + sound-dai = <&tda19988>; + }; + }; +}; diff --git b/arch/arm/boot/dts/am335x-boneblack-wl1835.dtsi b/arch/arm/boot/dts/am335x-boneblack-wl1835.dtsi new file mode 100644 index 000000000..ec6c0e49a --- /dev/null +++ b/arch/arm/boot/dts/am335x-boneblack-wl1835.dtsi @@ -0,0 +1,143 @@ + +#include + +/ { + wlan_en_reg: fixedregulator@2 { + compatible = "regulator-fixed"; + regulator-name = "wlan-en-regulator"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + startup-delay-us= <70000>; + + /* WL_EN */ + gpio = <&gpio3 9 0>; + enable-active-high; + }; + + leds { + pinctrl-names = "default"; + pinctrl-0 = <&wl18xx_pins>; + compatible = "gpio-leds"; + + wl18xx_bt_en { + label = "wl18xx_bt_en"; + gpios = <&gpio0 28 GPIO_ACTIVE_HIGH>; + default-state = "off"; + }; + }; + + btwilink { + compatible = "btwilink"; + }; +}; + +&am33xx_pinmux { + wl18xx_pins: pinmux_wl18xx_pins { + pinctrl-single,pins = < + 0x128 (PIN_OUTPUT_PULLUP | MUX_MODE7) /* (K17) gmii1_txd0.gpio0[28] - BT_EN */ + >; + }; + + wlbtbuf_pin: pinmux_wlbtbuf_pin { + pinctrl-single,pins = < + 0x130 ( PIN_OUTPUT_PULLUP | MUX_MODE7 ) /* (L18) gmii1_rxclk.gpio3[10] - LS_BUF_EN */ + >; + }; + + mmc3_pins: pinmux_mmc3_pins { + pinctrl-single,pins = < + 0x13c ( PIN_INPUT_PULLUP | MUX_MODE6 ) /* (L15) gmii1_rxd1.mmc2_clk */ + 0x114 ( PIN_INPUT_PULLUP | MUX_MODE6 ) /* (J16) gmii1_txen.mmc2_cmd */ + 0x118 ( PIN_INPUT_PULLUP | MUX_MODE5 ) /* (J17) gmii1_rxdv.mmc2_dat0 */ + 0x11c ( PIN_INPUT_PULLUP | MUX_MODE5 ) /* (J18) gmii1_txd3.mmc2_dat1 */ + 0x120 ( PIN_INPUT_PULLUP | MUX_MODE5 ) /* (K15) gmii1_txd2.mmc2_dat2 */ + 0x108 ( PIN_INPUT_PULLUP | MUX_MODE5 ) /* (H16) gmii1_col.mmc2_dat3 */ + >; + }; + + mmc3_pins_sleep: pinmux_mmc3_pins_sleep { + pinctrl-single,pins = < + 0x13c ( PIN_INPUT_PULLDOWN | MUX_MODE6 ) /* (L15) gmii1_rxd1.mmc2_clk */ + 0x114 ( PIN_INPUT_PULLDOWN | MUX_MODE6 ) /* (J16) gmii1_txen.mmc2_cmd */ + 0x118 ( PIN_INPUT_PULLDOWN | MUX_MODE5 ) /* (J17) gmii1_rxdv.mmc2_dat0 */ + 0x11c ( PIN_INPUT_PULLDOWN | MUX_MODE5 ) /* (J18) gmii1_txd3.mmc2_dat1 */ + 0x120 ( PIN_INPUT_PULLDOWN | MUX_MODE5 ) /* (K15) gmii1_txd2.mmc2_dat2 */ + 0x108 ( PIN_INPUT_PULLDOWN | MUX_MODE5 ) /* (H16) gmii1_col.mmc2_dat3 */ + >; + }; + + /* wl18xx card enable/irq GPIOs. */ + wlan_pins: pinmux_wlan_pins { + pinctrl-single,pins = < + 0x12c (PIN_OUTPUT_PULLDOWN | MUX_MODE7 ) /* (K18) gmii1_txclk.gpio3[9] - WL_EN */ + 0x144 (PIN_INPUT_PULLDOWN | MUX_MODE7 ) /* (H18) rmii1_refclk.gpio0[29] - WL_IRQ */ + >; + }; + + /* wl18xx card enable/irq GPIOs. */ + wlan_pins_sleep: pinmux_wlan_pins_sleep { + pinctrl-single,pins = < + 0x12c (PIN_OUTPUT_PULLDOWN | MUX_MODE7 ) /* (K18) gmii1_txclk.gpio3[9] - WL_EN */ + 0x144 (PIN_INPUT_PULLDOWN | MUX_MODE7 ) /* (H18) rmii1_refclk.gpio0[29] - WL_IRQ */ + >; + }; + + uart3_pins_default: pinmux_uart3_pins_default { + pinctrl-single,pins = < + 0x134 ( PIN_INPUT_PULLUP | MUX_MODE1 ) /* (L17) gmii1_rxd3.uart3_rxd */ + 0x138 ( PIN_OUTPUT_PULLDOWN | MUX_MODE1 ) /* (L16) gmii1_rxd2.uart3_txd */ + 0x148 ( PIN_INPUT | MUX_MODE3 ) /* (M17) mdio_data.uart3_ctsn */ + 0x14c ( PIN_OUTPUT_PULLDOWN | MUX_MODE3 ) /* (M18) mdio_clk.uart3_rtsn */ + >; + }; + + uart3_pins_sleep: pinmux_uart3_pins_sleep { + pinctrl-single,pins = < + 0x134 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* (L17) gmii1_rxd3.uart3_rxd */ + 0x138 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* (L16) gmii1_rxd2.uart3_txd */ + 0x148 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* (M17) mdio_data.uart3_ctsn */ + 0x14c (PIN_INPUT_PULLDOWN | MUX_MODE7) /* (M18) mdio_clk.uart3_rtsn */ + >; + }; +}; + +&mmc3 { + dmas = <&edma_xbar 12 0 1 + &edma_xbar 13 0 2>; + dma-names = "tx", "rx"; + status = "okay"; + vmmc-supply = <&wlan_en_reg>; + bus-width = <4>; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&mmc3_pins &wlan_pins &wlbtbuf_pin>; + pinctrl-1 = <&mmc3_pins_sleep &wlan_pins_sleep &wlbtbuf_pin>; + ti,non-removable; + ti,needs-special-hs-handling; + cap-power-off-card; + keep-power-in-suspend; + + #address-cells = <1>; + #size-cells = <0>; + wlcore: wlcore@0 { + compatible = "ti,wl1835"; + reg = <2>; + interrupt-parent = <&gpio0>; + interrupts = <29 IRQ_TYPE_EDGE_RISING>; + }; +}; + +&uart3 { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&uart3_pins_default>; + pinctrl-1 = <&uart3_pins_sleep>; + status = "okay"; +}; + +&gpio3 { + ls_buf_en { + gpio-hog; + gpios = <10 GPIO_ACTIVE_HIGH>; + output-high; + line-name = "LS_BUF_EN"; + }; +}; diff --git b/arch/arm/boot/dts/am335x-boneblack-wl1835mod-cape.dtsi b/arch/arm/boot/dts/am335x-boneblack-wl1835mod-cape.dtsi new file mode 100644 index 000000000..94caa2290 --- /dev/null +++ b/arch/arm/boot/dts/am335x-boneblack-wl1835mod-cape.dtsi @@ -0,0 +1,128 @@ +/* + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +#include + +/ { + wlan_en_reg: fixedregulator@2 { + compatible = "regulator-fixed"; + regulator-name = "wlan-en-regulator"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + + /* WL_EN */ + gpio = <&gpio0 26 0>; + enable-active-high; + }; + + kim { + compatible = "kim"; + nshutdown_gpio = <44>; /* Bank1, pin12 */ + dev_name = "/dev/ttyO4"; + flow_cntrl = <1>; + baud_rate = <3000000>; + }; + + btwilink { + compatible = "btwilink"; + }; +}; + +&am33xx_pinmux { + bt_pins: pinmux_bt_pins { + pinctrl-single,pins = < + 0x30 (PIN_OUTPUT_PULLUP | MUX_MODE7) /* gpmc_ad12.gpio1_12 */ + >; + }; + + mmc2_pins: pinmux_mmc2_pins { + pinctrl-single,pins = < + 0x80 (PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_csn1.mmc1_clk */ + 0x84 (PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_csn2.mmc1_cmd */ + 0x00 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad0.mmc1_dat0 */ + 0x04 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad1.mmc1_dat1 */ + 0x08 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad2.mmc1_dat2 */ + 0x0c (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad3.mmc1_dat3 */ + >; + }; + + mmc2_pins_sleep: pinmux_mmc2_pins_sleep { + pinctrl-single,pins = < + 0x80 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_csn1.mmc1_clk */ + 0x84 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_csn2.mmc1_cmd */ + 0x00 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad0.mmc1_dat0 */ + 0x04 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad1.mmc1_dat1 */ + 0x08 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad2.mmc1_dat2 */ + 0x0c (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad3.mmc1_dat3 */ + >; + }; + + /* wl18xx card enable/irq GPIOs. */ + wlan_pins: pinmux_wlan_pins { + pinctrl-single,pins = < + 0x28 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad10.gpio0_26 WL_EN*/ + 0x2C (PIN_INPUT_PULLUP | MUX_MODE7) /* gpmc_ad11.gpio0_27 WL_IRQ*/ + 0x7C (PIN_OUTPUT_PULLUP | MUX_MODE0) /* gpmc_csn0.gpio1_29 BF_EN*/ + >; + }; + + /* wl18xx card enable/irq GPIOs. */ + wlan_pins_sleep: pinmux_wlan_pins_sleep { + pinctrl-single,pins = < + 0x28 (PIN_OUTPUT_PULLUP | MUX_MODE7) /* gpmc_ad10.gpio0_26 WL_EN*/ + 0x2C (PIN_INPUT_PULLUP | MUX_MODE7) /* gpmc_ad11.gpio0_27 WL_IRQ*/ + 0x7C (PIN_OUTPUT_PULLUP | MUX_MODE0) /* gpmc_csn0.gpio1_29 BF_EN*/ + >; + }; + + uart4_pins_default: pinmux_uart4_pins_default { + pinctrl-single,pins = < + 0xD0 (PIN_INPUT | MUX_MODE6) /* lcd_data12.uart4_cts */ + 0xD4 (PIN_OUTPUT_PULLDOWN | MUX_MODE6) /* lcd_data13.uart4_rts */ + 0x70 (PIN_INPUT_PULLUP | MUX_MODE6) /* gpmc_wait0.uart4_rxd */ + 0x74 (PIN_OUTPUT_PULLDOWN | MUX_MODE6) /* gpmc_wpn.uart4_txd */ + >; + }; + + uart4_pins_sleep: pinmux_uart4_pins_sleep { + pinctrl-single,pins = < + 0xD0 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* lcd_data12.uart4_cts */ + 0xD4 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* lcd_data13.uart4_rts */ + 0x70 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_wait0.uart4_rxd */ + 0x74 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_wpn.uart4_txd */ + >; + }; +}; + +&mmc2 { + status = "okay"; + vmmc-supply = <&wlan_en_reg>; + bus-width = <4>; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&mmc2_pins &wlan_pins>; + pinctrl-1 = <&mmc2_pins_sleep &wlan_pins_sleep>; + ti,non-removable; + ti,needs-special-hs-handling; + cap-power-off-card; + keep-power-in-suspend; + + #address-cells = <1>; + #size-cells = <0>; + wlcore: wlcore@0 { + compatible = "ti,wl1835"; + reg = <2>; + interrupt-parent = <&gpio0>; + interrupts = <27 IRQ_TYPE_LEVEL_HIGH>; + }; +}; + +&uart4 { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&uart4_pins_default>; + pinctrl-1 = <&uart4_pins_sleep>; + status = "okay"; +}; diff --git b/arch/arm/boot/dts/am335x-boneblack-wl1835mod.dts b/arch/arm/boot/dts/am335x-boneblack-wl1835mod.dts new file mode 100644 index 000000000..f35b64abe --- /dev/null +++ b/arch/arm/boot/dts/am335x-boneblack-wl1835mod.dts @@ -0,0 +1,49 @@ +/* + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +/dts-v1/; + +#include "am33xx.dtsi" +#include "am335x-bone-common-no-capemgr.dtsi" + +/ { + model = "TI AM335x BeagleBone Black"; + compatible = "ti,am335x-bone-black", "ti,am335x-bone", "ti,am33xx"; +}; + +&ldo3_reg { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; +}; + +&mmc1 { + vmmc-supply = <&vmmcsd_fixed>; +}; + +/* EMMC in reset */ +&gpio1 { + emmc_rst { + gpio-hog; + gpios = <20 0>; + output-high; + line-name = "EMMC ResetN"; + }; +}; + +&cpu0_opp_table { + /* + * All PG 2.0 silicon may not support 1GHz but some of the early + * BeagleBone Blacks have PG 2.0 silicon which is guaranteed + * to support 1GHz OPP so enable it for PG 2.0 on this board. + */ + oppnitro@1000000000 { + opp-supported-hw = <0x06 0x0100>; + }; +}; + +#include "am335x-boneblack-wl1835mod-cape.dtsi" diff --git a/arch/arm/boot/dts/am335x-boneblack.dts b/arch/arm/boot/dts/am335x-boneblack.dts index 6bbb1fee0..8f5d55994 100644 --- a/arch/arm/boot/dts/am335x-boneblack.dts +++ b/arch/arm/boot/dts/am335x-boneblack.dts @@ -10,6 +10,7 @@ #include "am33xx.dtsi" #include "am335x-bone-common.dtsi" #include +/* #include "am335x-bone-jtag.dtsi" */ / { model = "TI AM335x BeagleBone Black"; @@ -34,6 +35,17 @@ status = "okay"; }; +&cpu0_opp_table { + /* + * All PG 2.0 silicon may not support 1GHz but some of the early + * BeagleBone Blacks have PG 2.0 silicon which is guaranteed + * to support 1GHz OPP so enable it for PG 2.0 on this board. + */ + oppnitro@1000000000 { + opp-supported-hw = <0x06 0x0100>; + }; +}; + &am33xx_pinmux { nxp_hdmi_bonelt_pins: nxp_hdmi_bonelt_pins { pinctrl-single,pins = < @@ -108,10 +120,6 @@ }; }; -&rtc { - system-power-controller; -}; - &mcasp0 { #sound-dai-cells = <0>; pinctrl-names = "default"; diff --git b/arch/arm/boot/dts/am335x-boneblue-wl1835.dtsi b/arch/arm/boot/dts/am335x-boneblue-wl1835.dtsi new file mode 100644 index 000000000..64731b062 --- /dev/null +++ b/arch/arm/boot/dts/am335x-boneblue-wl1835.dtsi @@ -0,0 +1,143 @@ + +#include + +/ { + wlan_en_reg: fixedregulator@2 { + compatible = "regulator-fixed"; + regulator-name = "wlan-en-regulator"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + startup-delay-us= <70000>; + + /* WL_EN */ + gpio = <&gpio3 9 0>; + enable-active-high; + }; + + leds { + pinctrl-names = "default"; + pinctrl-0 = <&wl18xx_pins>; + compatible = "gpio-leds"; + + wl18xx_bt_en { + label = "wl18xx_bt_en"; + gpios = <&gpio0 28 GPIO_ACTIVE_HIGH>; + default-state = "off"; + }; + }; + + btwilink { + compatible = "btwilink"; + }; +}; + +&am33xx_pinmux { + wl18xx_pins: pinmux_wl18xx_pins { + pinctrl-single,pins = < + 0x128 (PIN_OUTPUT_PULLUP | MUX_MODE7) /* (K17) gmii1_txd0.gpio0[28] - BT_EN */ + >; + }; + + wlbtbuf_pin: pinmux_wlbtbuf_pin { + pinctrl-single,pins = < + 0x130 ( PIN_OUTPUT_PULLUP | MUX_MODE7 ) /* (L18) gmii1_rxclk.gpio3[10] - LS_BUF_EN */ + >; + }; + + mmc3_pins: pinmux_mmc3_pins { + pinctrl-single,pins = < + 0x13c ( PIN_INPUT_PULLUP | MUX_MODE6 ) /* (L15) gmii1_rxd1.mmc2_clk */ + 0x114 ( PIN_INPUT_PULLUP | MUX_MODE6 ) /* (J16) gmii1_txen.mmc2_cmd */ + 0x118 ( PIN_INPUT_PULLUP | MUX_MODE5 ) /* (J17) gmii1_rxdv.mmc2_dat0 */ + 0x11c ( PIN_INPUT_PULLUP | MUX_MODE5 ) /* (J18) gmii1_txd3.mmc2_dat1 */ + 0x120 ( PIN_INPUT_PULLUP | MUX_MODE5 ) /* (K15) gmii1_txd2.mmc2_dat2 */ + 0x108 ( PIN_INPUT_PULLUP | MUX_MODE5 ) /* (H16) gmii1_col.mmc2_dat3 */ + >; + }; + + mmc3_pins_sleep: pinmux_mmc3_pins_sleep { + pinctrl-single,pins = < + 0x13c ( PIN_INPUT_PULLDOWN | MUX_MODE6 ) /* (L15) gmii1_rxd1.mmc2_clk */ + 0x114 ( PIN_INPUT_PULLDOWN | MUX_MODE6 ) /* (J16) gmii1_txen.mmc2_cmd */ + 0x118 ( PIN_INPUT_PULLDOWN | MUX_MODE5 ) /* (J17) gmii1_rxdv.mmc2_dat0 */ + 0x11c ( PIN_INPUT_PULLDOWN | MUX_MODE5 ) /* (J18) gmii1_txd3.mmc2_dat1 */ + 0x120 ( PIN_INPUT_PULLDOWN | MUX_MODE5 ) /* (K15) gmii1_txd2.mmc2_dat2 */ + 0x108 ( PIN_INPUT_PULLDOWN | MUX_MODE5 ) /* (H16) gmii1_col.mmc2_dat3 */ + >; + }; + + /* wl18xx card enable/irq GPIOs. */ + wlan_pins: pinmux_wlan_pins { + pinctrl-single,pins = < + 0x12c (PIN_OUTPUT_PULLDOWN | MUX_MODE7 ) /* (K18) gmii1_txclk.gpio3[9] - WL_EN */ + 0x124 (PIN_INPUT_PULLUP | MUX_MODE7 ) /* (K16) gmii1_txd1.gpio0[21] - WL_IRQ */ + >; + }; + + /* wl18xx card enable/irq GPIOs. */ + wlan_pins_sleep: pinmux_wlan_pins_sleep { + pinctrl-single,pins = < + 0x12c (PIN_OUTPUT_PULLDOWN | MUX_MODE7 ) /* (K18) gmii1_txclk.gpio3[9] - WL_EN */ + 0x124 (PIN_INPUT_PULLUP | MUX_MODE7 ) /* (K16) gmii1_txd1.gpio0[21] - WL_IRQ */ + >; + }; + + uart3_pins_default: pinmux_uart3_pins_default { + pinctrl-single,pins = < + 0x134 ( PIN_INPUT_PULLUP | MUX_MODE1 ) /* (L17) gmii1_rxd3.uart3_rxd */ + 0x138 ( PIN_OUTPUT_PULLDOWN | MUX_MODE1 ) /* (L16) gmii1_rxd2.uart3_txd */ + 0x148 ( PIN_INPUT | MUX_MODE3 ) /* (M17) mdio_data.uart3_ctsn */ + 0x14c ( PIN_OUTPUT_PULLDOWN | MUX_MODE3 ) /* (M18) mdio_clk.uart3_rtsn */ + >; + }; + + uart3_pins_sleep: pinmux_uart3_pins_sleep { + pinctrl-single,pins = < + 0x134 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* (L17) gmii1_rxd3.uart3_rxd */ + 0x138 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* (L16) gmii1_rxd2.uart3_txd */ + 0x148 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* (M17) mdio_data.uart3_ctsn */ + 0x14c (PIN_INPUT_PULLDOWN | MUX_MODE7) /* (M18) mdio_clk.uart3_rtsn */ + >; + }; +}; + +&mmc3 { + dmas = <&edma_xbar 12 0 1 + &edma_xbar 13 0 2>; + dma-names = "tx", "rx"; + status = "okay"; + vmmc-supply = <&wlan_en_reg>; + bus-width = <4>; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&mmc3_pins &wlan_pins &wlbtbuf_pin>; + pinctrl-1 = <&mmc3_pins_sleep &wlan_pins_sleep &wlbtbuf_pin>; + ti,non-removable; + ti,needs-special-hs-handling; + cap-power-off-card; + keep-power-in-suspend; + + #address-cells = <1>; + #size-cells = <0>; + wlcore: wlcore@0 { + compatible = "ti,wl1835"; + reg = <2>; + interrupt-parent = <&gpio0>; + interrupts = <21 IRQ_TYPE_EDGE_RISING>; + }; +}; + +&uart3 { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&uart3_pins_default>; + pinctrl-1 = <&uart3_pins_sleep>; + status = "okay"; +}; + +&gpio3 { + ls_buf_en { + gpio-hog; + gpios = <10 GPIO_ACTIVE_HIGH>; + output-high; + line-name = "LS_BUF_EN"; + }; +}; diff --git b/arch/arm/boot/dts/am335x-boneblue.dts b/arch/arm/boot/dts/am335x-boneblue.dts new file mode 100644 index 000000000..e2a2fb54f --- /dev/null +++ b/arch/arm/boot/dts/am335x-boneblue.dts @@ -0,0 +1,569 @@ +/* + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +/dts-v1/; + +#include "am33xx.dtsi" +#include "am335x-bone-common-no-capemgr.dtsi" +#include "am335x-bone-common-universal-pins.dtsi" +#include "am335x-boneblue-wl1835.dtsi" +/* #include "am33xx-pruss-rproc.dtsi" */ + +#define BLUE_IO(x, y) AM33XX_IOPAD((x)*4+0x800, (y)) /* not used anymore */ + + +/ { + model = "TI AM335x BeagleBone Blue"; + compatible = "ti,am335x-bone-blue", "ti,am335x-bone", "ti,am33xx"; +}; + +&ldo3_reg { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; +}; + +&mmc1 { + vmmc-supply = <&vmmcsd_fixed>; +}; + +&mmc2 { + vmmc-supply = <&vmmcsd_fixed>; + pinctrl-names = "default"; + pinctrl-0 = <&emmc_pins>; + bus-width = <8>; + status = "okay"; +}; + +&mac { + status = "disabled"; +}; + +/******************************************************************************* +* Pin Muxing +*******************************************************************************/ +&am33xx_pinmux { + + /*************************************************************************** + * Static Pinmux + ***************************************************************************/ + mux_helper_pins: pins { + pinctrl-single,pins = < + + /* GPIO Inputs */ + 0x09c 0x37 /*P8.9 Pause BUTTON, input pullup*/ + 0x098 0x37 /*P8.10 MODE BUTTON input pullup*/ + 0x1AC 0x37 /*P9.25 MPU-9150 INTERRUPT IN*/ + + /* LEDs GPIO Out*/ + 0x090 0x0F /* P8.7 R7 LED_RED */ + 0x094 0x0F /* P8.8 T7 LED_GREEN */ + 0x02C 0x0F /* P8.17 U12 BATT_LED_1 */ + 0x0DC 0x0F /* P8.32 T5 BATT_LED_2 diff from cape! */ + 0x07c 0x0F /* P8.26 V6 BATT_LED_3 */ + 0x028 0x0F /* P8.14 T11 BATT_LED_4 */ + + /* Motor Control GPIO Out*/ + 0x0a8 0x0F /*P8.43 MDIR_3B*/ + 0x0ac 0x0F /*P8.44 MDIR_3A*/ + 0x0a0 0x0F /*P8.45 MDIR_4A*/ + 0x0a4 0x0F /*P8.46 MDIR_4B*/ + 0x074 0x0F /*P9.13 MDIR_1B*/ + 0x040 0x0F /*P9.15 MDIR_2A*/ + 0x1b4 0x0F /*P9.41 MOT_STBY*/ + 0x088 0x0F /*T13 MDIR_1A different from cape! */ + 0x0D8 0x0F /*P8.31 MDIR_2B different from cape! */ + + /* HRPWM 1 */ + 0x048 0x6 /* P9_14 | MODE 6 */ + 0x04c 0x6 /* P9_16 | MODE 6 */ + + /* HRPWM 2 */ + 0x020 0x4 /* P8_19 | MODE 4 */ + 0x024 0x4 /* P8_13 | MODE 4 */ + + /* EQEP */ + 0x1A0 0x31 /* P9_42,EQEP0A, MODE1 */ + 0x1A4 0x31 /* P9_27,EQEP0B, MODE1 */ + 0x0D4 0x32 /* P8_33,EQEP1B, MODE2 */ + 0x0D0 0x32 /* P8_35,EQEP1A, MODE2 */ + 0x030 0x34 /* P8_12,EQEP2A, MODE4 */ + 0x034 0x34 /* P8_11,EQEP2B, MODE4 */ + + /* PRU encoder input */ + 0x03c 0x36 /* P8_15,PRU0_r31_15,MODE6 */ + 0x038 0x36 /* P8_16,PRU0_r31_16,MODE6 */ + + /* PRU Servo output */ + 0x0e0 0x05 /*pru1_pru_r30_8, MODE5*/ + 0x0e8 0x05 /*pru1_pru_r30_10, MODE5 */ + 0x0e4 0x05 /*pr1_pru1_pru_r30_9, MODE5 */ + 0x0ec 0x05 /*pru1_pru_r30_11, MODE5 */ + 0x0b8 0x05 /*pru1_pru_r30_6, MODE5 */ + 0x0bc 0x05 /*pru1_pru_r30_7, MODE5 */ + 0x0b0 0x05 /*pru1_pru_r30_4, MODE5 */ + 0x0b4 0x05 /*pru1_pru_r30_5, MODE5 */ + 0x0C8 0x0F /*P8.36, SERVO_PWR GPIO OUT*/ + + /* I2C1 */ + 0x15C 0x32 /* P9.17,i2c1_scl,INPUT_PULLUP,MODE2 */ + 0x158 0x32 /* P9.18,i2c1_sda,INPUT_PULLUP,MODE2 */ + + /* I2C2 */ + 0x17c 0x73 /* P9.19, i2c2_sda, mode 3 */ + 0x178 0x73 /* P9.20, i2c2_sda, mode 3 */ + + /* UART5 */ + 0x0C4 0x34 /* P8.38,uart5_rxd,MODE4 */ + 0x0C0 0x14 /* P8.37,uart5_txd,MODE4 */ + + /* WILINK 8 */ + 0x08c 0x0F /*P8.18 V12 A2DP FSYNC */ + 0x078 0x0F /*P9.12 A2DP_CLOCK*/ + + /* DCAN */ + 0x16c ( PIN_INPUT | MUX_MODE2 ) /* (E17) uart0_rtsn.dcan1_rx */ + 0x168 ( PIN_OUTPUT | MUX_MODE2 ) /* (E18) uart0_ctsn.dcan1_tx */ + >; + + /*********************************************************************** + * New configurable pinmux modes for pins not on Black headers + ***********************************************************************/ + /* H18 SPI1_SS1 */ + H18_default_pin: pinmux_H18_default_pin { + pinctrl-single,pins = < 0x144 ( PIN_OUTPUT | MUX_MODE4 ) >; }; + H18_gpio_pin: pinmux_H18_gpio_pin { + pinctrl-single,pins = < 0x144 ( PIN_OUTPUT | MUX_MODE7 ) >; }; + H18_gpio_pu_pin: pinmux_H18_gpio_pu_pin { + pinctrl-single,pins = < 0x144 ( PIN_INPUT_PULLUP | MUX_MODE7 ) >; }; + H18_gpio_pd_pin: pinmux_H18_gpio_pd_pin { + pinctrl-single,pins = < 0x144 ( PIN_INPUT_PULLDOWN | MUX_MODE7 ) >; }; + H18_spi_pin: pinmux_H18_spi_pin { + pinctrl-single,pins = < 0x144 ( PIN_OUTPUT | MUX_MODE2 ) >; }; + + /* C18 SPI1_SS2 */ + C18_default_pin: pinmux_C18_default_pin { + pinctrl-single,pins = < 0x164 ( PIN_OUTPUT | MUX_MODE4 ) >; }; + C18_gpio_pin: pinmux_C18_gpio_pin { + pinctrl-single,pins = < 0x164 ( PIN_OUTPUT | MUX_MODE7 ) >; }; + C18_gpio_pu_pin: pinmux_C18_gpio_pu_pin { + pinctrl-single,pins = < 0x164 ( PIN_INPUT_PULLUP | MUX_MODE7 ) >; }; + C18_gpio_pd_pin: pinmux_C18_gpio_pd_pin { + pinctrl-single,pins = < 0x164 ( PIN_INPUT_PULLDOWN | MUX_MODE7 ) >; }; + C18_spi_pin: pinmux_C18_spi_pin { + pinctrl-single,pins = < 0x164 ( PIN_OUTPUT | MUX_MODE2 ) >; }; + + /* U16 BLUE_GP0_PIN_3 gpio 1_25 */ + U16_default_pin: pinmux_U16_default_pin { + pinctrl-single,pins = < 0x064 ( PIN_INPUT_PULLUP | MUX_MODE7 ) >; }; + U16_gpio_pin: pinmux_U16_gpio_pin { + pinctrl-single,pins = < 0x064 ( PIN_OUTPUT | MUX_MODE7 ) >; }; + U16_gpio_pu_pin: pinmux_U16_gpio_pu_pin { + pinctrl-single,pins = < 0x064 ( PIN_INPUT_PULLUP | MUX_MODE7 ) >; }; + U16_gpio_pd_pin: pinmux_U16_gpio_pd_pin { + pinctrl-single,pins = < 0x064 ( PIN_INPUT_PULLDOWN | MUX_MODE7 ) >; }; + + /* D13 BLUE_GP0_PIN_5 gpio 3_20 */ + D13_default_pin: pinmux_D13_default_pin { + pinctrl-single,pins = < 0x1A8 ( PIN_INPUT_PULLUP | MUX_MODE7 ) >; }; + D13_gpio_pin: pinmux_D13_gpio_pin { + pinctrl-single,pins = < 0x1A8 ( PIN_OUTPUT | MUX_MODE7 ) >; }; + D13_gpio_pu_pin: pinmux_D13_gpio_pu_pin { + pinctrl-single,pins = < 0x1A8 ( PIN_INPUT_PULLUP | MUX_MODE7 ) >; }; + D13_gpio_pd_pin: pinmux_D13_gpio_pd_pin { + pinctrl-single,pins = < 0x1A8 ( PIN_INPUT_PULLDOWN | MUX_MODE7 ) >; }; + + /* J15 BLUE_GP1_PIN_3 gpio 3_2 */ + J15_default_pin: pinmux_J15_default_pin { + pinctrl-single,pins = < 0x110 ( PIN_INPUT_PULLUP | MUX_MODE7 ) >; }; + J15_gpio_pin: pinmux_J15_gpio_pin { + pinctrl-single,pins = < 0x110 ( PIN_OUTPUT | MUX_MODE7 ) >; }; + J15_gpio_pu_pin: pinmux_J15_gpio_pu_pin { + pinctrl-single,pins = < 0x110 ( PIN_INPUT_PULLUP | MUX_MODE7 ) >; }; + J15_gpio_pd_pin: pinmux_J15_gpio_pd_pin { + pinctrl-single,pins = < 0x110 ( PIN_INPUT_PULLDOWN | MUX_MODE7 ) >; }; + + /* H17 BLUE_GP1_PIN_4 gpio 3_1 */ + H17_default_pin: pinmux_H17_default_pin { + pinctrl-single,pins = < 0x10C ( PIN_INPUT_PULLUP | MUX_MODE7 ) >; }; + H17_gpio_pin: pinmux_H17_gpio_pin { + pinctrl-single,pins = < 0x10C ( PIN_OUTPUT | MUX_MODE7 ) >; }; + H17_gpio_pu_pin: pinmux_H17_gpio_pu_pin { + pinctrl-single,pins = < 0x10C ( PIN_INPUT_PULLUP | MUX_MODE7 ) >; }; + H17_gpio_pd_pin: pinmux_H17_gpio_pd_pin { + pinctrl-single,pins = < 0x10C ( PIN_INPUT_PULLDOWN | MUX_MODE7 ) >; }; + }; + +}; + + +/******************************************************************************* +* apply static and dynamic pinmux modes listed above. Pins shared with the black +* header pins get the modes from am335x-boneblack-common-universal-pins.dtsi +*******************************************************************************/ +&ocp { + /* activate the static pinmux helper list of pin modes above */ + test_helper: helper { + compatible = "bone-pinmux-helper"; + pinctrl-names = "default"; + pinctrl-0 = <&mux_helper_pins>; + + status = "okay"; + }; + + /* UART4 RX DSM */ + P9_11_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "uart"; + pinctrl-0 = <&P9_11_default_pin>; + pinctrl-1 = <&P9_11_gpio_pin>; + pinctrl-2 = <&P9_11_gpio_pu_pin>; + pinctrl-3 = <&P9_11_gpio_pd_pin>; + pinctrl-4 = <&P9_11_uart_pin>; + }; + + /* UART 2 TX GPS*/ + P9_21_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "spi", "uart", "i2c", "pwm"; + pinctrl-0 = <&P9_21_default_pin>; + pinctrl-1 = <&P9_21_gpio_pin>; + pinctrl-2 = <&P9_21_gpio_pu_pin>; + pinctrl-3 = <&P9_21_gpio_pd_pin>; + pinctrl-4 = <&P9_21_spi_pin>; + pinctrl-5 = <&P9_21_uart_pin>; + pinctrl-6 = <&P9_21_i2c_pin>; + pinctrl-7 = <&P9_21_pwm_pin>; + }; + + /* UART 2 RX GPS */ + P9_22_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "spi", "uart", "i2c", "pwm"; + pinctrl-0 = <&P9_22_default_pin>; + pinctrl-1 = <&P9_22_gpio_pin>; + pinctrl-2 = <&P9_22_gpio_pu_pin>; + pinctrl-3 = <&P9_22_gpio_pd_pin>; + pinctrl-4 = <&P9_22_spi_pin>; + pinctrl-5 = <&P9_22_uart_pin>; + pinctrl-6 = <&P9_22_i2c_pin>; + pinctrl-7 = <&P9_22_pwm_pin>; + }; + + /* SPI MISO */ + P9_29_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "pwm", "spi", "pruout", "pruin"; + pinctrl-0 = <&P9_29_default_pin>; + pinctrl-1 = <&P9_29_gpio_pin>; + pinctrl-2 = <&P9_29_gpio_pu_pin>; + pinctrl-3 = <&P9_29_gpio_pd_pin>; + pinctrl-4 = <&P9_29_pwm_pin>; + pinctrl-5 = <&P9_29_spi_pin>; + pinctrl-6 = <&P9_29_pruout_pin>; + pinctrl-7 = <&P9_29_pruin_pin>; + }; + + /* SPI MOSI */ + P9_30_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "pwm", "spi", "pruout", "pruin"; + pinctrl-0 = <&P9_30_default_pin>; + pinctrl-1 = <&P9_30_gpio_pin>; + pinctrl-2 = <&P9_30_gpio_pu_pin>; + pinctrl-3 = <&P9_30_gpio_pd_pin>; + pinctrl-4 = <&P9_30_pwm_pin>; + pinctrl-5 = <&P9_30_spi_pin>; + pinctrl-6 = <&P9_30_pruout_pin>; + pinctrl-7 = <&P9_30_pruin_pin>; + }; + + /* SPI SCK */ + P9_31_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "pwm", "spi", "pruout", "pruin"; + pinctrl-0 = <&P9_31_default_pin>; + pinctrl-1 = <&P9_31_gpio_pin>; + pinctrl-2 = <&P9_31_gpio_pu_pin>; + pinctrl-3 = <&P9_31_gpio_pd_pin>; + pinctrl-4 = <&P9_31_pwm_pin>; + pinctrl-5 = <&P9_31_spi_pin>; + pinctrl-6 = <&P9_31_pruout_pin>; + pinctrl-7 = <&P9_31_pruin_pin>; + }; + + /* SPI SS1 */ + H18_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "spi"; + pinctrl-0 = <&H18_default_pin>; + pinctrl-1 = <&H18_gpio_pin>; + pinctrl-2 = <&H18_gpio_pu_pin>; + pinctrl-3 = <&H18_gpio_pd_pin>; + pinctrl-4 = <&H18_spi_pin>; + }; + + /* SPI SS2 */ + C18_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "spi"; + pinctrl-0 = <&C18_default_pin>; + pinctrl-1 = <&C18_gpio_pin>; + pinctrl-2 = <&C18_gpio_pu_pin>; + pinctrl-3 = <&C18_gpio_pd_pin>; + pinctrl-4 = <&C18_spi_pin>; + }; + + /* UART 1 TX */ + P9_24_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "uart", "can", "i2c", "pruin"; + pinctrl-0 = <&P9_24_default_pin>; + pinctrl-1 = <&P9_24_gpio_pin>; + pinctrl-2 = <&P9_24_gpio_pu_pin>; + pinctrl-3 = <&P9_24_gpio_pd_pin>; + pinctrl-4 = <&P9_24_uart_pin>; + pinctrl-5 = <&P9_24_can_pin>; + pinctrl-6 = <&P9_24_i2c_pin>; + pinctrl-7 = <&P9_24_pruin_pin>; + }; + + /* UART 1 RX */ + P9_26_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "uart", "can", "i2c", "pruin"; + pinctrl-0 = <&P9_26_default_pin>; + pinctrl-1 = <&P9_26_gpio_pin>; + pinctrl-2 = <&P9_26_gpio_pu_pin>; + pinctrl-3 = <&P9_26_gpio_pd_pin>; + pinctrl-4 = <&P9_26_uart_pin>; + pinctrl-5 = <&P9_26_can_pin>; + pinctrl-6 = <&P9_26_i2c_pin>; + pinctrl-7 = <&P9_26_pruin_pin>; + }; + + /* U16 BLUE_GP0_PIN_3 gpio 1_25*/ + U16_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd"; + pinctrl-0 = <&U16_default_pin>; + pinctrl-1 = <&U16_gpio_pin>; + pinctrl-2 = <&U16_gpio_pu_pin>; + pinctrl-3 = <&U16_gpio_pd_pin>; + }; + + + /* BLUE_GP0_PIN_3 gpio1_17*/ + P9_23_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "pwm"; + pinctrl-0 = <&P9_23_default_pin>; + pinctrl-1 = <&P9_23_gpio_pin>; + pinctrl-2 = <&P9_23_gpio_pu_pin>; + pinctrl-3 = <&P9_23_gpio_pd_pin>; + pinctrl-4 = <&P9_23_pwm_pin>; + }; + + /* BLUE_GP0_PIN_5 gpio3_20 */ + D13_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd"; + pinctrl-0 = <&D13_default_pin>; + pinctrl-1 = <&D13_gpio_pin>; + pinctrl-2 = <&D13_gpio_pu_pin>; + pinctrl-3 = <&D13_gpio_pd_pin>; + }; + + /* BLUE_GP0_PIN_6 gpio3_17 */ + P9_28_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "pwm", "spi", "pwm2", "pruout", "pruin"; + pinctrl-0 = <&P9_28_default_pin>; + pinctrl-1 = <&P9_28_gpio_pin>; + pinctrl-2 = <&P9_28_gpio_pu_pin>; + pinctrl-3 = <&P9_28_gpio_pd_pin>; + pinctrl-4 = <&P9_28_pwm_pin>; + pinctrl-5 = <&P9_28_spi_pin>; + pinctrl-6 = <&P9_28_pwm2_pin>; + pinctrl-7 = <&P9_28_pruout_pin>; + pinctrl-8 = <&P9_28_pruin_pin>; + }; + + /* BLUE_GP1_PIN_3 gpio3_2 */ + J15_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd"; + pinctrl-0 = <&J15_default_pin>; + pinctrl-1 = <&J15_gpio_pin>; + pinctrl-2 = <&J15_gpio_pu_pin>; + pinctrl-3 = <&J15_gpio_pd_pin>; + }; + + /* BLUE_GP1_PIN_4 gpio3_1 */ + H17_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd"; + pinctrl-0 = <&H17_default_pin>; + pinctrl-1 = <&H17_gpio_pin>; + pinctrl-2 = <&H17_gpio_pu_pin>; + pinctrl-3 = <&H17_gpio_pd_pin>; + }; + + + +}; + + +/******************************************************************************* +* PWMSS +*******************************************************************************/ +&epwmss0 { + status = "okay"; +}; + +&epwmss1 { + status = "okay"; +}; + +&epwmss2 { + status = "okay"; +}; + +&ehrpwm0 { + status = "okay"; +}; + +&ehrpwm1 { + status = "okay"; +}; + +&ehrpwm2 { + status = "okay"; +}; + + +/******************************************************************************* +* EQEP +*******************************************************************************/ +&eqep0 { + count_mode = <0>; /* 0 - Quadrature mode, normal 90 phase offset cha & chb. 1 - Direction mode. cha input = clock, chb input = direction */ + swap_inputs = <0>; /* Are channel A and channel B swapped? (0 - no, 1 - yes) */ + invert_qa = <1>; /* Should we invert the channel A input? */ + invert_qb = <1>; /* Should we invert the channel B input? I invert these because my encoder outputs drive transistors that pull down the pins */ + invert_qi = <0>; /* Should we invert the index input? */ + invert_qs = <0>; /* Should we invert the strobe input? */ + status = "okay"; +}; + +&eqep1 { + count_mode = <0>; /* 0 - Quadrature mode, normal 90 phase offset cha & chb. 1 - Direction mode. cha input = clock, chb input = direction */ + swap_inputs = <0>; /* Are channel A and channel B swapped? (0 - no, 1 - yes) */ + invert_qa = <1>; /* Should we invert the channel A input? */ + invert_qb = <1>; /* Should we invert the channel B input? I invert these because my encoder outputs drive transistors that pull down the pins */ + invert_qi = <0>; /* Should we invert the index input? */ + invert_qs = <0>; /* Should we invert the strobe input? */ + status = "okay"; +}; + +&eqep2 { + count_mode = <0>; /* 0 - Quadrature mode, normal 90 phase offset cha & chb. 1 - Direction mode. cha input = clock, chb input = direction */ + swap_inputs = <0>; /* Are channel A and channel B swapped? (0 - no, 1 - yes) */ + invert_qa = <1>; /* Should we invert the channel A input? */ + invert_qb = <1>; /* Should we invert the channel B input? I invert these because my encoder outputs drive transistors that pull down the pins */ + invert_qi = <0>; /* Should we invert the index input? */ + invert_qs = <0>; /* Should we invert the strobe input? */ + status = "okay"; +}; + + +/******************************************************************************* + UART +*******************************************************************************/ + +&uart1 { + status = "okay"; +}; + +&uart2 { + status = "okay"; +}; + +&uart4 { + status = "okay"; +}; + +&uart5 { + status = "okay"; +}; + + +/******************************************************************************* + PRU +*******************************************************************************/ +&pruss { + status = "okay"; +}; + + +/******************************************************************************* + I2C +*******************************************************************************/ +&i2c1 { + #address-cells = <1>; + #size-cells = <0>; + status = "okay"; + clock-frequency = <400000>; +}; + +&i2c2 { + #address-cells = <1>; + #size-cells = <0>; + status = "okay"; + clock-frequency = <400000>; +}; + +/******************************************************************************* + SPI +*******************************************************************************/ +&spi1 { + #address-cells = <1>; + #size-cells = <0>; + status = "okay"; + + channel@0 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "spidev"; + reg = <0>; + spi-max-frequency = <24000000>; + }; + + channel@1 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "spidev"; + reg = <1>; + spi-max-frequency = <24000000>; + }; +}; diff --git b/arch/arm/boot/dts/am335x-bonegreen-overlay.dts b/arch/arm/boot/dts/am335x-bonegreen-overlay.dts new file mode 100644 index 000000000..a703fcdfd --- /dev/null +++ b/arch/arm/boot/dts/am335x-bonegreen-overlay.dts @@ -0,0 +1,36 @@ +/* + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +/dts-v1/; + +#include "am33xx.dtsi" +#include "am335x-bone-common.dtsi" + +/ { + model = "TI AM335x BeagleBone Green"; + compatible = "ti,am335x-bone-green", "ti,am335x-bone-black", "ti,am335x-bone", "ti,am33xx"; +}; + +&ldo3_reg { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; +}; + +&mmc1 { + vmmc-supply = <&vmmcsd_fixed>; +}; + +/* EMMC in reset */ +&gpio1 { + emmc_rst { + gpio-hog; + gpios = <20 0>; + output-high; + line-name = "EMMC ResetN"; + }; +}; diff --git b/arch/arm/boot/dts/am335x-bonegreen-wireless.dts b/arch/arm/boot/dts/am335x-bonegreen-wireless.dts new file mode 100644 index 000000000..f37f39e18 --- /dev/null +++ b/arch/arm/boot/dts/am335x-bonegreen-wireless.dts @@ -0,0 +1,48 @@ +/* + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +/dts-v1/; + +#include "am33xx.dtsi" +#include "am335x-bone-common.dtsi" +#include "am335x-bonegreen-wl1835.dtsi" +/* #include "am335x-bone-jtag.dtsi" */ + +/ { + model = "TI AM335x BeagleBone Green Wireless"; + compatible = "ti,am335x-bone-green", "ti,am335x-bone-black", "ti,am335x-bone", "ti,am33xx"; +}; + +&ldo3_reg { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; +}; + +&mmc1 { + vmmc-supply = <&vmmcsd_fixed>; +}; + +&mmc2 { + vmmc-supply = <&vmmcsd_fixed>; + pinctrl-names = "default"; + pinctrl-0 = <&emmc_pins>; + bus-width = <8>; + status = "okay"; +}; + +&uart3 { + status = "okay"; +}; + +&mmc3 { + status = "okay"; +}; + +&mac { + status = "disabled"; +}; diff --git b/arch/arm/boot/dts/am335x-bonegreen-wl1835.dtsi b/arch/arm/boot/dts/am335x-bonegreen-wl1835.dtsi new file mode 100644 index 000000000..0d4798dfa --- /dev/null +++ b/arch/arm/boot/dts/am335x-bonegreen-wl1835.dtsi @@ -0,0 +1,147 @@ +#include + +/ { + wlan_en_reg: fixedregulator@2 { + compatible = "regulator-fixed"; + regulator-name = "wlan-en-regulator"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + startup-delay-us= <70000>; + + /* WL_EN */ + gpio = <&gpio0 26 0>; + enable-active-high; + }; + + btwilink { + compatible = "btwilink"; + }; + + wilink8_pcm: wilink8_pcm { + compatible = "ti,wilink8_bt"; + status = "okay"; + }; + + sound{ + compatible = "ti,wilink8-bt-audio"; + ti,model = "WILINK8_BT"; + ti,audio-codec = <&wilink8_pcm>; + ti,mcasp-controller = <&mcasp0>; + ti,codec-clock-rate = <24000000>; + }; +}; + +&am33xx_pinmux { + bt_pins: pinmux_bt_pins { + pinctrl-single,pins = < + 0x78 (PIN_OUTPUT | MUX_MODE7) /* gpmc_ad12.gpio1_28 BT_EN*/ + >; + }; + + mmc3_pins: pinmux_mmc3_pins { + pinctrl-single,pins = < + 0x8c ( PIN_INPUT_PULLUP | MUX_MODE3 ) /* gpio2_1 gpmc_clk.mmc2_clk */ + 0x88 ( PIN_INPUT_PULLUP | MUX_MODE3) /* gpio2_0 gpmc_csn3.mmc2_cmd */ + 0x30 ( PIN_INPUT_PULLUP | MUX_MODE3 ) /* gpio1_12 gpmc_ad12.mmc2_dat0 */ + 0x34 ( PIN_INPUT_PULLUP | MUX_MODE3 ) /* gpio1_13 gpmc_ad13.mmc2_dat1 */ + 0x38 ( PIN_INPUT_PULLUP | MUX_MODE3 ) /* gpio1_14 gpmc_ad14.mmc2_dat2 */ + 0x3c ( PIN_INPUT_PULLUP | MUX_MODE3 ) /* gpio1_15 gpmc_ad15.mmc2_dat3 */ + >; + }; + + mmc3_pins_sleep: pinmux_mmc3_pins_sleep { + pinctrl-single,pins = < + 0x8c (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpio2_1 gpmc_clk.mmc2_clk */ + 0x88 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpio2_0 gpmc_csn3.mmc2_cmd */ + 0x30 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpio1_12 gpmc_ad12.mmc2_dat0 */ + 0x34 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpio1_13 gpmc_ad13.mmc2_dat1 */ + 0x38 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpio1_14 gpmc_ad14.mmc2_dat2 */ + 0x3c (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpio1_15 gpmc_ad15.mmc2_dat3 */ + >; + }; + + /* wl18xx card enable/irq GPIOs. */ + wlan_pins: pinmux_wlan_pins { + pinctrl-single,pins = < + 0x28 (PIN_OUTPUT_PULLDOWN| MUX_MODE7) /* gpmc_ad10.gpio0_26 WL_EN*/ + 0x2C (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad11.gpio0_27 WL_IRQ*/ + 0x7C (PIN_OUTPUT_PULLUP | MUX_MODE0) /* gpmc_csn0.gpio1_29 Cape_Buffer_EN*/ + >; + }; + + /* wl18xx card enable/irq GPIOs. */ + wlan_pins_sleep: pinmux_wlan_pins_sleep { + pinctrl-single,pins = < + 0x28 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad10.gpio0_26 WL_EN*/ + 0x2C (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad11.gpio0_27 WL_IRQ*/ + 0x7C (PIN_OUTPUT_PULLUP | MUX_MODE0) /* gpmc_csn0.gpio1_29 Cape_Buffer_EN*/ + >; + }; + + uart3_pins_default: pinmux_uart3_pins_default { + pinctrl-single,pins = < + 0x134 ( PIN_INPUT_PULLUP | MUX_MODE1 ) /* (L17) gmii1_rxd3.uart3_rxd */ + 0x138 ( PIN_OUTPUT_PULLDOWN | MUX_MODE1 ) /* (L16) gmii1_rxd2.uart3_txd */ + 0x148 ( PIN_INPUT | MUX_MODE3 ) /* (M17) mdio_data.uart3_ctsn */ + 0x14c ( PIN_OUTPUT_PULLDOWN | MUX_MODE3 ) /* (M18) mdio_clk.uart3_rtsn */ + >; + }; + + uart3_pins_sleep: pinmux_uart3_pins_sleep { + pinctrl-single,pins = < + 0x134 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* (L17) gmii1_rxd3.uart3_rxd */ + 0x138 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* (L16) gmii1_rxd2.uart3_txd */ + 0x148 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* (M17) mdio_data.uart3_ctsn */ + 0x14c (PIN_INPUT_PULLDOWN | MUX_MODE7) /* (M18) mdio_clk.uart3_rtsn */ + >; + }; +}; + +&mmc3 { + dmas = <&edma_xbar 12 0 1 + &edma_xbar 13 0 2>; + dma-names = "tx", "rx"; + status = "okay"; + vmmc-supply = <&wlan_en_reg>; + bus-width = <4>; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&mmc3_pins &wlan_pins>; + pinctrl-1 = <&mmc3_pins_sleep &wlan_pins_sleep>; + ti,non-removable; + ti,needs-special-hs-handling; + cap-power-off-card; + keep-power-in-suspend; + + #address-cells = <1>; + #size-cells = <0>; + wlcore: wlcore@0 { + compatible = "ti,wl1835"; + reg = <2>; + interrupt-parent = <&gpio0>; + interrupts = <27 IRQ_TYPE_EDGE_RISING>; + }; +}; + +&uart3 { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&uart3_pins_default &bt_pins>; + pinctrl-1 = <&uart3_pins_sleep &bt_pins>; + status = "okay"; +}; + +/* BT_AUD_OUT from wl1835 has to be pulled low when WL_EN is activated. */ +/* in case it isn't, wilink8 ends up in one of the test modes that */ +/* intruces various issues (elp wkaeup timeouts etc.) */ +/* On the BBGW this pin is routed through the level shifter (U21) that */ +/* introduces a pullup on the line and wilink8 ends up in a bad state. */ +/* use a gpio hog to force this pin low. An alternative may be adding */ +/* an external pulldown on U21 pin 4. */ + +&gpio3 { + bt_aud_in { + gpio-hog; + gpios = <16 GPIO_ACTIVE_HIGH>; + output-low; + line-name = "MCASP0_AXR0"; + }; +}; diff --git a/arch/arm/boot/dts/am335x-bonegreen.dts b/arch/arm/boot/dts/am335x-bonegreen.dts index dce3c8657..647d4bfca 100644 --- a/arch/arm/boot/dts/am335x-bonegreen.dts +++ b/arch/arm/boot/dts/am335x-bonegreen.dts @@ -9,6 +9,7 @@ #include "am33xx.dtsi" #include "am335x-bone-common.dtsi" +/* #include "am335x-bone-jtag.dtsi" */ / { model = "TI AM335x BeagleBone Green"; @@ -32,22 +33,3 @@ bus-width = <8>; status = "okay"; }; - -&am33xx_pinmux { - uart2_pins: uart2_pins { - pinctrl-single,pins = < - AM33XX_IOPAD(0x950, PIN_INPUT | MUX_MODE1) /* spi0_sclk.uart2_rxd */ - AM33XX_IOPAD(0x954, PIN_OUTPUT | MUX_MODE1) /* spi0_d0.uart2_txd */ - >; - }; -}; - -&uart2 { - pinctrl-names = "default"; - pinctrl-0 = <&uart2_pins>; - status = "okay"; -}; - -&rtc { - system-power-controller; -}; diff --git b/arch/arm/boot/dts/am335x-cape-bbb-exp-c.dtsi b/arch/arm/boot/dts/am335x-cape-bbb-exp-c.dtsi new file mode 100644 index 000000000..01f9cde64 --- /dev/null +++ b/arch/arm/boot/dts/am335x-cape-bbb-exp-c.dtsi @@ -0,0 +1,224 @@ +/* + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include + +#include "am335x-peripheral-can0.dtsi" +#include "am335x-bone-pinmux-can0.dtsi" + +#include "am335x-peripheral-ttyS1.dtsi" +#include "am335x-bone-pinmux-ttyS1.dtsi" + +#include "am335x-peripheral-ttyS2.dtsi" +#include "am335x-bone-pinmux-ttyS2.dtsi" + +#include "am335x-peripheral-ttyS4.dtsi" +#include "am335x-bone-pinmux-ttyS4.dtsi" + +&am33xx_pinmux { + user_leds_s1: user_leds_s1 { + pinctrl-single,pins = < + 0x98 0x7 /* gpmc_wen.gpio2_4, OUTPUT | MODE7 */ + 0x9c 0x7 /* gpmc_ben0_cle.gpio2_5, OUTPUT | MODE7 */ + >; + }; + + bb_lcd_pwm_backlight_pins: pinmux_bb_lcd_pwm_backlight_pins { + pinctrl-single,pins = < + BONE_P9_14 (PIN_OUTPUT_PULLDOWN | MUX_MODE6) /* gpmc_a2.ehrpwm1a */ + >; + }; + + keymap3_pins: pinmux_keymap3_pins { + pinctrl-single,pins = < + 0x040 0x2f /* KEY_UP gpmc_a0.gpio1_16, INPUT | PULLDIS | MODE7 */ + 0x04c 0x2f /* KEY_DOWN gpmc_a3.gpio1_19, INPUT | PULLDIS | MODE7 */ + 0x078 0x2f /* KEY_RIGHT gpmc_ben1.gpio1_28, INPUT | PULLDIS | MODE7 */ + 0x164 0x2f /* KEY_LEFT ecap0_in_pwm0_out.gpio0_7, INPUT | PULLDIS | MODE7 */ + 0x1a4 0x2f /* KEY_ENTER mcasp0_fxr.gpio3_19, INPUT | PULLDIS | MODE7 */ + >; + }; + + edt_ft5306_ts_pins: pinmux_edt_ft5306_ts_pins { + pinctrl-single,pins = < + /* CAP_TSC gpmc_a1.gpio1_17, INPUT | MODE7 */ + BONE_P9_23 (PIN_INPUT_PULLDOWN | MUX_MODE7) + >; + }; + + i2c1_pins: pinmux_i2c1_pins { + pinctrl-single,pins = < + /* spi0_d1.i2c1_sda, SLEWCTRL_SLOW | INPUT_PULLUP | MODE2 */ + BONE_P9_18 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE2) + /* spi0_cs0.i2c1_scl, SLEWCTRL_SLOW | INPUT_PULLUP | MODE2 */ + BONE_P9_17 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE2) + >; + }; + + mcasp0_pins: pinmux_mcasp0_pins { + pinctrl-single,pins = < + 0x190 0x20 /* mcasp0_aclkx.mcasp0_aclkx, INPUT | MODE0 */ + 0x194 0x20 /* mcasp0_fsx.mcasp0_fsx, INPUT | MODE0 */ + 0x198 0x20 /* mcasp0_axr0.mcasp0_axr0, INPUT | MODE0 */ + 0x19c 0x22 /* mcasp0_ahclkr.mcasp0_axr2, INPUT | MODE2 */ + >; + }; +}; + +&epwmss1 { + status = "okay"; +}; + + +&ehrpwm1 { + pinctrl-names = "default"; + pinctrl-0 = <&bb_lcd_pwm_backlight_pins>; + status = "okay"; +}; + +&i2c1 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&i2c1_pins>; + clock-frequency = <400000>; + + edt-ft5306@38 { + status = "okay"; + compatible = "edt,edt-ft5306", "edt,edt-ft5x06"; + pinctrl-names = "default"; + pinctrl-0 = <&edt_ft5306_ts_pins>; + + reg = <0x38>; + interrupt-parent = <&gpio1>; + interrupts = <17 0>; + + touchscreen-size-x = <1024>; + touchscreen-size-y = <600>; + }; + + tlv320aic3x: tlv320aic3x@1b { + compatible = "ti,tlv320aic3x"; + reg = <0x1b>; + status = "okay"; + }; +}; + +&mcasp0 { + pinctrl-names = "default"; + pinctrl-0 = <&mcasp0_pins>; + + status = "okay"; + + op-mode = <0>; /* MCASP_IIS_MODE */ + tdm-slots = <2>; + num-serializer = <16>; + serial-dir = < /* 0: INACTIVE, 1: TX, 2: RX */ + 1 0 2 0 + 0 0 0 0 + 0 0 0 0 + 0 0 0 0 + >; + tx-num-evt = <1>; + rx-num-evt = <1>; +}; + +/ { + backlight { + status = "okay"; + compatible = "pwm-backlight"; + pwms = <&ehrpwm1 0 50000 0>; + brightness-levels = <0 51 53 56 62 75 101 152 255>; + default-brightness-level = <8>; + }; + + gpio_keys { + compatible = "gpio-keys"; + pinctrl-names = "default"; + pinctrl-0 = <&keymap3_pins>; + + #address-cells = <1>; + #size-cells = <0>; + + button@1 { + debounce_interval = <50>; + linux,code = <105>; + label = "left"; + gpios = <&gpio0 7 0x1>; + gpio-key,wakeup; + autorepeat; + }; + button@2 { + debounce_interval = <50>; + linux,code = <106>; + label = "right"; + gpios = <&gpio1 28 0x1>; + gpio-key,wakeup; + autorepeat; + }; + button@3 { + debounce_interval = <50>; + linux,code = <103>; + label = "up"; + gpios = <&gpio1 16 0x1>; + gpio-key,wakeup; + autorepeat; + }; + button@4 { + debounce_interval = <50>; + linux,code = <108>; + label = "down"; + gpios = <&gpio1 19 0x1>; + gpio-key,wakeup; + autorepeat; + }; + button@5 { + debounce_interval = <50>; + linux,code = <28>; + label = "enter"; + gpios = <&gpio3 19 0x1>; + gpio-key,wakeup; + }; + }; + + gpio-leds-cape-lcd { + compatible = "gpio-leds"; + pinctrl-names = "default"; + + pinctrl-0 = <&user_leds_s1>; + + lcd-led0 { + label = "lcd:green:usr0"; + gpios = <&gpio2 4 0>; + linux,default-trigger = "heartbeat"; + default-state = "off"; + }; + + lcd-led1 { + label = "lcd:green:usr1"; + gpios = <&gpio2 5 0>; + linux,default-trigger = "mmc0"; + default-state = "off"; + }; + }; + + sound { + compatible = "ti,da830-evm-audio"; + ti,model = "DA830 EVM"; + ti,audio-codec = <&tlv320aic3x>; + ti,mcasp-controller = <&mcasp0>; + ti,codec-clock-rate = <12000000>; + ti,audio-routing = + "Headphone Jack", "HPLOUT", + "Headphone Jack", "HPROUT", + "MIC3L", "Mic Jack", + "MIC3R", "Mic Jack"; + }; +}; + +#include "am335x-peripheral-panel-1024x600-24bit.dtsi" +#include "am335x-bone-pinmux-panel-1024x600-24bit.dtsi" diff --git b/arch/arm/boot/dts/am335x-cape-bbb-exp-r.dtsi b/arch/arm/boot/dts/am335x-cape-bbb-exp-r.dtsi new file mode 100644 index 000000000..539409c9f --- /dev/null +++ b/arch/arm/boot/dts/am335x-cape-bbb-exp-r.dtsi @@ -0,0 +1,217 @@ +/* + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include + +#include "am335x-peripheral-can0.dtsi" +#include "am335x-bone-pinmux-can0.dtsi" + +#include "am335x-peripheral-ttyS1.dtsi" +#include "am335x-bone-pinmux-ttyS1.dtsi" + +#include "am335x-peripheral-ttyS2.dtsi" +#include "am335x-bone-pinmux-ttyS2.dtsi" + +#include "am335x-peripheral-ttyS4.dtsi" +#include "am335x-bone-pinmux-ttyS4.dtsi" + +&am33xx_pinmux { + user_leds_s1: user_leds_s1 { + pinctrl-single,pins = < + 0x98 0x7 /* gpmc_wen.gpio2_4, OUTPUT | MODE7 */ + 0x9c 0x7 /* gpmc_ben0_cle.gpio2_5, OUTPUT | MODE7 */ + >; + }; + + bb_lcd_pwm_backlight_pins: pinmux_bb_lcd_pwm_backlight_pins { + pinctrl-single,pins = < + BONE_P9_14 (PIN_OUTPUT_PULLDOWN | MUX_MODE6) /* gpmc_a2.ehrpwm1a */ + >; + }; + + keymap3_pins: pinmux_keymap3_pins { + pinctrl-single,pins = < + 0x040 0x2f /* KEY_UP gpmc_a0.gpio1_16, INPUT | PULLDIS | MODE7 */ + 0x04c 0x2f /* KEY_DOWN gpmc_a3.gpio1_19, INPUT | PULLDIS | MODE7 */ + 0x078 0x2f /* KEY_RIGHT gpmc_ben1.gpio1_28, INPUT | PULLDIS | MODE7 */ + 0x164 0x2f /* KEY_LEFT ecap0_in_pwm0_out.gpio0_7, INPUT | PULLDIS | MODE7 */ + 0x1a4 0x2f /* KEY_ENTER mcasp0_fxr.gpio3_19, INPUT | PULLDIS | MODE7 */ + >; + }; + + i2c1_pins: pinmux_i2c1_pins { + pinctrl-single,pins = < + /* spi0_d1.i2c1_sda, SLEWCTRL_SLOW | INPUT_PULLUP | MODE2 */ + BONE_P9_18 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE2) + /* spi0_cs0.i2c1_scl, SLEWCTRL_SLOW | INPUT_PULLUP | MODE2 */ + BONE_P9_17 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE2) + >; + }; + + mcasp0_pins: pinmux_mcasp0_pins { + pinctrl-single,pins = < + 0x190 0x20 /* mcasp0_aclkx.mcasp0_aclkx, INPUT | MODE0 */ + 0x194 0x20 /* mcasp0_fsx.mcasp0_fsx, INPUT | MODE0 */ + 0x198 0x20 /* mcasp0_axr0.mcasp0_axr0, INPUT | MODE0 */ + 0x19c 0x22 /* mcasp0_ahclkr.mcasp0_axr2, INPUT | MODE2 */ + >; + }; +}; + +&epwmss1 { + status = "okay"; +}; + + +&ehrpwm1 { + pinctrl-names = "default"; + pinctrl-0 = <&bb_lcd_pwm_backlight_pins>; + status = "okay"; +}; + +&i2c1 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&i2c1_pins>; + clock-frequency = <400000>; + + tlv320aic3x: tlv320aic3x@1b { + compatible = "ti,tlv320aic3x"; + reg = <0x1b>; + status = "okay"; + }; +}; + +&mcasp0 { + pinctrl-names = "default"; + pinctrl-0 = <&mcasp0_pins>; + + status = "okay"; + + op-mode = <0>; /* MCASP_IIS_MODE */ + tdm-slots = <2>; + num-serializer = <16>; + serial-dir = < /* 0: INACTIVE, 1: TX, 2: RX */ + 1 0 2 0 + 0 0 0 0 + 0 0 0 0 + 0 0 0 0 + >; + tx-num-evt = <1>; + rx-num-evt = <1>; +}; + +&tscadc { + status = "okay"; + tsc { + ti,wires = <4>; + ti,x-plate-resistance = <200>; + ti,coordinate-readouts = <5>; + ti,wire-config = <0x00 0x11 0x22 0x33>; + }; + + adc { + ti,adc-channels = <4 5 6 7>; + }; +}; + +/ { + backlight { + status = "okay"; + compatible = "pwm-backlight"; + pwms = <&ehrpwm1 0 50000 0>; + brightness-levels = <0 51 53 56 62 75 101 152 255>; + default-brightness-level = <8>; + }; + + gpio_keys { + compatible = "gpio-keys"; + pinctrl-names = "default"; + pinctrl-0 = <&keymap3_pins>; + + #address-cells = <1>; + #size-cells = <0>; + + button@1 { + debounce_interval = <50>; + linux,code = <105>; + label = "left"; + gpios = <&gpio0 7 0x1>; + gpio-key,wakeup; + autorepeat; + }; + button@2 { + debounce_interval = <50>; + linux,code = <106>; + label = "right"; + gpios = <&gpio1 28 0x1>; + gpio-key,wakeup; + autorepeat; + }; + button@3 { + debounce_interval = <50>; + linux,code = <103>; + label = "up"; + gpios = <&gpio1 16 0x1>; + gpio-key,wakeup; + autorepeat; + }; + button@4 { + debounce_interval = <50>; + linux,code = <108>; + label = "down"; + gpios = <&gpio1 19 0x1>; + gpio-key,wakeup; + autorepeat; + }; + button@5 { + debounce_interval = <50>; + linux,code = <28>; + label = "enter"; + gpios = <&gpio3 19 0x1>; + gpio-key,wakeup; + }; + }; + + gpio-leds-cape-lcd { + compatible = "gpio-leds"; + pinctrl-names = "default"; + + pinctrl-0 = <&user_leds_s1>; + + lcd-led0 { + label = "lcd:green:usr0"; + gpios = <&gpio2 4 0>; + linux,default-trigger = "heartbeat"; + default-state = "off"; + }; + + lcd-led1 { + label = "lcd:green:usr1"; + gpios = <&gpio2 5 0>; + linux,default-trigger = "mmc0"; + default-state = "off"; + }; + }; + + sound { + compatible = "ti,da830-evm-audio"; + ti,model = "DA830 EVM"; + ti,audio-codec = <&tlv320aic3x>; + ti,mcasp-controller = <&mcasp0>; + ti,codec-clock-rate = <12000000>; + ti,audio-routing = + "Headphone Jack", "HPLOUT", + "Headphone Jack", "HPROUT", + "MIC3L", "Mic Jack", + "MIC3R", "Mic Jack"; + }; +}; + +#include "am335x-peripheral-panel-1024x600-24bit.dtsi" +#include "am335x-bone-pinmux-panel-1024x600-24bit.dtsi" diff --git b/arch/arm/boot/dts/am335x-cape-rtc-ds1307.dtsi b/arch/arm/boot/dts/am335x-cape-rtc-ds1307.dtsi new file mode 100644 index 000000000..bce6ac50c --- /dev/null +++ b/arch/arm/boot/dts/am335x-cape-rtc-ds1307.dtsi @@ -0,0 +1,31 @@ +/* + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include + +&am33xx_pinmux { + i2c2_pins: pinmux_i2c2_pins { + pinctrl-single,pins = < + BONE_P9_20 0x73 /* (SLEWCTRL_SLOW | PIN_INPUT_PULLUP | MUX_MODE3) uart1_ctsn.i2c2_sda */ + BONE_P9_19 0x73 /* (SLEWCTRL_SLOW | PIN_INPUT_PULLUP | MUX_MODE3) uart1_rtsn.i2c2_scl */ + >; + }; +}; + +&i2c2 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c2_pins>; + + status = "okay"; + clock-frequency = <100000>; + + rtc@68 { + compatible = "maxim,ds1307"; + reg = <0x68>; + }; +}; diff --git b/arch/arm/boot/dts/am335x-olimex-som.dts b/arch/arm/boot/dts/am335x-olimex-som.dts new file mode 100644 index 000000000..2b00ad283 --- /dev/null +++ b/arch/arm/boot/dts/am335x-olimex-som.dts @@ -0,0 +1,189 @@ +/* + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +/dts-v1/; + +#include "am33xx.dtsi" +#include "am335x-som-common.dtsi" + +/ { + model = "Olimex AM335x SOM"; + compatible = "olimex,am335x-olimex-som", "ti,am33xx"; +}; + +&ldo3_reg { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; +}; + +&mmc1 { + vmmc-supply = <&vmmcsd_fixed>; +}; + +&am33xx_pinmux { + lcd_pins_default: lcd_pins_default { + pinctrl-single,pins = < + 0x20 0x01 /* gpmc_ad8.lcd_data16, OUTPUT | MODE1 */ + 0x24 0x01 /* gpmc_ad9.lcd_data17, OUTPUT | MODE1 */ + 0x28 0x01 /* gpmc_ad10.lcd_data18, OUTPUT | MODE1 */ + 0x2c 0x01 /* gpmc_ad11.lcd_data19, OUTPUT | MODE1 */ + 0x30 0x01 /* gpmc_ad12.lcd_data20, OUTPUT | MODE1 */ + 0x34 0x01 /* gpmc_ad13.lcd_data21, OUTPUT | MODE1 */ + 0x38 0x01 /* gpmc_ad14.lcd_data22, OUTPUT | MODE1 */ + 0x3c 0x01 /* gpmc_ad15.lcd_data23, OUTPUT | MODE1 */ + 0xa0 0x00 /* lcd_data0.lcd_data0, OUTPUT | MODE0 */ + 0xa4 0x00 /* lcd_data1.lcd_data1, OUTPUT | MODE0 */ + 0xa8 0x00 /* lcd_data2.lcd_data2, OUTPUT | MODE0 */ + 0xac 0x00 /* lcd_data3.lcd_data3, OUTPUT | MODE0 */ + 0xb0 0x00 /* lcd_data4.lcd_data4, OUTPUT | MODE0 */ + 0xb4 0x00 /* lcd_data5.lcd_data5, OUTPUT | MODE0 */ + 0xb8 0x00 /* lcd_data6.lcd_data6, OUTPUT | MODE0 */ + 0xbc 0x00 /* lcd_data7.lcd_data7, OUTPUT | MODE0 */ + 0xc0 0x00 /* lcd_data8.lcd_data8, OUTPUT | MODE0 */ + 0xc4 0x00 /* lcd_data9.lcd_data9, OUTPUT | MODE0 */ + 0xc8 0x00 /* lcd_data10.lcd_data10, OUTPUT | MODE0 */ + 0xcc 0x00 /* lcd_data11.lcd_data11, OUTPUT | MODE0 */ + 0xd0 0x00 /* lcd_data12.lcd_data12, OUTPUT | MODE0 */ + 0xd4 0x00 /* lcd_data13.lcd_data13, OUTPUT | MODE0 */ + 0xd8 0x00 /* lcd_data14.lcd_data14, OUTPUT | MODE0 */ + 0xdc 0x00 /* lcd_data15.lcd_data15, OUTPUT | MODE0 */ + 0xe0 0x00 /* lcd_vsync.lcd_vsync, OUTPUT | MODE0 */ + 0xe4 0x00 /* lcd_hsync.lcd_hsync, OUTPUT | MODE0 */ + 0xe8 0x00 /* lcd_pclk.lcd_pclk, OUTPUT | MODE0 */ + 0xec 0x00 /* lcd_ac_bias_en.lcd_ac_bias_en, OUTPUT | MODE0 */ + >; + }; + + lcd_pins_sleep: lcd_pins_sleep { + pinctrl-single,pins = < + 0x20 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad8.lcd_data16 */ + 0x24 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad9.lcd_data17 */ + 0x28 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad10.lcd_data18 */ + 0x2c (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad11.lcd_data19 */ + 0x30 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad12.lcd_data20 */ + 0x34 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad13.lcd_data21 */ + 0x38 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad14.lcd_data22 */ + 0x3c (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad15.lcd_data23 */ + 0xa0 (PULL_DISABLE | MUX_MODE7) /* lcd_data0.lcd_data0 */ + 0xa4 (PULL_DISABLE | MUX_MODE7) /* lcd_data1.lcd_data1 */ + 0xa8 (PULL_DISABLE | MUX_MODE7) /* lcd_data2.lcd_data2 */ + 0xac (PULL_DISABLE | MUX_MODE7) /* lcd_data3.lcd_data3 */ + 0xb0 (PULL_DISABLE | MUX_MODE7) /* lcd_data4.lcd_data4 */ + 0xb4 (PULL_DISABLE | MUX_MODE7) /* lcd_data5.lcd_data5 */ + 0xb8 (PULL_DISABLE | MUX_MODE7) /* lcd_data6.lcd_data6 */ + 0xbc (PULL_DISABLE | MUX_MODE7) /* lcd_data7.lcd_data7 */ + 0xc0 (PULL_DISABLE | MUX_MODE7) /* lcd_data8.lcd_data8 */ + 0xc4 (PULL_DISABLE | MUX_MODE7) /* lcd_data9.lcd_data9 */ + 0xc8 (PULL_DISABLE | MUX_MODE7) /* lcd_data10.lcd_data10 */ + 0xcc (PULL_DISABLE | MUX_MODE7) /* lcd_data11.lcd_data11 */ + 0xd0 (PULL_DISABLE | MUX_MODE7) /* lcd_data12.lcd_data12 */ + 0xd4 (PULL_DISABLE | MUX_MODE7) /* lcd_data13.lcd_data13 */ + 0xd8 (PULL_DISABLE | MUX_MODE7) /* lcd_data14.lcd_data14 */ + 0xdc (PULL_DISABLE | MUX_MODE7) /* lcd_data15.lcd_data15 */ + /* lcd_vsync.lcd_vsync,OUTPUT | MODE0 */ + 0xe0 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0xe4 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* lcd_hsync.lcd_hsync */ + 0xe8 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* lcd_pclk.lcd_pclk */ + /* lcd_ac_bias_en.lcd_ac_bias_en */ + 0xec (PIN_INPUT_PULLDOWN | MUX_MODE7) + >; + }; + +}; + +&lcdc { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&lcd_pins_default>; + pinctrl-1 = <&lcd_pins_sleep>; + status = "okay"; + /* display-timings { + 480x272 { + hactive = <480>; + vactive = <272>; + hback-porch = <43>; + hfront-porch = <8>; + hsync-len = <4>; + vback-porch = <12>; + vfront-porch = <4>; + vsync-len = <10>; + clock-frequency = <9000000>; + hsync-active = <0>; + vsync-active = <0>; + }; + };*/ + + display-timings { + native-mode = <&vga1024x768>; + lcd4: 480x272 { + clock-frequency = <9000000>; + hactive = <480>; + vactive = <272>; + hfront-porch = <3>; + hback-porch = <40>; + vback-porch = <8>; + vfront-porch = <7>; + hsync-len = <2>; + vsync-len = <1>; + hsync-active = <0>; + vsync-active = <0>; + }; + lcd7: 800x480 { + clock-frequency = <33300000>; + hactive = <800>; + vactive = <480>; + hfront-porch = <210>; + hback-porch = <40>; + vback-porch = <23>; + vfront-porch = <20>; + hsync-len = <6>; + vsync-len = <2>; + hsync-active = <0>; + vsync-active = <0>; + }; + lcd10: 1024x600 { + clock-frequency = <51200000>; + hactive = <1024>; + vactive = <600>; + hfront-porch = <160>; + hback-porch = <140>; + vback-porch = <20>; + vfront-porch = <12>; + hsync-len = <20>; + vsync-len = <3>; + hsync-active = <0>; + vsync-active = <0>; + }; + + vga800x600: 800x600 { + clock-frequency = <40000000>; + hactive = <800>; + vactive = <600>; + hfront-porch = <40>; + hback-porch = <88>; + vfront-porch = <1>; + vback-porch = <23>; + hsync-len = <128>; + vsync-len = <4>; + hsync-active = <0>; + vsync-active = <0>; + }; + vga1024x768: 1024x768 { + clock-frequency = <65000000>; + hactive = <1024>; + hfront-porch = <24>; + hback-porch = <160>; + hsync-len = <136>; + vactive = <768>; + vfront-porch = <3>; + vback-porch = <29>; + vsync-len = <6>; + hsync-active = <0>; + vsync-active = <0>; + }; + }; +}; diff --git b/arch/arm/boot/dts/am335x-peripheral-can0.dtsi b/arch/arm/boot/dts/am335x-peripheral-can0.dtsi new file mode 100644 index 000000000..4335e39bf --- /dev/null +++ b/arch/arm/boot/dts/am335x-peripheral-can0.dtsi @@ -0,0 +1,13 @@ +/* + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +&dcan0 { + pinctrl-names = "default"; + + status = "okay"; +}; diff --git b/arch/arm/boot/dts/am335x-peripheral-can1.dtsi b/arch/arm/boot/dts/am335x-peripheral-can1.dtsi new file mode 100644 index 000000000..02b5bd170 --- /dev/null +++ b/arch/arm/boot/dts/am335x-peripheral-can1.dtsi @@ -0,0 +1,13 @@ +/* + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +&dcan1 { + pinctrl-names = "default"; + + status = "okay"; +}; diff --git b/arch/arm/boot/dts/am335x-peripheral-emmc.dtsi b/arch/arm/boot/dts/am335x-peripheral-emmc.dtsi new file mode 100644 index 000000000..603f34ec6 --- /dev/null +++ b/arch/arm/boot/dts/am335x-peripheral-emmc.dtsi @@ -0,0 +1,15 @@ +/* + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +&mmc2 { + vmmc-supply = <&vmmcsd_fixed>; + pinctrl-names = "default"; + + bus-width = <8>; + status = "okay"; +}; diff --git b/arch/arm/boot/dts/am335x-peripheral-i2c2.dtsi b/arch/arm/boot/dts/am335x-peripheral-i2c2.dtsi new file mode 100644 index 000000000..ed9a0b52f --- /dev/null +++ b/arch/arm/boot/dts/am335x-peripheral-i2c2.dtsi @@ -0,0 +1,13 @@ +/* + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +&i2c2 { + pinctrl-names = "default"; + + status = "okay"; +}; diff --git b/arch/arm/boot/dts/am335x-peripheral-nxp-hdmi.dtsi b/arch/arm/boot/dts/am335x-peripheral-nxp-hdmi.dtsi new file mode 100644 index 000000000..1dfd26a69 --- /dev/null +++ b/arch/arm/boot/dts/am335x-peripheral-nxp-hdmi.dtsi @@ -0,0 +1,29 @@ +/* + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +&lcdc { + status = "okay"; + port { + lcdc_0: endpoint@0 { + remote-endpoint = <&hdmi_0>; + }; + }; +}; + +&i2c0 { + tda19988 { + compatible = "nxp,tda998x"; + reg = <0x70>; + + port { + hdmi_0: endpoint@0 { + remote-endpoint = <&lcdc_0>; + }; + }; + }; +}; diff --git b/arch/arm/boot/dts/am335x-peripheral-panel-1024x600-24bit.dtsi b/arch/arm/boot/dts/am335x-peripheral-panel-1024x600-24bit.dtsi new file mode 100644 index 000000000..74ddc12c0 --- /dev/null +++ b/arch/arm/boot/dts/am335x-peripheral-panel-1024x600-24bit.dtsi @@ -0,0 +1,49 @@ +/* + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +&lcdc { + status = "okay"; +}; + +/ { + panel { + status = "okay"; + compatible = "ti,tilcdc,panel"; + pinctrl-names = "default"; + + panel-info { + ac-bias = <255>; + ac-bias-intrpt = <0>; + dma-burst-sz = <16>; + bpp = <32>; + fdd = <0x80>; + sync-edge = <0>; + sync-ctrl = <0>; + raster-order = <1>; + fifo-th = <0>; + }; + display-timings { + native-mode = <&timing0>; + timing0: 1024x600 { + clock-frequency = <36000000>; + hactive = <1024>; + vactive = <600>; + hfront-porch = <1>; + hback-porch = <45>; + hsync-len = <30>; + vback-porch = <22>; + vfront-porch = <12>; + vsync-len = <2>; + hsync-active = <1>; + vsync-active = <1>; + de-active = <1>; + pixelclk-active = <0>; + }; + }; + }; +}; diff --git b/arch/arm/boot/dts/am335x-peripheral-spi0.dtsi b/arch/arm/boot/dts/am335x-peripheral-spi0.dtsi new file mode 100644 index 000000000..969e35259 --- /dev/null +++ b/arch/arm/boot/dts/am335x-peripheral-spi0.dtsi @@ -0,0 +1,13 @@ +/* + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +&spi0 { + pinctrl-names = "default"; + + status = "okay"; +}; diff --git b/arch/arm/boot/dts/am335x-peripheral-spi1.dtsi b/arch/arm/boot/dts/am335x-peripheral-spi1.dtsi new file mode 100644 index 000000000..ac5fe97b6 --- /dev/null +++ b/arch/arm/boot/dts/am335x-peripheral-spi1.dtsi @@ -0,0 +1,13 @@ +/* + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +&spi1 { + pinctrl-names = "default"; + + status = "okay"; +}; diff --git b/arch/arm/boot/dts/am335x-peripheral-spi1a.dtsi b/arch/arm/boot/dts/am335x-peripheral-spi1a.dtsi new file mode 100644 index 000000000..ac5fe97b6 --- /dev/null +++ b/arch/arm/boot/dts/am335x-peripheral-spi1a.dtsi @@ -0,0 +1,13 @@ +/* + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +&spi1 { + pinctrl-names = "default"; + + status = "okay"; +}; diff --git b/arch/arm/boot/dts/am335x-peripheral-ttyS1.dtsi b/arch/arm/boot/dts/am335x-peripheral-ttyS1.dtsi new file mode 100644 index 000000000..f59fa4c50 --- /dev/null +++ b/arch/arm/boot/dts/am335x-peripheral-ttyS1.dtsi @@ -0,0 +1,13 @@ +/* + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +&uart1 { + pinctrl-names = "default"; + + status = "okay"; +}; diff --git b/arch/arm/boot/dts/am335x-peripheral-ttyS2.dtsi b/arch/arm/boot/dts/am335x-peripheral-ttyS2.dtsi new file mode 100644 index 000000000..a25d6cfcb --- /dev/null +++ b/arch/arm/boot/dts/am335x-peripheral-ttyS2.dtsi @@ -0,0 +1,13 @@ +/* + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +&uart2 { + pinctrl-names = "default"; + + status = "okay"; +}; diff --git b/arch/arm/boot/dts/am335x-peripheral-ttyS4.dtsi b/arch/arm/boot/dts/am335x-peripheral-ttyS4.dtsi new file mode 100644 index 000000000..adc89f046 --- /dev/null +++ b/arch/arm/boot/dts/am335x-peripheral-ttyS4.dtsi @@ -0,0 +1,13 @@ +/* + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +&uart4 { + pinctrl-names = "default"; + + status = "okay"; +}; diff --git b/arch/arm/boot/dts/am335x-peripheral-ttyS5.dtsi b/arch/arm/boot/dts/am335x-peripheral-ttyS5.dtsi new file mode 100644 index 000000000..8b42fb02b --- /dev/null +++ b/arch/arm/boot/dts/am335x-peripheral-ttyS5.dtsi @@ -0,0 +1,13 @@ +/* + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +&uart5 { + pinctrl-names = "default"; + + status = "okay"; +}; diff --git b/arch/arm/boot/dts/am335x-roboticscape.dtsi b/arch/arm/boot/dts/am335x-roboticscape.dtsi new file mode 100644 index 000000000..77d815a3a --- /dev/null +++ b/arch/arm/boot/dts/am335x-roboticscape.dtsi @@ -0,0 +1,395 @@ +/******************************************************************************* +* pinmux and modules used by roboticscape +* included in: +* am335x-boneblack-roboticscape.dts +* am335x-boneblack-wireless-roboticscape.dts +*******************************************************************************/ + + + +/******************************************************************************* +* Pin Muxing +*******************************************************************************/ +&am33xx_pinmux { + + /*************************************************************************** + * Static Pinmux + ***************************************************************************/ + mux_helper_pins: pins { + pinctrl-single,pins = < + + /* GPIO Input Pullup */ + 0x09c 0x37 /*P8.9 T6 PAUSE_BTN */ + 0x098 0x37 /*P8.10 U6 MODE_BTN */ + 0x1AC 0x37 /*P9.25 A14 IMU_INT */ + + /* LEDs GPIO Out*/ + 0x090 0x0F /* P8.7 R7 LED_RED */ + 0x094 0x0F /* P8.8 T7 LED_GREEN */ + 0x028 0x0F /*P8.14 T11 BATT_LED_4 */ + 0x02C 0x0F /*P8.17 U12 BATT_LED_1 */ + 0x08c 0x0F /*P8.18 V12 BATT_LED_2 */ + 0x07c 0x0F /*P8.26 V6 BATT_LED_3 */ + + /* Motor Control GPIO Out*/ + 0x0cc 0x0F /*P8.34 MDIR_2B different from blue!!*/ + 0x0a8 0x0F /*P8.43 MDIR_3B*/ + 0x0ac 0x0F /*P8.44 MDIR_3A*/ + 0x0a0 0x0F /*P8.45 MDIR_4A*/ + 0x0a4 0x0F /*P8.46 MDIR_4B*/ + 0x078 0x0F /*P9.12 MDIR_1A different from blue!!*/ + 0x074 0x0F /*P9.13 MDIR_1B*/ + 0x040 0x0F /*P9.15 MDIR_2A*/ + 0x1b4 0x0F /*P9.41 MOT_STBY*/ + + /* HRPWM 1 */ + 0x048 0x6 /* P9_14 | MODE 6 */ + 0x04c 0x6 /* P9_16 | MODE 6 */ + + /* HRPWM 2 */ + 0x020 0x4 /* P8_19 | MODE 4 */ + 0x024 0x4 /* P8_13 | MODE 4 */ + + /* EQEP */ + 0x1A0 0x31 /* P9_42,EQEP0A, MODE1 */ + 0x1A4 0x31 /* P9_27,EQEP0B, MODE1 */ + 0x0D4 0x32 /* P8_33,EQEP1B, MODE2 */ + 0x0D0 0x32 /* P8_35,EQEP1A, MODE2 */ + 0x030 0x34 /* P8_12,EQEP2A, MODE4 */ + 0x034 0x34 /* P8_11,EQEP2B, MODE4 */ + + /* PRU encoder input */ + 0x03c 0x36 /* P8_15,PRU0_r31_15,MODE6 */ + 0x038 0x36 /* P8_16,PRU0_r31_16,MODE6 */ + + /* PRU Servo output */ + 0x0e0 0x05 /*pru1_pru_r30_8, MODE5*/ + 0x0e8 0x05 /*pru1_pru_r30_10, MODE5 */ + 0x0e4 0x05 /*pr1_pru1_pru_r30_9, MODE5 */ + 0x0ec 0x05 /*pru1_pru_r30_11, MODE5 */ + 0x0b8 0x05 /*pru1_pru_r30_6, MODE5 */ + 0x0bc 0x05 /*pru1_pru_r30_7, MODE5 */ + 0x0b0 0x05 /*pru1_pru_r30_4, MODE5 */ + 0x0b4 0x05 /*pru1_pru_r30_5, MODE5 */ + 0x0C8 0x0F /*P8.36, SERVO_PWR GPIO OUT*/ + + /* I2C1 */ + 0x15C 0x32 /* P9.17,i2c1_scl,INPUT_PULLUP,MODE2 */ + 0x158 0x32 /* P9.18,i2c1_sda,INPUT_PULLUP,MODE2 */ + + /* I2C2 */ + 0x17c 0x73 /* P9.19, i2c2_sda, mode 3 */ + 0x178 0x73 /* P9.20, i2c2_sda, mode 3 */ + + /* UART5 */ + 0x0C4 0x34 /* P8.38,uart5_rxd,MODE4 */ + 0x0C0 0x14 /* P8.37,uart5_txd,MODE4 */ + + >; + }; + +}; + + +/******************************************************************************* +* apply static and dynamic pinmux modes listed above. Configurable pins get the +* modes from am335x-boneblack-common-universal-pins.dtsi +*******************************************************************************/ +&ocp { + /* activate the static pinmux helper list of pin modes above */ + test_helper: helper { + compatible = "bone-pinmux-helper"; + pinctrl-names = "default"; + pinctrl-0 = <&mux_helper_pins>; + + status = "okay"; + }; + + /* UART4 RX DSM */ + P9_11_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "uart"; + pinctrl-0 = <&P9_11_default_pin>; + pinctrl-1 = <&P9_11_gpio_pin>; + pinctrl-2 = <&P9_11_gpio_pu_pin>; + pinctrl-3 = <&P9_11_gpio_pd_pin>; + pinctrl-4 = <&P9_11_uart_pin>; + }; + + /* UART 2 TX GPS*/ + P9_21_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "spi", "uart", "i2c", "pwm"; + pinctrl-0 = <&P9_21_default_pin>; + pinctrl-1 = <&P9_21_gpio_pin>; + pinctrl-2 = <&P9_21_gpio_pu_pin>; + pinctrl-3 = <&P9_21_gpio_pd_pin>; + pinctrl-4 = <&P9_21_spi_pin>; + pinctrl-5 = <&P9_21_uart_pin>; + pinctrl-6 = <&P9_21_i2c_pin>; + pinctrl-7 = <&P9_21_pwm_pin>; + }; + + /* UART 2 RX GPS */ + P9_22_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "spi", "uart", "i2c", "pwm"; + pinctrl-0 = <&P9_22_default_pin>; + pinctrl-1 = <&P9_22_gpio_pin>; + pinctrl-2 = <&P9_22_gpio_pu_pin>; + pinctrl-3 = <&P9_22_gpio_pd_pin>; + pinctrl-4 = <&P9_22_spi_pin>; + pinctrl-5 = <&P9_22_uart_pin>; + pinctrl-6 = <&P9_22_i2c_pin>; + pinctrl-7 = <&P9_22_pwm_pin>; + }; + + /* SPI MISO */ + P9_29_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "pwm", "spi", "pruout", "pruin"; + pinctrl-0 = <&P9_29_default_pin>; + pinctrl-1 = <&P9_29_gpio_pin>; + pinctrl-2 = <&P9_29_gpio_pu_pin>; + pinctrl-3 = <&P9_29_gpio_pd_pin>; + pinctrl-4 = <&P9_29_pwm_pin>; + pinctrl-5 = <&P9_29_spi_pin>; + pinctrl-6 = <&P9_29_pruout_pin>; + pinctrl-7 = <&P9_29_pruin_pin>; + }; + + /* SPI MOSI */ + P9_30_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "pwm", "spi", "pruout", "pruin"; + pinctrl-0 = <&P9_30_default_pin>; + pinctrl-1 = <&P9_30_gpio_pin>; + pinctrl-2 = <&P9_30_gpio_pu_pin>; + pinctrl-3 = <&P9_30_gpio_pd_pin>; + pinctrl-4 = <&P9_30_pwm_pin>; + pinctrl-5 = <&P9_30_spi_pin>; + pinctrl-6 = <&P9_30_pruout_pin>; + pinctrl-7 = <&P9_30_pruin_pin>; + }; + + /* SPI SCK */ + P9_31_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "pwm", "spi", "pruout", "pruin"; + pinctrl-0 = <&P9_31_default_pin>; + pinctrl-1 = <&P9_31_gpio_pin>; + pinctrl-2 = <&P9_31_gpio_pu_pin>; + pinctrl-3 = <&P9_31_gpio_pd_pin>; + pinctrl-4 = <&P9_31_pwm_pin>; + pinctrl-5 = <&P9_31_spi_pin>; + pinctrl-6 = <&P9_31_pruout_pin>; + pinctrl-7 = <&P9_31_pruin_pin>; + }; + + /* SPI SS1 GPIO3_17*/ + P9_28_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "pwm", "spi", "pwm2", "pruout", "pruin"; + pinctrl-0 = <&P9_28_default_pin>; + pinctrl-1 = <&P9_28_gpio_pin>; + pinctrl-2 = <&P9_28_gpio_pu_pin>; + pinctrl-3 = <&P9_28_gpio_pd_pin>; + pinctrl-4 = <&P9_28_pwm_pin>; + pinctrl-5 = <&P9_28_spi_pin>; + pinctrl-6 = <&P9_28_pwm2_pin>; + pinctrl-7 = <&P9_28_pruout_pin>; + pinctrl-8 = <&P9_28_pruin_pin>; + }; + + /* SPI SS1 GPIO1_17*/ + P9_23_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "pwm"; + pinctrl-0 = <&P9_23_default_pin>; + pinctrl-1 = <&P9_23_gpio_pin>; + pinctrl-2 = <&P9_23_gpio_pu_pin>; + pinctrl-3 = <&P9_23_gpio_pd_pin>; + pinctrl-4 = <&P9_23_pwm_pin>; + }; + + /* UART 1 TX */ + P9_24_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "uart", "can", "i2c", "pruin"; + pinctrl-0 = <&P9_24_default_pin>; + pinctrl-1 = <&P9_24_gpio_pin>; + pinctrl-2 = <&P9_24_gpio_pu_pin>; + pinctrl-3 = <&P9_24_gpio_pd_pin>; + pinctrl-4 = <&P9_24_uart_pin>; + pinctrl-5 = <&P9_24_can_pin>; + pinctrl-6 = <&P9_24_i2c_pin>; + pinctrl-7 = <&P9_24_pruin_pin>; + }; + + /* UART 1 RX */ + P9_26_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "uart", "can", "i2c", "pruin"; + pinctrl-0 = <&P9_26_default_pin>; + pinctrl-1 = <&P9_26_gpio_pin>; + pinctrl-2 = <&P9_26_gpio_pu_pin>; + pinctrl-3 = <&P9_26_gpio_pd_pin>; + pinctrl-4 = <&P9_26_uart_pin>; + pinctrl-5 = <&P9_26_can_pin>; + pinctrl-6 = <&P9_26_i2c_pin>; + pinctrl-7 = <&P9_26_pruin_pin>; + }; + + +}; + + +/******************************************************************************* +* PWMSS +*******************************************************************************/ +&epwmss0 { + status = "okay"; +}; + +&epwmss1 { + status = "okay"; +}; + +&epwmss2 { + status = "okay"; +}; + +&ehrpwm0 { + status = "okay"; +}; + +&ehrpwm1 { + status = "okay"; +}; + +&ehrpwm2 { + status = "okay"; +}; + +/******************************************************************************* +* EQEP +*******************************************************************************/ +&eqep0 { + count_mode = <0>; /* 0 - Quadrature mode, normal 90 phase offset cha & chb. 1 - Direction mode. cha input = clock, chb input = direction */ + swap_inputs = <0>; /* Are channel A and channel B swapped? (0 - no, 1 - yes) */ + invert_qa = <1>; /* Should we invert the channel A input? */ + invert_qb = <1>; /* Should we invert the channel B input? I invert these because my encoder outputs drive transistors that pull down the pins */ + invert_qi = <0>; /* Should we invert the index input? */ + invert_qs = <0>; /* Should we invert the strobe input? */ + + status = "okay"; +}; + +&eqep1 { + count_mode = <0>; /* 0 - Quadrature mode, normal 90 phase offset cha & chb. 1 - Direction mode. cha input = clock, chb input = direction */ + swap_inputs = <0>; /* Are channel A and channel B swapped? (0 - no, 1 - yes) */ + invert_qa = <1>; /* Should we invert the channel A input? */ + invert_qb = <1>; /* Should we invert the channel B input? I invert these because my encoder outputs drive transistors that pull down the pins */ + invert_qi = <0>; /* Should we invert the index input? */ + invert_qs = <0>; /* Should we invert the strobe input? */ + + status = "okay"; +}; + +&eqep2 { + count_mode = <0>; /* 0 - Quadrature mode, normal 90 phase offset cha & chb. 1 - Direction mode. cha input = clock, chb input = direction */ + swap_inputs = <0>; /* Are channel A and channel B swapped? (0 - no, 1 - yes) */ + invert_qa = <1>; /* Should we invert the channel A input? */ + invert_qb = <1>; /* Should we invert the channel B input? I invert these because my encoder outputs drive transistors that pull down the pins */ + invert_qi = <0>; /* Should we invert the index input? */ + invert_qs = <0>; /* Should we invert the strobe input? */ + + status = "okay"; +}; + + +/******************************************************************************* +* UART +*******************************************************************************/ +&uart1 { + status = "okay"; +}; + +&uart2 { + status = "okay"; +}; + +&uart4 { + status = "okay"; +}; + +&uart5 { + status = "okay"; +}; + + +/******************************************************************************* +* PRU Encoder and Servos +*******************************************************************************/ +&pruss { + status = "okay"; +}; + + +/******************************************************************************* +* I2C +*******************************************************************************/ +&i2c1 { + status = "okay"; + clock-frequency = <400000>; + #address-cells = <1>; + #size-cells = <0>; +}; + +&i2c2 { + status = "okay"; + clock-frequency = <400000>; + #address-cells = <1>; + #size-cells = <0>; +}; + + +/******************************************************************************* +* SPI +*******************************************************************************/ +&spi1 { + #address-cells = <1>; + #size-cells = <0>; + status = "okay"; + + channel@0 { + #address-cells = <1>; + #size-cells = <0>; + + compatible = "spidev"; + + reg = <0>; + spi-max-frequency = <16000000>; + spi-cpha; + }; + + channel@1 { + #address-cells = <1>; + #size-cells = <0>; + + compatible = "spidev"; + + reg = <1>; + spi-max-frequency = <16000000>; + }; +}; diff --git b/arch/arm/boot/dts/am335x-sancloud-bbe.dts b/arch/arm/boot/dts/am335x-sancloud-bbe.dts new file mode 100644 index 000000000..a36b04b75 --- /dev/null +++ b/arch/arm/boot/dts/am335x-sancloud-bbe.dts @@ -0,0 +1,264 @@ +/* + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +/dts-v1/; + +#include "am33xx.dtsi" +#include "am335x-bone-common.dtsi" +#include +#include +/* #include "am335x-bone-jtag.dtsi" */ + +/ { + model = "SanCloud BeagleBone Enhanced"; + compatible = "sancloud,am335x-boneenhanced", "ti,am335x-bone-black", "ti,am335x-bone", "ti,am33xx"; +}; + +&ldo3_reg { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; +}; + +&mmc1 { + vmmc-supply = <&vmmcsd_fixed>; +}; + +&mmc2 { + vmmc-supply = <&vmmcsd_fixed>; + pinctrl-names = "default"; + pinctrl-0 = <&emmc_pins>; + bus-width = <8>; + status = "okay"; + ti,vcc-aux-disable-is-sleep; +}; + +&am33xx_pinmux { + pinctrl-names = "default"; + pinctrl-0 = <&usb_hub_ctrl>; + + nxp_hdmi_bonelt_pins: nxp_hdmi_bonelt_pins { + pinctrl-single,pins = < + AM33XX_IOPAD(0x9b0, PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* xdma_event_intr0 */ + AM33XX_IOPAD(0x8a0, PIN_OUTPUT | MUX_MODE0) /* lcd_data0.lcd_data0 */ + AM33XX_IOPAD(0x8a4, PIN_OUTPUT | MUX_MODE0) /* lcd_data1.lcd_data1 */ + AM33XX_IOPAD(0x8a8, PIN_OUTPUT | MUX_MODE0) /* lcd_data2.lcd_data2 */ + AM33XX_IOPAD(0x8ac, PIN_OUTPUT | MUX_MODE0) /* lcd_data3.lcd_data3 */ + AM33XX_IOPAD(0x8b0, PIN_OUTPUT | MUX_MODE0) /* lcd_data4.lcd_data4 */ + AM33XX_IOPAD(0x8b4, PIN_OUTPUT | MUX_MODE0) /* lcd_data5.lcd_data5 */ + AM33XX_IOPAD(0x8b8, PIN_OUTPUT | MUX_MODE0) /* lcd_data6.lcd_data6 */ + AM33XX_IOPAD(0x8bc, PIN_OUTPUT | MUX_MODE0) /* lcd_data7.lcd_data7 */ + AM33XX_IOPAD(0x8c0, PIN_OUTPUT | MUX_MODE0) /* lcd_data8.lcd_data8 */ + AM33XX_IOPAD(0x8c4, PIN_OUTPUT | MUX_MODE0) /* lcd_data9.lcd_data9 */ + AM33XX_IOPAD(0x8c8, PIN_OUTPUT | MUX_MODE0) /* lcd_data10.lcd_data10 */ + AM33XX_IOPAD(0x8cc, PIN_OUTPUT | MUX_MODE0) /* lcd_data11.lcd_data11 */ + AM33XX_IOPAD(0x8d0, PIN_OUTPUT | MUX_MODE0) /* lcd_data12.lcd_data12 */ + AM33XX_IOPAD(0x8d4, PIN_OUTPUT | MUX_MODE0) /* lcd_data13.lcd_data13 */ + AM33XX_IOPAD(0x8d8, PIN_OUTPUT | MUX_MODE0) /* lcd_data14.lcd_data14 */ + AM33XX_IOPAD(0x8dc, PIN_OUTPUT | MUX_MODE0) /* lcd_data15.lcd_data15 */ + AM33XX_IOPAD(0x8e0, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* lcd_vsync.lcd_vsync */ + AM33XX_IOPAD(0x8e4, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* lcd_hsync.lcd_hsync */ + AM33XX_IOPAD(0x8e8, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* lcd_pclk.lcd_pclk */ + AM33XX_IOPAD(0x8ec, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* lcd_ac_bias_en.lcd_ac_bias_en */ + >; + }; + nxp_hdmi_bonelt_off_pins: nxp_hdmi_bonelt_off_pins { + pinctrl-single,pins = < + AM33XX_IOPAD(0x9b0, PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* xdma_event_intr0 */ + >; + }; + + cpsw_default: cpsw_default { + pinctrl-single,pins = < + /* Slave 1 */ + 0x114 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txen.rgmii1_tctl */ + 0x118 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxdv.rgmii1_rctl */ + 0x11c (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd3.rgmii1_td3 */ + 0x120 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd2.rgmii1_td2 */ + 0x124 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd1.rgmii1_td1 */ + 0x128 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd0.rgmii1_td0 */ + 0x12c (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txclk.rgmii1_tclk */ + 0x130 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxclk.rgmii1_rclk */ + 0x134 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd3.rgmii1_rd3 */ + 0x138 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd2.rgmii1_rd2 */ + 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd1.rgmii1_rd1 */ + 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd0.rgmii1_rd0 */ + >; + }; + + cpsw_sleep: cpsw_sleep { + pinctrl-single,pins = < + /* Slave 1 reset value */ + 0x114 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x118 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x11c (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x120 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x124 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x128 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x12c (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x130 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x134 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x138 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE7) + >; + }; + + davinci_mdio_default: davinci_mdio_default { + pinctrl-single,pins = < + /* MDIO */ + 0x148 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* mdio_data.mdio_data */ + 0x14c (PIN_OUTPUT_PULLUP | MUX_MODE0) /* mdio_clk.mdio_clk */ + >; + }; + + davinci_mdio_sleep: davinci_mdio_sleep { + pinctrl-single,pins = < + /* MDIO reset value */ + 0x148 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x14c (PIN_INPUT_PULLDOWN | MUX_MODE7) + >; + }; + + usb_hub_ctrl: usb_hub_ctrl { + pinctrl-single,pins = < + 0x144 (PIN_OUTPUT_PULLUP | MUX_MODE7) /* mcasp0_ahclkr.gpio3_17 */ + >; + }; + + mpu6050_pins: pinmux_mpu6050_pins { + pinctrl-single,pins = < + 0x168 (PIN_INPUT | MUX_MODE7) /* spi0_sclk.gpio0_2 */ + >; + }; + + lps3331ap_pins: pinmux_lps3331ap_pins { + pinctrl-single,pins = < + 0x6C (PIN_INPUT | MUX_MODE7) /* conf_gpmc_a11.gpio1_27 */ + >; + }; + + mcasp0_pins: mcasp0_pins { + pinctrl-single,pins = < + AM33XX_IOPAD(0x9ac, PIN_INPUT_PULLUP | MUX_MODE0) /* mcasp0_ahcklx.mcasp0_ahclkx */ + AM33XX_IOPAD(0x99c, PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mcasp0_ahclkr.mcasp0_axr2*/ + AM33XX_IOPAD(0x994, PIN_OUTPUT_PULLUP | MUX_MODE0) /* mcasp0_fsx.mcasp0_fsx */ + AM33XX_IOPAD(0x990, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mcasp0_aclkx.mcasp0_aclkx */ + AM33XX_IOPAD(0x86c, PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a11.GPIO1_27 */ + >; + }; +}; + +&lcdc { + status = "okay"; + port { + lcdc_0: endpoint@0 { + remote-endpoint = <&hdmi_0>; + }; + }; +}; + +&mac { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&cpsw_default>; + pinctrl-1 = <&cpsw_sleep>; +}; + +&davinci_mdio { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&davinci_mdio_default>; + pinctrl-1 = <&davinci_mdio_sleep>; +}; + +&cpsw_emac0 { + phy_id = <&davinci_mdio>, <0>; + phy-mode = "rgmii-txid"; +}; + +&i2c0 { + tda19988: tda19988 { + compatible = "nxp,tda998x"; + reg = <0x70>; + + pinctrl-names = "default", "off"; + pinctrl-0 = <&nxp_hdmi_bonelt_pins>; + pinctrl-1 = <&nxp_hdmi_bonelt_off_pins>; + + #sound-dai-cells = <0>; + audio-ports = < TDA998x_I2S 0x03>; + + ports { + port@0 { + hdmi_0: endpoint@0 { + remote-endpoint = <&lcdc_0>; + }; + }; + }; + }; + + lps331ap: lps331ap@5C { + compatible = "st,lps331ap"; + st,drdy-int-pin = <1>; + reg = <0x5C>; + interrupt-parent = <&gpio1>; + interrupts = <27 IRQ_TYPE_EDGE_RISING>; + }; + + mpu6050: mpu6050@68 { + compatible = "invensense,mpu6050"; + reg = <0x68>; + interrupt-parent = <&gpio0>; + interrupts = <2 IRQ_TYPE_EDGE_RISING>; + //orientation = <0xff 0 0 0 1 0 0 0 0xff>; + }; +}; + +&mcasp0 { + #sound-dai-cells = <0>; + pinctrl-names = "default"; + pinctrl-0 = <&mcasp0_pins>; + status = "okay"; + op-mode = <0>; /* MCASP_IIS_MODE */ + tdm-slots = <2>; + serial-dir = < /* 0: INACTIVE, 1: TX, 2: RX */ + 0 0 1 0 + >; + tx-num-evt = <32>; + rx-num-evt = <32>; +}; + +/ { + clk_mcasp0_fixed: clk_mcasp0_fixed { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <24576000>; + }; + + clk_mcasp0: clk_mcasp0 { + #clock-cells = <0>; + compatible = "gpio-gate-clock"; + clocks = <&clk_mcasp0_fixed>; + enable-gpios = <&gpio1 27 0>; /* BeagleBone Black Clk enable on GPIO1_27 */ + }; + + sound { + compatible = "simple-audio-card"; + simple-audio-card,name = "TI BeagleBone Black"; + simple-audio-card,format = "i2s"; + simple-audio-card,bitclock-master = <&dailink0_master>; + simple-audio-card,frame-master = <&dailink0_master>; + + dailink0_master: simple-audio-card,cpu { + sound-dai = <&mcasp0>; + clocks = <&clk_mcasp0>; + }; + + simple-audio-card,codec { + sound-dai = <&tda19988>; + }; + }; +}; diff --git b/arch/arm/boot/dts/am335x-som-common.dtsi b/arch/arm/boot/dts/am335x-som-common.dtsi new file mode 100644 index 000000000..fb4399b6f --- /dev/null +++ b/arch/arm/boot/dts/am335x-som-common.dtsi @@ -0,0 +1,465 @@ +/* + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +/ { + + cpus { + cpu@0 { + cpu0-supply = <&dcdc2_fixed>; + }; + }; + + memory { + device_type = "memory"; + reg = <0x80000000 0x20000000>; /* 512 MB */ + }; + + ocp { + uart0: serial@44e09000 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_pins>; + + status = "okay"; + }; + uart1: serial@48022000 { + pinctrl-names = "default"; + pinctrl-0 = <&uart1_pins>; + status = "okay"; + + }; + uart4: serial@481a8000 { + pinctrl-names = "default"; + pinctrl-0 = <&uart4_pins>; + status = "okay"; + }; + + epwmss0: epwmss@48300000 { + status = "okay"; + + ecap0: ecap@48300100 { + status = "okay"; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&ecap0_pins_default>; + pinctrl-1 = <&ecap0_pins_sleep>; + }; + }; + + musb: usb@47400000 { + status = "okay"; + + control@44e10000 { + status = "okay"; + }; + + usb-phy@47401300 { + status = "okay"; + }; + + usb-phy@47401b00 { + status = "okay"; + }; + + usb@47401000 { + status = "okay"; + dr_mode = "otg"; + }; + + usb@47401800 { + status = "okay"; + dr_mode = "host"; + }; + + dma-controller@07402000 { + status = "okay"; + }; + }; + + i2c0: i2c@44e0b000 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_pins>; + status = "okay"; + clock-frequency = <100000>; + + tps: tps@24 { + reg = <0x24>; + }; + }; + }; + + vmmcsd_fixed: fixedregulator@0 { + compatible = "regulator-fixed"; + regulator-name = "vmmcsd_fixed"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + dcdc2_fixed: fixedregulator@1 { + /* VDD_MPU voltage limits 0.95V - 1.325V with +/-4% tolerance */ + compatible = "regulator-fixed"; + regulator-name = "dcdc2_fixed"; + + regulator-min-microvolt = <1378000>; + regulator-max-microvolt = <1378000>; + regulator-boot-on; + regulator-always-on; + }; + + leds { + pinctrl-names = "default"; + pinctrl-0 = <&user_leds_s0>; + + compatible = "gpio-leds"; + + led@1 { + label = "led1:green:heartbeat"; + gpios = <&gpio0 19 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "heartbeat"; + }; + + led@2 { + label = "led2:red:heartbeat"; + gpios = <&gpio3 20 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "heartbeat"; + }; + + led@3 { + label = "led3:yello:heartbeat"; + gpios = <&gpio3 21 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "heartbeat"; + }; + + led@4 { + label = "bkl"; + gpios = <&gpio3 19 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "default-on"; + }; + }; + + backlight { + compatible = "pwm-backlight"; + pwms = <&ecap0 0 500000 1>; + brightness-levels = < + 0 1 2 3 4 5 6 7 8 9 + 10 11 12 13 14 15 16 17 18 19 + 20 21 22 23 24 25 26 27 28 29 + 30 31 32 33 34 35 36 37 38 39 + 40 41 42 43 44 45 46 47 48 49 + 50 51 52 53 54 55 56 57 58 59 + 60 61 62 63 64 65 66 67 68 69 + 70 71 72 73 74 75 76 77 78 79 + 80 81 82 83 84 85 86 87 88 89 + 90 91 92 93 94 95 96 97 98 99 + 100 + >; + default-brightness-level = <50>; + }; +}; + +&am33xx_pinmux { + pinctrl-names = "default"; + pinctrl-0 = <&clkout2_pin>; + + user_leds_s0: user_leds_s0 { + pinctrl-single,pins = < + 0x1b0 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* xdma_event_intr0.gpio0_19 */ + 0x198 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* mcasp0_axr0.gpio3_20 */ + 0x1a8 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* mcasp0_axr1.gpio3_21 */ + 0x1a4 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* mcasp0_fsr.gpio3[19], INPUT_PULLDOWN | MODE7 */ + >; + }; + + i2c0_pins: pinmux_i2c0_pins { + pinctrl-single,pins = < + 0x188 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_sda.i2c0_sda */ + 0x18c (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_scl.i2c0_scl */ + >; + }; + + uart0_pins: pinmux_uart0_pins { + pinctrl-single,pins = < + 0x170 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart0_rxd.uart0_rxd */ + 0x174 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart0_txd.uart0_txd */ + >; + }; + + uart1_pins: pinmux_uart1_pins { + pinctrl-single,pins = < + 0x168 (PIN_INPUT_PULLUP | MUX_MODE1) + 0x16c (PIN_OUTPUT_PULLDOWN | MUX_MODE1) + >; + }; + + uart4_pins: pinmux_uart4_pins { + pinctrl-single,pins = < + 0x180 (PIN_INPUT_PULLUP | MUX_MODE0) + 0x184 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) + >; + }; + + + + clkout2_pin: pinmux_clkout2_pin { + pinctrl-single,pins = < + 0x1b4 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* xdma_event_intr1.clkout2 */ + >; + }; + + cpsw_default: cpsw_default { + pinctrl-single,pins = < + /* Slave 1 */ + 0x110 (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxerr.mii1_rxerr */ + 0x114 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mii1_txen.mii1_txen */ + 0x118 (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxdv.mii1_rxdv */ + 0x11c (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mii1_txd3.mii1_txd3 */ + 0x120 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mii1_txd2.mii1_txd2 */ + 0x124 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mii1_txd1.mii1_txd1 */ + 0x128 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mii1_txd0.mii1_txd0 */ + 0x12c (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_txclk.mii1_txclk */ + 0x130 (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxclk.mii1_rxclk */ + 0x134 (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxd3.mii1_rxd3 */ + 0x138 (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxd2.mii1_rxd2 */ + 0x13c (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxd1.mii1_rxd1 */ + 0x140 (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxd0.mii1_rxd0 */ + + 0x040 (PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* gpmc_a0.gmii2_txen, OUTPUT_PULLDOWN | MODE1 */ + 0x044 (PIN_INPUT_PULLDOWN | MUX_MODE1 ) /* gpmc_a1.gmii2_rxdv, INPUT_PULLDOWN | MODE1 */ + 0x048 (PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* gpmc_a2.gmii2_txd3, OUTPUT_PULLDOWN | MODE1 */ + 0x04c (PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* gpmc_a3.gmii2_txd2, OUTPUT_PULLDOWN | MODE1 */ + 0x050 (PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* gpmc_a4.gmii2_txd1, OUTPUT_PULLDOWN | MODE1 */ + 0x054 (PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* gpmc_a5.gmii2_txd0, OUTPUT_PULLDOWN | MODE1 */ + 0x058 (PIN_INPUT_PULLDOWN | MUX_MODE1 ) /* gpmc_a6.gmii2_txclk, INPUT_PULLDOWN | MODE1 */ + 0x05c (PIN_INPUT_PULLDOWN | MUX_MODE1 ) /* gpmc_a7.gmii2_rxclk, INPUT_PULLDOWN | MODE1 */ + 0x060 (PIN_INPUT_PULLDOWN | MUX_MODE1 ) /* gpmc_a8.gmii2_rxd3, INPUT_PULLDOWN | MODE1 */ + 0x064 (PIN_INPUT_PULLDOWN | MUX_MODE1 ) /* gpmc_a9.gmii2_rxd2, INPUT_PULLDOWN | MODE1 */ + 0x068 (PIN_INPUT_PULLDOWN | MUX_MODE1 ) /* gpmc_a10.gmii2_rxd1, INPUT_PULLDOWN | MODE1 */ + 0x06c (PIN_INPUT_PULLDOWN | MUX_MODE1 ) /* gpmc_a11.gmii2_rxd0, INPUT_PULLDOWN | MODE1 */ + 0x070 (PIN_INPUT_PULLUP | MUX_MODE1 ) /* gpmc_wait0.gmii2_crs, INPUT_PULLUP | MODE1 */ + 0x074 (PIN_INPUT_PULLUP | MUX_MODE1 ) /* gpmc_wpn.gmii2_rxer, INPUT_PULLUP | MODE1 */ + 0x078 (PIN_INPUT_PULLUP | MUX_MODE1 ) /* gpmc_ben1.gmii2_col, INPUT_PULLUP | MODE1 */ + >; + }; + + cpsw_sleep: cpsw_sleep { + pinctrl-single,pins = < + /* Slave 1 reset value */ + 0x110 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x114 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x118 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x11c (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x120 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x124 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x128 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x12c (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x130 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x134 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x138 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE7) + + 0x40 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x44 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x48 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x4c (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x50 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x54 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x58 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x5c (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x60 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x64 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x68 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x6c (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x070 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x074 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x078 (PIN_INPUT_PULLDOWN | MUX_MODE7) + >; + }; + + davinci_mdio_default: davinci_mdio_default { + pinctrl-single,pins = < + /* MDIO */ + 0x148 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* mdio_data.mdio_data */ + 0x14c (PIN_OUTPUT_PULLUP | MUX_MODE0) /* mdio_clk.mdio_clk */ + >; + }; + + davinci_mdio_sleep: davinci_mdio_sleep { + pinctrl-single,pins = < + /* MDIO reset value */ + 0x148 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x14c (PIN_INPUT_PULLDOWN | MUX_MODE7) + >; + }; + + mmc1_pins_default: pinmux_mmc1_pins { + pinctrl-single,pins = < + 0x0F0 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat3.mmc0_dat3 */ + 0x0F4 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat2.mmc0_dat2 */ + 0x0F8 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat1.mmc0_dat1 */ + 0x0FC (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat0.mmc0_dat0 */ + 0x100 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_clk.mmc0_clk */ + 0x104 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_cmd.mmc0_cmd */ + 0x1A0 (PIN_INPUT_PULLUP | MUX_MODE7) /* mcasp0_aclkr.gpio3_18 */ + 0x160 (PIN_INPUT | MUX_MODE7) /* spi0_cs1.gpio0_6 */ + >; + }; + + mmc1_pins_sleep: pinmux_mmc1_pins_sleep { + pinctrl-single,pins = < + 0x0F0 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x0F4 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x0F8 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x0FC (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x100 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x104 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x1A0 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x160 (PIN_INPUT_PULLDOWN | MUX_MODE7) + >; + }; + + emmc_pins: pinmux_emmc_pins { + pinctrl-single,pins = < + 0x80 (PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_csn1.mmc1_clk */ + 0x84 (PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_csn2.mmc1_cmd */ + 0x00 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad0.mmc1_dat0 */ + 0x04 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad1.mmc1_dat1 */ + 0x08 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad2.mmc1_dat2 */ + 0x0c (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad3.mmc1_dat3 */ + 0x10 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad4.mmc1_dat4 */ + 0x14 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad5.mmc1_dat5 */ + 0x18 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad6.mmc1_dat6 */ + 0x1c (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad7.mmc1_dat7 */ + >; + }; + + ecap0_pins_default: backlight_pins { + pinctrl-single,pins = < + 0x164 0x0 /* eCAP0_in_PWM0_out.eCAP0_in_PWM0_out MODE0 */ + >; + }; + + ecap0_pins_sleep: ecap0_pins_sleep { + pinctrl-single,pins = < + 0x164 (PULL_DISABLE | MUX_MODE7) /* eCAP0_in_PWM0_out.eCAP0_in_PWM0_out */ + >; + }; + dcan0_default: dcan0_default_pins { + pinctrl-single,pins = < + 0x178 0x0a /* uart1_ctsn.dcan0_tx_mux2, OUTPUT | MODE2 */ + 0x17c 0x2a /* uart1_rtsn.dcan0_rx_mux2, INPUT | MODE2 */ + >; + }; + }; + +&tps { + compatible = "ti,tps65217"; + regulators { + #address-cells = <1>; + #size-cells = <0>; + + dcdc1_reg: regulator@0 { + reg = <0>; + regulator-always-on; + }; + + dcdc2_reg: regulator@1 { + reg = <1>; + /* VDD_MPU voltage limits 0.95V - 1.325V with +/-4% tolerance */ + regulator-name = "vdd_mpu"; + regulator-min-microvolt = <925000>; + regulator-max-microvolt = <1378000>; + regulator-boot-on; + regulator-always-on; + }; + + dcdc3_reg: regulator@2 { + reg = <2>; + /* VDD_CORE voltage limits 0.95V - 1.1V with +/-4% tolerance */ + regulator-name = "vdd_core"; + regulator-min-microvolt = <925000>; + regulator-max-microvolt = <1150000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo1_reg: regulator@3 { + reg = <3>; + regulator-always-on; + }; + + ldo2_reg: regulator@4 { + reg = <4>; + regulator-always-on; + }; + + ldo3_reg: regulator@5 { + reg = <5>; + regulator-always-on; + }; + + ldo4_reg: regulator@6 { + reg = <6>; + regulator-always-on; + }; + }; +}; + +&cpsw_emac0 { + phy_id = <&davinci_mdio>, <0>; + phy-mode = "mii"; +}; + +&cpsw_emac1 { + phy_id = <&davinci_mdio>, <1>; + phy-mode = "mii"; +}; + +&mac { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&cpsw_default>; + pinctrl-1 = <&cpsw_sleep>; + slaves = <2>; + dual_emac = <1>; + status = "okay"; +}; + +&davinci_mdio { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&davinci_mdio_default>; + pinctrl-1 = <&davinci_mdio_sleep>; + status = "okay"; +}; + +&mmc1 { + status = "okay"; + bus-width = <0x4>; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&mmc1_pins_default>; + pinctrl-1 = <&mmc1_pins_sleep>; + cd-gpios = <&gpio0 6 GPIO_ACTIVE_HIGH>; + cd-inverted; +}; + +&dcan0 { + pinctrl-names = "default"; + pinctrl-0 = <&dcan0_default>; + status = "okay"; +}; + +&tscadc { + status = "okay"; + tsc { + ti,wires = <4>; + ti,x-plate-resistance = <200>; + ti,coordinate-readouts = <5>; + ti,wire-config = <0x00 0x11 0x22 0x33>; + }; + + adc { + ti,adc-channels = <0 1 2 3>; + }; +}; diff --git a/arch/arm/boot/dts/am33xx.dtsi b/arch/arm/boot/dts/am33xx.dtsi index e8cf17c8f..8dea3ed1e 100644 --- a/arch/arm/boot/dts/am33xx.dtsi +++ b/arch/arm/boot/dts/am33xx.dtsi @@ -35,6 +35,11 @@ phy1 = &usb1_phy; ethernet0 = &cpsw_emac0; ethernet1 = &cpsw_emac1; + mmc0 = &mmc1; + mmc1 = &mmc2; + mmc2 = &mmc3; + spi0 = &spi0; + spi1 = &spi1; }; cpus { @@ -45,19 +50,7 @@ device_type = "cpu"; reg = <0>; - /* - * To consider voltage drop between PMIC and SoC, - * tolerance value is reduced to 2% from 4% and - * voltage value is increased as a precaution. - */ - operating-points = < - /* kHz uV */ - 720000 1285000 - 600000 1225000 - 500000 1125000 - 275000 1125000 - >; - voltage-tolerance = <2>; /* 2 percentage */ + operating-points-v2 = <&cpu0_opp_table>; clocks = <&dpll_mpu_ck>; clock-names = "cpu"; @@ -66,6 +59,80 @@ }; }; + cpu0_opp_table: opp_table0 { + compatible = "operating-points-v2-ti-cpu"; + ti,syscon-efuse = <&scm_conf 0x7fc 0x1fff 0>; + ti,syscon-rev = <&scm_conf 0x600>; + + /* + * The three following nodes are marked with opp-suspend + * because the can not be enabled simultaneously on a + * single SoC. + */ + opp50@300000000 { + opp-hz = /bits/ 64 <300000000>; + opp-microvolt = <950000 931000 969000>; + opp-supported-hw = <0x06 0x0010>; + opp-suspend; + }; + + opp100@275000000 { + opp-hz = /bits/ 64 <275000000>; + opp-microvolt = <1100000 1078000 1122000>; + opp-supported-hw = <0x01 0x00FF>; + opp-suspend; + }; + + opp100@300000000 { + opp-hz = /bits/ 64 <300000000>; + opp-microvolt = <1100000 1078000 1122000>; + opp-supported-hw = <0x06 0x0020>; + opp-suspend; + }; + + opp100@500000000 { + opp-hz = /bits/ 64 <500000000>; + opp-microvolt = <1100000 1078000 1122000>; + opp-supported-hw = <0x01 0xFFFF>; + }; + + opp100@600000000 { + opp-hz = /bits/ 64 <600000000>; + opp-microvolt = <1100000 1078000 1122000>; + opp-supported-hw = <0x06 0x0040>; + }; + + opp120@600000000 { + opp-hz = /bits/ 64 <600000000>; + opp-microvolt = <1200000 1176000 1224000>; + opp-supported-hw = <0x01 0xFFFF>; + }; + + opp120@720000000 { + opp-hz = /bits/ 64 <720000000>; + opp-microvolt = <1200000 1176000 1224000>; + opp-supported-hw = <0x06 0x0080>; + }; + + oppturbo@720000000 { + opp-hz = /bits/ 64 <720000000>; + opp-microvolt = <1260000 1234800 1285200>; + opp-supported-hw = <0x01 0xFFFF>; + }; + + oppturbo@800000000 { + opp-hz = /bits/ 64 <800000000>; + opp-microvolt = <1260000 1234800 1285200>; + opp-supported-hw = <0x06 0x0100>; + }; + + oppnitro@1000000000 { + opp-hz = /bits/ 64 <1000000000>; + opp-microvolt = <1325000 1298500 1351500>; + opp-supported-hw = <0x04 0x0200>; + }; + }; + pmu { compatible = "arm,cortex-a8-pmu"; interrupts = <3>; @@ -90,7 +157,7 @@ * for the moment, just use a fake OCP bus entry to represent * the whole bus hierarchy. */ - ocp { + ocp: ocp { compatible = "simple-bus"; #address-cells = <1>; #size-cells = <1>; @@ -499,12 +566,25 @@ ti,timer-pwm; }; + pruss: pruss@4a300000 { + compatible = "ti,pruss-v2"; + ti,hwmods = "pruss"; + ti,deassert-hard-reset = "pruss", "pruss"; + reg = <0x4a300000 0x080000>; + ti,pintc-offset = <0x20000>; + interrupt-parent = <&intc>; + status = "disabled"; + interrupts = <20 21 22 23 24 25 26 27>; + }; + rtc: rtc@44e3e000 { compatible = "ti,am3352-rtc", "ti,da830-rtc"; reg = <0x44e3e000 0x1000>; interrupts = <75 76>; ti,hwmods = "rtc"; + ti,no-reset-on-init; + ti,no-idle-on-init; }; spi0: spi@48030000 { @@ -690,6 +770,16 @@ status = "disabled"; }; + eqep0: eqep@0x48300180 { + compatible = "ti,am33xx-eqep"; + reg = <0x48300180 0x80>; + clocks = <&l4ls_gclk>; + clock-names = "fck"; + interrupt-parent = <&intc>; + interrupts = <79>; + status = "disabled"; + }; + ehrpwm0: pwm@48300200 { compatible = "ti,am3352-ehrpwm", "ti,am33xx-ehrpwm"; @@ -724,6 +814,17 @@ status = "disabled"; }; + + eqep1: eqep@0x48302180 { + compatible = "ti,am33xx-eqep"; + reg = <0x48302180 0x80>; + clocks = <&l4ls_gclk>; + clock-names = "fck"; + interrupt-parent = <&intc>; + interrupts = <88>; + status = "disabled"; + }; + ehrpwm1: pwm@48302200 { compatible = "ti,am3352-ehrpwm", "ti,am33xx-ehrpwm"; @@ -758,6 +859,16 @@ status = "disabled"; }; + eqep2: eqep@0x48304180 { + compatible = "ti,am33xx-eqep"; + reg = <0x48304180 0x80>; + clocks = <&l4ls_gclk>; + clock-names = "fck"; + interrupt-parent = <&intc>; + interrupts = <89>; + status = "disabled"; + }; + ehrpwm2: pwm@48304200 { compatible = "ti,am3352-ehrpwm", "ti,am33xx-ehrpwm"; diff --git a/arch/arm/boot/dts/am4372.dtsi b/arch/arm/boot/dts/am4372.dtsi index ae7a470aa..45e2e7209 100644 --- a/arch/arm/boot/dts/am4372.dtsi +++ b/arch/arm/boot/dts/am4372.dtsi @@ -49,15 +49,15 @@ clock-names = "cpu"; operating-points-v2 = <&cpu0_opp_table>; - ti,syscon-efuse = <&scm_conf 0x610 0x3f 0>; - ti,syscon-rev = <&scm_conf 0x600>; clock-latency = <300000>; /* From omap-cpufreq driver */ }; }; cpu0_opp_table: opp_table0 { - compatible = "operating-points-v2"; + compatible = "operating-points-v2-ti-cpu"; + ti,syscon-efuse = <&scm_conf 0x610 0x3f 0>; + ti,syscon-rev = <&scm_conf 0x600>; opp50@300000000 { opp-hz = /bits/ 64 <300000000>; diff --git a/arch/arm/boot/dts/am57xx-beagle-x15-common.dtsi b/arch/arm/boot/dts/am57xx-beagle-x15-common.dtsi index 6df7829a2..a2e4c2920 100644 --- a/arch/arm/boot/dts/am57xx-beagle-x15-common.dtsi +++ b/arch/arm/boot/dts/am57xx-beagle-x15-common.dtsi @@ -190,6 +190,11 @@ >; }; }; + +&bb2d { + status = "okay"; +}; + &i2c1 { status = "okay"; clock-frequency = <400000>; diff --git a/arch/arm/boot/dts/dra7.dtsi b/arch/arm/boot/dts/dra7.dtsi index d4fcd68f6..b491d3134 100644 --- a/arch/arm/boot/dts/dra7.dtsi +++ b/arch/arm/boot/dts/dra7.dtsi @@ -80,11 +80,7 @@ compatible = "arm,cortex-a15"; reg = <0>; - operating-points = < - /* kHz uV */ - 1000000 1060000 - 1176000 1160000 - >; + operating-points-v2 = <&cpu0_opp_table>; clocks = <&dpll_mpu_ck>; clock-names = "cpu"; @@ -98,6 +94,25 @@ }; }; + cpu0_opp_table: opp_table0 { + compatible = "operating-points-v2-ti-cpu"; + ti,syscon-efuse = <&scm_wkup 0x20c 0xf80000 19>; + ti,syscon-rev = <&scm_wkup 0x204>; + + opp_nom@1000000000 { + opp-hz = /bits/ 64 <1000000000>; + opp-microvolt = <1060000 850000 1150000>; + opp-supported-hw = <0xFF 0x01>; + opp-suspend; + }; + + opp_od@1176000000 { + opp-hz = /bits/ 64 <1176000000>; + opp-microvolt = <1160000 885000 1160000>; + opp-supported-hw = <0xFF 0x02>; + }; + }; + /* * The soc node represents the soc top level view. It is used for IPs * that are not memory mapped in the MPU view or for the MPU itself. @@ -400,6 +415,13 @@ reg = <0x40d00000 0x100>; }; + dra7_iodelay_core: padconf@4844a000 { + compatible = "ti,dra7-iodelay"; + reg = <0x4844a000 0x0d1c>; + #address-cells = <1>; + #size-cells = <0>; + }; + sdma: dma-controller@4a056000 { compatible = "ti,omap4430-sdma"; reg = <0x4a056000 0x1000>; @@ -958,6 +980,16 @@ ti,hwmods = "dmm"; }; + bb2d: bb2d@59000000 { + compatible = "ti,dra7-bb2d","vivante,gc"; + reg = <0x59000000 0x0700>; + interrupts = ; + ti,hwmods = "bb2d"; + clocks = <&dpll_core_h24x2_ck>; + clock-names = "fclk"; + status = "disabled"; + }; + i2c1: i2c@48070000 { compatible = "ti,omap4-i2c"; reg = <0x48070000 0x100>; @@ -1968,6 +2000,12 @@ }; }; + gpu-subsystem { + compatible = "vivante,gc-gpu-subsystem"; + cores = <&bb2d>; + status = "okay"; + }; + thermal_zones: thermal-zones { #include "omap4-cpu-thermal.dtsi" #include "omap5-gpu-thermal.dtsi" diff --git a/arch/arm/boot/dts/dra74x.dtsi b/arch/arm/boot/dts/dra74x.dtsi index 0a78347e6..24e6746c5 100644 --- a/arch/arm/boot/dts/dra74x.dtsi +++ b/arch/arm/boot/dts/dra74x.dtsi @@ -17,6 +17,7 @@ device_type = "cpu"; compatible = "arm,cortex-a15"; reg = <1>; + operating-points-v2 = <&cpu0_opp_table>; }; }; @@ -79,6 +80,10 @@ }; }; +&cpu0_opp_table { + opp-shared; +}; + &dss { reg = <0x58000000 0x80>, <0x58004054 0x4>, diff --git b/arch/arm/boot/dts/exynos5422-artik10-eval.dts b/arch/arm/boot/dts/exynos5422-artik10-eval.dts new file mode 100644 index 000000000..100125570 --- /dev/null +++ b/arch/arm/boot/dts/exynos5422-artik10-eval.dts @@ -0,0 +1,278 @@ +/* + * SAMSUNG ARTIK10 board device tree source + * + * Copyright (c) 2015 Samsung Electronics Co., Ltd. + * http://www.samsung.com + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +/dts-v1/; + +#include +#include +#include +#include +#include "exynos5800.dtsi" +#include "exynos5422-cpus.dtsi" +#include "exynos-mfc-reserved-memory.dtsi" + +/ { + model = "Samsung ARTIK10 board based on EXYNOS5422"; + compatible = "samsung,artik10", "samsung,exynos5422", "samsung,exynos5"; + + memory@40000000 { + device_type = "memory"; + reg = <0x40000000 0x7EA00000>; + }; + + chosen { + stdout-path = "serial2:115200n8"; + }; + + firmware@02073000 { + compatible = "samsung,secure-firmware"; + reg = <0x02073000 0x1000>; + }; + + fixed-rate-clocks { + oscclk { + compatible = "samsung,exynos5420-oscclk"; + clock-frequency = <24000000>; + }; + }; + + rtc { + status = "okay"; + }; +}; + +&cpu0 { + cpu-supply = <&buck6_reg>; +}; + +&cpu4 { + cpu-supply = <&buck2_reg>; +}; + +&pinctrl_0 { + s2mps11_irq: s2mps11-irq { + samsung,pins = "gpx3-2"; + samsung,pin-pud = <3>; + samsung,pin-drv = <3>; + }; +}; + +&hsi2c_4 { + clock-frequency = <400000>; + status = "okay"; + + s2mps11_pmic@66 { + compatible = "samsung,s2mps11-pmic"; + interrupt-parent = <&gpx3>; + interrupts = <2 IRQ_TYPE_EDGE_FALLING>; + reg = <0x66>; + + + pinctrl-names = "default"; + pinctrl-0 = <&s2mps11_irq>; + + s2mps11_osc: clocks { + #clock-cells = <1>; + clock-output-names = "s2mps11_ap", + "s2mps11_cp", "s2mps11_bt"; + }; + + regulators { + ldo4_reg: LDO4 { + regulator-name = "vdd_adc"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + + ldo6_reg: LDO6 { + regulator-name = "vdd_ldo6"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-always-on; + }; + + ldo7_reg: LDO7 { + regulator-name = "vdd_ldo7"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + + ldo13_reg: LDO13 { + regulator-name = "vqmmc"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + }; + + ldo17_reg: LDO17 { + regulator-name = "vdd_ldo17"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + }; + + ldo18_reg: LDO18 { + regulator-name = "vdd_ldo18"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + + ldo19_reg: LDO19 { + regulator-name = "vmmc"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + + ldo20_reg: LDO20 { + regulator-name = "vdd_ldo20"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + + ldo23_reg: LDO23 { + regulator-name = "vdd_mifs"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1100000>; + regulator-always-on; + }; + + ldo24_reg: LDO24 { + regulator-name = "vdd_ldo24"; + regulator-min-microvolt = <2400000>; + regulator-max-microvolt = <2400000>; + }; + + ldo25_reg: LDO25 { + regulator-name = "vdd_ldo25"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + ldo27_reg: LDO27 { + regulator-name = "vdd_g3ds"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1100000>; + regulator-always-on; + }; + + ldo28_reg: LDO28 { + regulator-name = "vdd_ldo28"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + }; + + ldo32_reg: LDO32 { + regulator-name = "vdd_lcd_1v8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + ldo38_reg: LDO38 { + regulator-name = "vdd_ldo38"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-always-on; + }; + + buck1_reg: BUCK1 { + regulator-name = "vdd_mif"; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1300000>; + regulator-always-on; + }; + + buck2_reg: BUCK2 { + regulator-name = "vdd_eagle"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1500000>; + regulator-always-on; + }; + + buck3_reg: BUCK3 { + regulator-name = "vdd_int"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1400000>; + regulator-always-on; + }; + + buck4_reg: BUCK4 { + regulator-name = "vdd_g3d"; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1400000>; + regulator-always-on; + }; + + buck6_reg: BUCK6 { + regulator-name = "vdd_kfc"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1500000>; + regulator-always-on; + }; + + buck10_reg: BUCK10 { + regulator-name = "vdd_cam_isp_1.0v"; + regulator-min-microvolt = <750000>; + regulator-max-microvolt = <1500000>; + regulator-always-on; + }; + }; + }; +}; + +&mmc_0 { + status = "okay"; + broken-cd; + card-detect-delay = <200>; + samsung,dw-mshc-ciu-div = <3>; + samsung,dw-mshc-sdr-timing = <0 4>; + samsung,dw-mshc-ddr-timing = <0 2>; + samsung,dw-mshc-hs400-timing = <0 2>; + samsung,read-strobe-delay = <90>; + pinctrl-names = "default"; + pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus1 &sd0_bus4 &sd0_bus8 + &sd0_rclk>; + bus-width = <8>; + cap-mmc-highspeed; + keep-power-in-suspend; + non-removable; +}; + +&mmc_2 { + status = "okay"; + card-detect-delay = <200>; + samsung,dw-mshc-ciu-div = <3>; + samsung,dw-mshc-sdr-timing = <2 3>; + samsung,dw-mshc-ddr-timing = <1 2>; + pinctrl-names = "default"; + pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus1 &sd2_bus4>; + bus-width = <4>; + cap-sd-highspeed; + vmmc-supply = <&ldo28_reg>; +}; + +&nocp_mem0_0 { + status = "okay"; +}; + +&nocp_mem0_1 { + status = "okay"; +}; + +&nocp_mem1_0 { + status = "okay"; +}; + +&nocp_mem1_1 { + status = "okay"; +}; diff --git b/arch/arm/boot/dts/imx6q-ccimx6sbc.dts b/arch/arm/boot/dts/imx6q-ccimx6sbc.dts new file mode 100644 index 000000000..d2492406e --- /dev/null +++ b/arch/arm/boot/dts/imx6q-ccimx6sbc.dts @@ -0,0 +1,303 @@ +/* + * Copyright (C) 2015 Robert Nelson (robertcnelson@gmail.com) + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License. + * + * This file is distributed in the hope that it will be useful + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ +/dts-v1/; + +#include "imx6q.dtsi" +#include + +/ { + model = "Digi ConnectCore-i.MX6 SBC Board"; + compatible = "digi,connectcore/q", "fsl,imx6q"; + + chosen { + stdout-path = &uart4; + }; + + memory { + reg = <0x10000000 0x40000000>; + }; + + regulators { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; + + reg_usbh1_reset: regulator@1 { + compatible = "regulator-fixed"; + reg = <1>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usbh1>; + regulator-name = "usbh1_reset"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&gpio3 10 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + reg_usb_otg_vbus: regulator@2 { + compatible = "regulator-fixed"; + reg = <2>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usbotg>; + regulator-name = "usb_otg_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + }; +}; + +&fec { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_enet>; + phy-mode = "rgmii"; + phy-reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>; + status = "okay"; +}; + +&hdmi { + ddc-i2c-bus = <&i2c3>; + status = "okay"; +}; + +&i2c2 { + clock-frequency = <400000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c2>; + status = "okay"; + + pmic@58 { + compatible = "dlg,da9063"; + reg = <0x58>; + interrupt-parent = <&gpio1>; + interrupts = <17 0x8>; /* active-low GPIO0_17 */ + + regulators { + vdd_3v3_reg: bperi { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + ldo3_reg: ldo3 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + ldo4_reg: ldo4 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + ldo6_reg: ldo6 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + ldo7_reg: ldo7 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + + ldo8_reg: ldo8 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + }; + }; +}; + +&i2c3 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c3>; + status = "okay"; +}; + +&iomuxc { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_hog>; + + imx6qdl-ccimx6sbc { + pinctrl_hog: hoggrp { + fsl,pins = < + /* da9063*/ + MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x80000000 + >; + }; + + pinctrl_enet: enetgrp { + fsl,pins = < + MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x100b0 + MX6QDL_PAD_ENET_MDC__ENET_MDC 0x100b0 + MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x100b0 + MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x100b0 + MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x100b0 + MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x100b0 + MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x100b0 + MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x100b0 + MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x100b0 + MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b0b0 + MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b0b0 + MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b0b0 + MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b0b0 + MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b0b0 + MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b0b0 + /* Phy reset */ + MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25 0x000b0 + >; + }; + + pinctrl_i2c2: i2c2grp { + fsl,pins = < + MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1 + MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1 + >; + }; + + pinctrl_i2c3: i2c3grp { + fsl,pins = < + MX6QDL_PAD_GPIO_5__I2C3_SCL 0x4001b8b1 + MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b8b1 + >; + }; + + pinctrl_uart4: uart4grp { + fsl,pins = < + MX6QDL_PAD_KEY_COL0__UART4_TX_DATA 0x1b0b1 + MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA 0x1b0b1 + >; + }; + + pinctrl_usbh1: usbh1grp { + fsl,pins = < + /* need to force low for hub reset */ + MX6QDL_PAD_EIM_DA10__GPIO3_IO10 0x10b0 + >; + }; + + pinctrl_usbotg: usbotggrp { + fsl,pins = < + MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x17059 + MX6QDL_PAD_EIM_D21__USB_OTG_OC 0x1b0b0 + /* power enable, high active */ + MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x10b0 + >; + }; + + pinctrl_usdhc2: usdhc2grp { + fsl,pins = < + MX6QDL_PAD_SD2_CMD__SD2_CMD 0x17059 + MX6QDL_PAD_SD2_CLK__SD2_CLK 0x10059 + MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x17059 + MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x17059 + MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x17059 + MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x17059 + >; + }; + + pinctrl_usdhc4: usdhc4grp { + fsl,pins = < + MX6QDL_PAD_SD4_CMD__SD4_CMD 0x17059 + MX6QDL_PAD_SD4_CLK__SD4_CLK 0x10059 + MX6QDL_PAD_SD4_DAT0__SD4_DATA0 0x17059 + MX6QDL_PAD_SD4_DAT1__SD4_DATA1 0x17059 + MX6QDL_PAD_SD4_DAT2__SD4_DATA2 0x17059 + MX6QDL_PAD_SD4_DAT3__SD4_DATA3 0x17059 + MX6QDL_PAD_SD4_DAT4__SD4_DATA4 0x17059 + MX6QDL_PAD_SD4_DAT5__SD4_DATA5 0x17059 + MX6QDL_PAD_SD4_DAT6__SD4_DATA6 0x17059 + MX6QDL_PAD_SD4_DAT7__SD4_DATA7 0x17059 + >; + }; + }; +}; + +&sata { + status = "okay"; +}; + +&ssi1 { + status = "okay"; +}; + +&uart4 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart4>; + status = "okay"; +}; + +&usbh1 { + vbus-supply = <®_usbh1_reset>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usbh1>; + status = "okay"; +}; + +&usbotg { + vbus-supply = <®_usb_otg_vbus>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usbotg>; + status = "okay"; +}; + +&usdhc2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc2>; + bus-width = <4>; + broken-cd; /* cd & wp, is not wired up on this board */ + status = "okay"; +}; + +&usdhc4 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc4>; + bus-width = <8>; + non-removable; + status = "okay"; +}; diff --git a/arch/arm/boot/dts/imx6q-evi.dts b/arch/arm/boot/dts/imx6q-evi.dts index 6de21ff47..3277a0655 100644 --- a/arch/arm/boot/dts/imx6q-evi.dts +++ b/arch/arm/boot/dts/imx6q-evi.dts @@ -54,18 +54,6 @@ reg = <0x10000000 0x40000000>; }; - reg_usbh1_vbus: regulator-usbhubreset { - compatible = "regulator-fixed"; - regulator-name = "usbh1_vbus"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - enable-active-high; - startup-delay-us = <2>; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_usbh1_hubreset>; - gpio = <&gpio7 12 GPIO_ACTIVE_HIGH>; - }; - reg_usb_otg_vbus: regulator-usbotgvbus { compatible = "regulator-fixed"; regulator-name = "usb_otg_vbus"; @@ -207,12 +195,18 @@ }; &usbh1 { - vbus-supply = <®_usbh1_vbus>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_usbh1>; dr_mode = "host"; disable-over-current; status = "okay"; + + usb2415host: hub@1 { + compatible = "usb424,2513"; + reg = <1>; + reset-gpios = <&gpio7 12 GPIO_ACTIVE_LOW>; + reset-duration-us = <3000>; + }; }; &usbotg { @@ -471,11 +465,6 @@ MX6QDL_PAD_GPIO_3__USB_H1_OC 0x1b0b0 /* usbh1_b OC */ MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x1b0b0 - >; - }; - - pinctrl_usbh1_hubreset: usbh1hubresetgrp { - fsl,pins = < MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x1b0b0 >; }; diff --git a/arch/arm/boot/dts/imx6qdl-udoo.dtsi b/arch/arm/boot/dts/imx6qdl-udoo.dtsi index c96c91d83..a173de20e 100644 --- a/arch/arm/boot/dts/imx6qdl-udoo.dtsi +++ b/arch/arm/boot/dts/imx6qdl-udoo.dtsi @@ -9,6 +9,8 @@ * */ +#include + / { aliases { backlight = &backlight; @@ -58,17 +60,6 @@ #address-cells = <1>; #size-cells = <0>; - reg_usb_h1_vbus: regulator@0 { - compatible = "regulator-fixed"; - reg = <0>; - regulator-name = "usb_h1_vbus"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - enable-active-high; - startup-delay-us = <2>; /* USB2415 requires a POR of 1 us minimum */ - gpio = <&gpio7 12 0>; - }; - reg_panel: regulator@1 { compatible = "regulator-fixed"; reg = <1>; @@ -188,7 +179,7 @@ pinctrl_usbh: usbhgrp { fsl,pins = < - MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x80000000 + MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x1b0b0 MX6QDL_PAD_NANDF_CS2__CCM_CLKO2 0x130b0 >; }; @@ -259,9 +250,16 @@ &usbh1 { pinctrl-names = "default"; pinctrl-0 = <&pinctrl_usbh>; - vbus-supply = <®_usb_h1_vbus>; - clocks = <&clks IMX6QDL_CLK_CKO>; status = "okay"; + + usb2415: hub@1 { + compatible = "usb424,2514"; + reg = <1>; + + clocks = <&clks IMX6QDL_CLK_CKO>; + reset-gpios = <&gpio7 12 GPIO_ACTIVE_LOW>; + reset-duration-us = <3000>; + }; }; &usdhc3 { diff --git a/arch/arm/boot/dts/imx6qdl-wandboard-revb1.dtsi b/arch/arm/boot/dts/imx6qdl-wandboard-revb1.dtsi index ef7fa62b9..b5d0f58ab 100644 --- a/arch/arm/boot/dts/imx6qdl-wandboard-revb1.dtsi +++ b/arch/arm/boot/dts/imx6qdl-wandboard-revb1.dtsi @@ -11,6 +11,24 @@ #include "imx6qdl-wandboard.dtsi" +/ { + rfkill { + compatible = "wand,imx6qdl-wandboard-rfkill"; + pinctrl-names = "default"; + pinctrl-0 = <>; + + bluetooth-on = <&gpio3 13 0>; + bluetooth-wake = <&gpio3 14 0>; + bluetooth-host-wake = <&gpio3 15 0>; + + wifi-ref-on = <&gpio2 29 0>; + wifi-rst-n = <&gpio5 2 0>; + wifi-reg-on = <&gpio1 26 0>; + wifi-host-wake = <&gpio1 29 0>; + wifi-wake = <&gpio1 30 0>; + }; +}; + &iomuxc { pinctrl-0 = <&pinctrl_hog>; @@ -37,6 +55,5 @@ &usdhc2 { pinctrl-names = "default"; pinctrl-0 = <&pinctrl_usdhc2>; - non-removable; status = "okay"; }; diff --git a/arch/arm/boot/dts/imx6qdl-wandboard-revc1.dtsi b/arch/arm/boot/dts/imx6qdl-wandboard-revc1.dtsi index 8d893a78c..b2097ef98 100644 --- a/arch/arm/boot/dts/imx6qdl-wandboard-revc1.dtsi +++ b/arch/arm/boot/dts/imx6qdl-wandboard-revc1.dtsi @@ -11,6 +11,24 @@ #include "imx6qdl-wandboard.dtsi" +/ { + rfkill { + compatible = "wand,imx6qdl-wandboard-rfkill"; + pinctrl-names = "default"; + pinctrl-0 = <>; + + bluetooth-on = <&gpio5 21 0>; + bluetooth-wake = <&gpio5 30 0>; + bluetooth-host-wake = <&gpio5 20 0>; + + wifi-ref-on = <&gpio5 31 0>; /* Wifi Power Enable */ + wifi-rst-n = <&gpio6 0 0>; /* WIFI_ON reset */ + wifi-reg-on = <&gpio1 26 0>; /* WL_REG_ON */ + wifi-host-wake = <&gpio1 29 0>; /* WL_HOST_WAKE */ + wifi-wake = <&gpio1 30 0>; /* WL_WAKE */ + }; +}; + &iomuxc { pinctrl-0 = <&pinctrl_hog>; diff --git a/arch/arm/boot/dts/imx6qdl.dtsi b/arch/arm/boot/dts/imx6qdl.dtsi index be2e7475e..b946245ee 100644 --- a/arch/arm/boot/dts/imx6qdl.dtsi +++ b/arch/arm/boot/dts/imx6qdl.dtsi @@ -935,6 +935,8 @@ usbh1: usb@02184200 { compatible = "fsl,imx6q-usb", "fsl,imx27-usb"; + #address-cells = <1>; + #size-cells = <0>; reg = <0x02184200 0x200>; interrupts = <0 40 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks IMX6QDL_CLK_USBOH3>; @@ -949,6 +951,8 @@ usbh2: usb@02184400 { compatible = "fsl,imx6q-usb", "fsl,imx27-usb"; + #address-cells = <1>; + #size-cells = <0>; reg = <0x02184400 0x200>; interrupts = <0 41 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks IMX6QDL_CLK_USBOH3>; @@ -962,6 +966,8 @@ usbh3: usb@02184600 { compatible = "fsl,imx6q-usb", "fsl,imx27-usb"; + #address-cells = <1>; + #size-cells = <0>; reg = <0x02184600 0x200>; interrupts = <0 42 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks IMX6QDL_CLK_USBOH3>; diff --git b/arch/arm/boot/dts/imx6ul-14x14-evk-ism43362-b81-evb.dts b/arch/arm/boot/dts/imx6ul-14x14-evk-ism43362-b81-evb.dts new file mode 100644 index 000000000..9ba86b87e --- /dev/null +++ b/arch/arm/boot/dts/imx6ul-14x14-evk-ism43362-b81-evb.dts @@ -0,0 +1,516 @@ +/* + * Copyright (C) 2015 Freescale Semiconductor, Inc. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +/dts-v1/; + +#include "imx6ul.dtsi" + +/ { + model = "Freescale i.MX6 UltraLite 14x14 EVK Board"; + compatible = "fsl,imx6ul-14x14-evk", "fsl,imx6ul"; + + chosen { + stdout-path = &uart1; + }; + + memory { + reg = <0x80000000 0x20000000>; + }; + + backlight { + compatible = "pwm-backlight"; + pwms = <&pwm1 0 5000000>; + brightness-levels = <0 4 8 16 32 64 128 255>; + default-brightness-level = <6>; + status = "okay"; + }; + + regulators { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; + + reg_sd1_vmmc: sd1_regulator { + compatible = "regulator-fixed"; + regulator-name = "VSD_3V3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio1 9 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + wlreg_on: fixedregulator@100 { + compatible = "regulator-fixed"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-name = "wlreg_on"; + gpio = <&gpio5 1 GPIO_ACTIVE_HIGH>; + startup-delay-us = <100>; + enable-active-high; + }; + }; + + sound { + compatible = "simple-audio-card"; + simple-audio-card,name = "mx6ul-wm8960"; + simple-audio-card,format = "i2s"; + simple-audio-card,bitclock-master = <&dailink_master>; + simple-audio-card,frame-master = <&dailink_master>; + simple-audio-card,widgets = + "Microphone", "Mic Jack", + "Line", "Line In", + "Line", "Line Out", + "Speaker", "Speaker", + "Headphone", "Headphone Jack"; + simple-audio-card,routing = + "Headphone Jack", "HP_L", + "Headphone Jack", "HP_R", + "Speaker", "SPK_LP", + "Speaker", "SPK_LN", + "Speaker", "SPK_RP", + "Speaker", "SPK_RN", + "LINPUT1", "Mic Jack", + "LINPUT3", "Mic Jack", + "RINPUT1", "Mic Jack", + "RINPUT2", "Mic Jack"; + + simple-audio-card,cpu { + sound-dai = <&sai2>; + }; + + dailink_master: simple-audio-card,codec { + sound-dai = <&codec>; + clocks = <&clks IMX6UL_CLK_SAI2>; + }; + }; +}; + +&clks { + assigned-clocks = <&clks IMX6UL_CLK_PLL4_AUDIO_DIV>; + assigned-clock-rates = <786432000>; +}; + +&cpu0 { + arm-supply = <®_arm>; + soc-supply = <®_soc>; +}; + +&i2c2 { + clock_frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c2>; + status = "okay"; + + codec: wm8960@1a { + #sound-dai-cells = <0>; + compatible = "wlf,wm8960"; + reg = <0x1a>; + wlf,shared-lrclk; + }; +}; + +&fec1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_enet1>; + phy-mode = "rmii"; + phy-handle = <ðphy0>; + status = "okay"; +}; + +&fec2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_enet2>; + phy-mode = "rmii"; + phy-handle = <ðphy1>; + status = "okay"; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + ethphy0: ethernet-phy@2 { + reg = <2>; + }; + + ethphy1: ethernet-phy@1 { + reg = <1>; + }; + }; +}; + + +&lcdif { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_lcdif_dat + &pinctrl_lcdif_ctrl>; + display = <&display0>; + status = "okay"; + + display0: display { + bits-per-pixel = <16>; + bus-width = <24>; + + display-timings { + native-mode = <&timing0>; + + timing0: timing0 { + clock-frequency = <9200000>; + hactive = <480>; + vactive = <272>; + hfront-porch = <8>; + hback-porch = <4>; + hsync-len = <41>; + vback-porch = <2>; + vfront-porch = <4>; + vsync-len = <10>; + hsync-active = <0>; + vsync-active = <0>; + de-active = <1>; + pixelclk-active = <0>; + }; + }; + }; +}; + +&pwm1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm1>; + status = "okay"; +}; + +&qspi { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_qspi>; + status = "okay"; + + flash0: n25q256a@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "micron,n25q256a"; + spi-max-frequency = <29000000>; + reg = <0>; + }; +}; + +&sai2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_sai2>; + assigned-clocks = <&clks IMX6UL_CLK_SAI2_SEL>, + <&clks IMX6UL_CLK_SAI2>; + assigned-clock-parents = <&clks IMX6UL_CLK_PLL4_AUDIO_DIV>; + assigned-clock-rates = <0>, <12288000>; + fsl,sai-mclk-direction-output; + status = "okay"; +}; + +&snvs_poweroff { + status = "okay"; +}; + +&tsc { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_tsc>; + xnur-gpio = <&gpio1 3 GPIO_ACTIVE_LOW>; + measure-delay-time = <0xffff>; + pre-charge-time = <0xfff>; + status = "okay"; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart1>; + status = "okay"; +}; + +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart2>; + uart-has-rtscts; + status = "okay"; +}; + +&usbotg1 { + dr_mode = "peripheral"; + status = "okay"; +}; + +&usbotg2 { + dr_mode = "host"; + disable-over-current; + status = "okay"; +}; + +®_sd1_vmmc { + regulator-always-on; +}; + +&usdhc1 { + pinctrl-names = "default", "state_100mhz", "state_200mhz"; + pinctrl-0 = <&pinctrl_usdhc1>; + pinctrl-1 = <&pinctrl_usdhc1_100mhz>; + pinctrl-2 = <&pinctrl_usdhc1_200mhz>; + cd-gpios = <&gpio1 19 GPIO_ACTIVE_LOW>; + no-1-8-v; + keep-power-in-suspend; + wakeup-source; + vmmc-supply = <®_sd1_vmmc>; + status = "okay"; +}; + +&usdhc2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc2>; + no-1-8-v; + keep-power-in-suspend; + wakeup-source; + status = "okay"; +}; + +&wdog1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_wdog>; + fsl,ext-reset-output; +}; + +&iomuxc { + pinctrl-names = "default"; + + pinctrl_csi1: csi1grp { + fsl,pins = < + MX6UL_PAD_CSI_MCLK__CSI_MCLK 0x1b088 + MX6UL_PAD_CSI_PIXCLK__CSI_PIXCLK 0x1b088 + MX6UL_PAD_CSI_VSYNC__CSI_VSYNC 0x1b088 + MX6UL_PAD_CSI_HSYNC__CSI_HSYNC 0x1b088 + MX6UL_PAD_CSI_DATA00__CSI_DATA02 0x1b088 + MX6UL_PAD_CSI_DATA01__CSI_DATA03 0x1b088 + MX6UL_PAD_CSI_DATA02__CSI_DATA04 0x1b088 + MX6UL_PAD_CSI_DATA03__CSI_DATA05 0x1b088 + MX6UL_PAD_CSI_DATA04__CSI_DATA06 0x1b088 + MX6UL_PAD_CSI_DATA05__CSI_DATA07 0x1b088 + MX6UL_PAD_CSI_DATA06__CSI_DATA08 0x1b088 + MX6UL_PAD_CSI_DATA07__CSI_DATA09 0x1b088 + >; + }; + + pinctrl_enet1: enet1grp { + fsl,pins = < + MX6UL_PAD_ENET1_RX_EN__ENET1_RX_EN 0x1b0b0 + MX6UL_PAD_ENET1_RX_ER__ENET1_RX_ER 0x1b0b0 + MX6UL_PAD_ENET1_RX_DATA0__ENET1_RDATA00 0x1b0b0 + MX6UL_PAD_ENET1_RX_DATA1__ENET1_RDATA01 0x1b0b0 + MX6UL_PAD_ENET1_TX_EN__ENET1_TX_EN 0x1b0b0 + MX6UL_PAD_ENET1_TX_DATA0__ENET1_TDATA00 0x1b0b0 + MX6UL_PAD_ENET1_TX_DATA1__ENET1_TDATA01 0x1b0b0 + MX6UL_PAD_ENET1_TX_CLK__ENET1_REF_CLK1 0x4001b031 + >; + }; + + pinctrl_enet2: enet2grp { + fsl,pins = < + MX6UL_PAD_GPIO1_IO07__ENET2_MDC 0x1b0b0 + MX6UL_PAD_GPIO1_IO06__ENET2_MDIO 0x1b0b0 + MX6UL_PAD_ENET2_RX_EN__ENET2_RX_EN 0x1b0b0 + MX6UL_PAD_ENET2_RX_ER__ENET2_RX_ER 0x1b0b0 + MX6UL_PAD_ENET2_RX_DATA0__ENET2_RDATA00 0x1b0b0 + MX6UL_PAD_ENET2_RX_DATA1__ENET2_RDATA01 0x1b0b0 + MX6UL_PAD_ENET2_TX_EN__ENET2_TX_EN 0x1b0b0 + MX6UL_PAD_ENET2_TX_DATA0__ENET2_TDATA00 0x1b0b0 + MX6UL_PAD_ENET2_TX_DATA1__ENET2_TDATA01 0x1b0b0 + MX6UL_PAD_ENET2_TX_CLK__ENET2_REF_CLK2 0x4001b031 + MX6UL_PAD_SNVS_TAMPER0__GPIO5_IO00 0x17059 + >; + }; + + pinctrl_flexcan1: flexcan1grp{ + fsl,pins = < + MX6UL_PAD_UART3_RTS_B__FLEXCAN1_RX 0x1b020 + MX6UL_PAD_UART3_CTS_B__FLEXCAN1_TX 0x1b020 + >; + }; + + pinctrl_flexcan2: flexcan2grp{ + fsl,pins = < + MX6UL_PAD_UART2_RTS_B__FLEXCAN2_RX 0x1b020 + MX6UL_PAD_UART2_CTS_B__FLEXCAN2_TX 0x1b020 + >; + }; + + pinctrl_i2c1: i2c1grp { + fsl,pins = < + MX6UL_PAD_UART4_TX_DATA__I2C1_SCL 0x4001b8b0 + MX6UL_PAD_UART4_RX_DATA__I2C1_SDA 0x4001b8b0 + >; + }; + + pinctrl_i2c2: i2c2grp { + fsl,pins = < + MX6UL_PAD_UART5_TX_DATA__I2C2_SCL 0x4001b8b0 + MX6UL_PAD_UART5_RX_DATA__I2C2_SDA 0x4001b8b0 + >; + }; + + pinctrl_lcdif_dat: lcdifdatgrp { + fsl,pins = < + MX6UL_PAD_LCD_DATA00__LCDIF_DATA00 0x79 + MX6UL_PAD_LCD_DATA01__LCDIF_DATA01 0x79 + MX6UL_PAD_LCD_DATA02__LCDIF_DATA02 0x79 + MX6UL_PAD_LCD_DATA03__LCDIF_DATA03 0x79 + MX6UL_PAD_LCD_DATA04__LCDIF_DATA04 0x79 + MX6UL_PAD_LCD_DATA05__LCDIF_DATA05 0x79 + MX6UL_PAD_LCD_DATA06__LCDIF_DATA06 0x79 + MX6UL_PAD_LCD_DATA07__LCDIF_DATA07 0x79 + MX6UL_PAD_LCD_DATA08__LCDIF_DATA08 0x79 + MX6UL_PAD_LCD_DATA09__LCDIF_DATA09 0x79 + MX6UL_PAD_LCD_DATA10__LCDIF_DATA10 0x79 + MX6UL_PAD_LCD_DATA11__LCDIF_DATA11 0x79 + MX6UL_PAD_LCD_DATA12__LCDIF_DATA12 0x79 + MX6UL_PAD_LCD_DATA13__LCDIF_DATA13 0x79 + MX6UL_PAD_LCD_DATA14__LCDIF_DATA14 0x79 + MX6UL_PAD_LCD_DATA15__LCDIF_DATA15 0x79 + MX6UL_PAD_LCD_DATA16__LCDIF_DATA16 0x79 + MX6UL_PAD_LCD_DATA17__LCDIF_DATA17 0x79 + MX6UL_PAD_LCD_DATA18__LCDIF_DATA18 0x79 + MX6UL_PAD_LCD_DATA19__LCDIF_DATA19 0x79 + MX6UL_PAD_LCD_DATA20__LCDIF_DATA20 0x79 + MX6UL_PAD_LCD_DATA21__LCDIF_DATA21 0x79 + MX6UL_PAD_LCD_DATA22__LCDIF_DATA22 0x79 + MX6UL_PAD_LCD_DATA23__LCDIF_DATA23 0x79 + >; + }; + + pinctrl_lcdif_ctrl: lcdifctrlgrp { + fsl,pins = < + MX6UL_PAD_LCD_CLK__LCDIF_CLK 0x79 + MX6UL_PAD_LCD_ENABLE__LCDIF_ENABLE 0x79 + MX6UL_PAD_LCD_HSYNC__LCDIF_HSYNC 0x79 + MX6UL_PAD_LCD_VSYNC__LCDIF_VSYNC 0x79 + /* used for lcd reset */ + MX6UL_PAD_SNVS_TAMPER9__GPIO5_IO09 0x79 + >; + }; + + pinctrl_qspi: qspigrp { + fsl,pins = < + MX6UL_PAD_NAND_WP_B__QSPI_A_SCLK 0x70a1 + MX6UL_PAD_NAND_READY_B__QSPI_A_DATA00 0x70a1 + MX6UL_PAD_NAND_CE0_B__QSPI_A_DATA01 0x70a1 + MX6UL_PAD_NAND_CE1_B__QSPI_A_DATA02 0x70a1 + MX6UL_PAD_NAND_CLE__QSPI_A_DATA03 0x70a1 + MX6UL_PAD_NAND_DQS__QSPI_A_SS0_B 0x70a1 + >; + }; + + pinctrl_sai2: sai2grp { + fsl,pins = < + MX6UL_PAD_JTAG_TDI__SAI2_TX_BCLK 0x17088 + MX6UL_PAD_JTAG_TDO__SAI2_TX_SYNC 0x17088 + MX6UL_PAD_JTAG_TRST_B__SAI2_TX_DATA 0x11088 + MX6UL_PAD_JTAG_TCK__SAI2_RX_DATA 0x11088 + MX6UL_PAD_JTAG_TMS__SAI2_MCLK 0x17088 + MX6UL_PAD_SNVS_TAMPER4__GPIO5_IO04 0x17059 + >; + }; + + pinctrl_pwm1: pwm1grp { + fsl,pins = < + MX6UL_PAD_GPIO1_IO08__PWM1_OUT 0x110b0 + >; + }; + + pinctrl_sim2: sim2grp { + fsl,pins = < + MX6UL_PAD_CSI_DATA03__SIM2_PORT1_PD 0xb808 + MX6UL_PAD_CSI_DATA04__SIM2_PORT1_CLK 0x31 + MX6UL_PAD_CSI_DATA05__SIM2_PORT1_RST_B 0xb808 + MX6UL_PAD_CSI_DATA06__SIM2_PORT1_SVEN 0xb808 + MX6UL_PAD_CSI_DATA07__SIM2_PORT1_TRXD 0xb809 + MX6UL_PAD_CSI_DATA02__GPIO4_IO23 0x3008 + >; + }; + + pinctrl_tsc: tscgrp { + fsl,pins = < + MX6UL_PAD_GPIO1_IO01__GPIO1_IO01 0xb0 + MX6UL_PAD_GPIO1_IO02__GPIO1_IO02 0xb0 + MX6UL_PAD_GPIO1_IO03__GPIO1_IO03 0xb0 + MX6UL_PAD_GPIO1_IO04__GPIO1_IO04 0xb0 + >; + }; + + pinctrl_uart1: uart1grp { + fsl,pins = < + MX6UL_PAD_UART1_TX_DATA__UART1_DCE_TX 0x1b0b1 + MX6UL_PAD_UART1_RX_DATA__UART1_DCE_RX 0x1b0b1 + >; + }; + + pinctrl_uart2: uart2grp { + fsl,pins = < + MX6UL_PAD_UART2_TX_DATA__UART2_DCE_TX 0x1b0b1 + MX6UL_PAD_UART2_RX_DATA__UART2_DCE_RX 0x1b0b1 + MX6UL_PAD_UART3_RX_DATA__UART2_DCE_RTS 0x1b0b1 + MX6UL_PAD_UART3_TX_DATA__UART2_DCE_CTS 0x1b0b1 + >; + }; + + pinctrl_usdhc1: usdhc1grp { + fsl,pins = < + MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x17059 + MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x10071 + MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x17059 + MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x17059 + MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x17059 + MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x17059 + MX6UL_PAD_UART1_RTS_B__GPIO1_IO19 0x17059 /* SD1 CD */ + MX6UL_PAD_GPIO1_IO05__USDHC1_VSELECT 0x17059 /* SD1 VSELECT */ + MX6UL_PAD_GPIO1_IO09__GPIO1_IO09 0x17059 /* SD1 RESET */ + MX6UL_PAD_SNVS_TAMPER1__GPIO5_IO01 0x3029 + >; + }; + + pinctrl_usdhc1_100mhz: usdhc1grp100mhz { + fsl,pins = < + MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x170b9 + MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x100b9 + MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x170b9 + MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x170b9 + MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x170b9 + MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x170b9 + MX6UL_PAD_SNVS_TAMPER1__GPIO5_IO01 0x3029 + >; + }; + + pinctrl_usdhc1_200mhz: usdhc1grp200mhz { + fsl,pins = < + MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x170f9 + MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x100f9 + MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x170f9 + MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x170f9 + MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x170f9 + MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x170f9 + MX6UL_PAD_SNVS_TAMPER1__GPIO5_IO01 0x3029 + >; + }; + + pinctrl_usdhc2: usdhc2grp { + fsl,pins = < + MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x17059 + MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x17059 + MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x17059 + MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x17059 + MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x17059 + MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x17059 + >; + }; + + pinctrl_wdog: wdoggrp { + fsl,pins = < + MX6UL_PAD_LCD_RESET__WDOG1_WDOG_ANY 0x30b0 + >; + }; +}; diff --git a/arch/arm/boot/dts/omap3-beagle-xm.dts b/arch/arm/boot/dts/omap3-beagle-xm.dts index 85e297ed0..226b833cc 100644 --- a/arch/arm/boot/dts/omap3-beagle-xm.dts +++ b/arch/arm/boot/dts/omap3-beagle-xm.dts @@ -27,6 +27,7 @@ aliases { display0 = &dvi0; display1 = &tv0; + ethernet = ðernet; }; leds { @@ -146,6 +147,7 @@ }; etb@5401b000 { + status = "disabled"; compatible = "arm,coresight-etb10", "arm,primecell"; reg = <0x5401b000 0x1000>; @@ -160,6 +162,7 @@ }; etm@54010000 { + status = "disabled"; compatible = "arm,coresight-etm3x", "arm,primecell"; reg = <0x54010000 0x1000>; @@ -205,6 +208,25 @@ >; }; + spi3_pins: pinmux_spi3_pins { + pinctrl-single,pins = < + 0x128 (PIN_INPUT | MUX_MODE1) /* sdmmc2_clk.mcspi3_clk gpio_130 */ + 0x12a (PIN_OUTPUT | MUX_MODE1) /* sdmmc2_cmd.mcspi3_simo gpio_131 */ + 0x12c (PIN_INPUT_PULLUP | MUX_MODE1) /* sdmmc2_dat0.mcspi3_somi gpio_132 */ + 0x130 (PIN_OUTPUT | MUX_MODE1) /* sdmmc2_dat2.mcspi3_cs1 gpio_134 */ + 0x132 (PIN_OUTPUT | MUX_MODE1) /* sdmmc2_dat3.mcspi3_cs0 gpio_135 */ + >; + }; + + spi4_pins: pinmux_spi4_pins { + pinctrl-single,pins = < + 0x15c (PIN_INPUT | MUX_MODE1) /* mcbsp1_clkr.mcspi4_clk gpio_156 */ + 0x160 (PIN_OUTPUT | MUX_MODE1) /* mcbsp1_dx.mcspi4_simo gpio_158 */ + 0x162 (PIN_INPUT_PULLUP | MUX_MODE1) /* mcbsp1_dr.mcspi4_somi gpio_159 */ + 0x166 (PIN_OUTPUT | MUX_MODE1) /* mcbsp1_fsx.mcspi4_cs0 gpio_161 */ + >; + }; + hsusb2_pins: pinmux_hsusb2_pins { pinctrl-single,pins = < OMAP3_CORE1_IOPAD(0x21d4, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi1_cs3.hsusb2_data2 */ @@ -279,7 +301,7 @@ }; twl_power: power { - compatible = "ti,twl4030-power-beagleboard-xm", "ti,twl4030-power-idle-osc-off"; + compatible = "ti,twl4030-power-reset"; ti,use_poweroff; }; }; @@ -310,6 +332,36 @@ status = "disabled"; }; +&mcspi3 { + pinctrl-names = "default"; + pinctrl-0 = <&spi3_pins>; + status = "okay"; + + spidev0: spi@0 { + compatible = "spidev"; + reg = <0>; + spi-max-frequency = <48000000>; + }; + + spidev1: spi@1 { + compatible = "spidev"; + reg = <1>; + spi-max-frequency = <48000000>; + }; +}; + +&mcspi4 { + pinctrl-names = "default"; + pinctrl-0 = <&spi4_pins>; + status = "okay"; + + spidev2: spi@0 { + compatible = "spidev"; + reg = <0>; + spi-max-frequency = <48000000>; + }; +}; + &twl_gpio { ti,use-leds; /* pullups: BIT(1) */ @@ -348,6 +400,21 @@ &usbhsehci { phys = <0 &hsusb2_phy>; + + #address-cells = <1>; + #size-cells = <0>; + + hub@2 { + compatible = "usb424,9514"; + reg = <2>; + #address-cells = <1>; + #size-cells = <0>; + + ethernet: usbether@1 { + compatible = "usb424,ec00"; + reg = <1>; + }; + }; }; &vaux2 { diff --git a/arch/arm/boot/dts/omap3-beagle.dts b/arch/arm/boot/dts/omap3-beagle.dts index 4be85ce59..049b5e1ca 100644 --- a/arch/arm/boot/dts/omap3-beagle.dts +++ b/arch/arm/boot/dts/omap3-beagle.dts @@ -141,6 +141,7 @@ }; etb@540000000 { + status = "disabled"; compatible = "arm,coresight-etb10", "arm,primecell"; reg = <0x5401b000 0x1000>; @@ -155,6 +156,7 @@ }; etm@54010000 { + status = "disabled"; compatible = "arm,coresight-etm3x", "arm,primecell"; reg = <0x54010000 0x1000>; @@ -271,9 +273,18 @@ codec { }; }; + + twl_power: power { + compatible = "ti,twl4030-power-reset"; + ti,use_poweroff; + }; }; }; +&i2c2 { + clock-frequency = <400000>; +}; + #include "twl4030.dtsi" #include "twl4030_omap3.dtsi" diff --git a/arch/arm/boot/dts/omap4-panda-a4.dts b/arch/arm/boot/dts/omap4-panda-a4.dts index 78d363177..67ee5b4f5 100644 --- a/arch/arm/boot/dts/omap4-panda-a4.dts +++ b/arch/arm/boot/dts/omap4-panda-a4.dts @@ -10,6 +10,18 @@ #include "omap443x.dtsi" #include "omap4-panda-common.dtsi" +&emif1 { + cs1-used; + device-handle = <&elpida_ECB240ABACN>; + status = "ok"; +}; + +&emif2 { + cs1-used; + device-handle = <&elpida_ECB240ABACN>; + status = "ok"; +}; + /* Pandaboard Rev A4+ have external pullups on SCL & SDA */ &dss_hdmi_pins { pinctrl-single,pins = < diff --git a/arch/arm/boot/dts/omap4-panda-common.dtsi b/arch/arm/boot/dts/omap4-panda-common.dtsi index 1673689e6..c6b90f022 100644 --- a/arch/arm/boot/dts/omap4-panda-common.dtsi +++ b/arch/arm/boot/dts/omap4-panda-common.dtsi @@ -463,16 +463,6 @@ }; }; -&emif1 { - cs1-used; - device-handle = <&elpida_ECB240ABACN>; -}; - -&emif2 { - cs1-used; - device-handle = <&elpida_ECB240ABACN>; -}; - &mcbsp1 { pinctrl-names = "default"; pinctrl-0 = <&mcbsp1_pins>; diff --git b/arch/arm/boot/dts/omap4-panda-es-b3.dts b/arch/arm/boot/dts/omap4-panda-es-b3.dts new file mode 100644 index 000000000..2f1dabcc6 --- /dev/null +++ b/arch/arm/boot/dts/omap4-panda-es-b3.dts @@ -0,0 +1,73 @@ +/* + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +/dts-v1/; + +#include "omap4460.dtsi" +#include "omap4-panda-common.dtsi" + +/ { + model = "TI OMAP4 PandaBoard-ES"; + compatible = "ti,omap4-panda-es", "ti,omap4-panda", "ti,omap4460", "ti,omap4430", "ti,omap4"; +}; + +/* Audio routing is differnet between PandaBoard4430 and PandaBoardES */ +&sound { + ti,model = "PandaBoardES"; + + /* Audio routing */ + ti,audio-routing = + "Headset Stereophone", "HSOL", + "Headset Stereophone", "HSOR", + "Ext Spk", "HFL", + "Ext Spk", "HFR", + "Line Out", "AUXL", + "Line Out", "AUXR", + "AFML", "Line In", + "AFMR", "Line In"; +}; + +/* PandaboardES has external pullups on SCL & SDA */ +&dss_hdmi_pins { + pinctrl-single,pins = < + 0x5a (PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_cec.hdmi_cec */ + 0x5c (PIN_INPUT | MUX_MODE0) /* hdmi_scl.hdmi_scl */ + 0x5e (PIN_INPUT | MUX_MODE0) /* hdmi_sda.hdmi_sda */ + >; +}; + +&omap4_pmx_core { + led_gpio_pins: gpio_led_pmx { + pinctrl-single,pins = < + 0xb6 (PIN_OUTPUT | MUX_MODE3) /* gpio_110 */ + >; + }; +}; + +&led_wkgpio_pins { + pinctrl-single,pins = < + 0x1c (PIN_OUTPUT | MUX_MODE3) /* gpio_wk8 */ + >; +}; + +&leds { + pinctrl-0 = < + &led_gpio_pins + &led_wkgpio_pins + >; + + heartbeat { + gpios = <&gpio4 14 GPIO_ACTIVE_HIGH>; + }; + mmc { + gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>; + }; +}; + +&gpio1 { + ti,no-reset-on-init; +}; diff --git a/arch/arm/boot/dts/omap4-panda-es.dts b/arch/arm/boot/dts/omap4-panda-es.dts index 119f8e657..5c54ccf81 100644 --- a/arch/arm/boot/dts/omap4-panda-es.dts +++ b/arch/arm/boot/dts/omap4-panda-es.dts @@ -15,6 +15,18 @@ compatible = "ti,omap4-panda-es", "ti,omap4-panda", "ti,omap4460", "ti,omap4430", "ti,omap4"; }; +&emif1 { + cs1-used; + device-handle = <&elpida_ECB240ABACN>; + status = "ok"; +}; + +&emif2 { + cs1-used; + device-handle = <&elpida_ECB240ABACN>; + status = "ok"; +}; + /* Audio routing is differnet between PandaBoard4430 and PandaBoardES */ &sound { ti,model = "PandaBoardES"; diff --git a/arch/arm/boot/dts/omap4-panda.dts b/arch/arm/boot/dts/omap4-panda.dts index a0e28b2e2..3ee41ef82 100644 --- a/arch/arm/boot/dts/omap4-panda.dts +++ b/arch/arm/boot/dts/omap4-panda.dts @@ -14,3 +14,15 @@ model = "TI OMAP4 PandaBoard"; compatible = "ti,omap4-panda", "ti,omap4430", "ti,omap4"; }; + +&emif1 { + cs1-used; + device-handle = <&elpida_ECB240ABACN>; + status = "ok"; +}; + +&emif2 { + cs1-used; + device-handle = <&elpida_ECB240ABACN>; + status = "ok"; +}; diff --git a/arch/arm/boot/dts/omap4-sdp.dts b/arch/arm/boot/dts/omap4-sdp.dts index d728ec963..fb2cda4a0 100644 --- a/arch/arm/boot/dts/omap4-sdp.dts +++ b/arch/arm/boot/dts/omap4-sdp.dts @@ -502,11 +502,13 @@ &emif1 { cs1-used; device-handle = <&elpida_ECB240ABACN>; + status = "ok"; }; &emif2 { cs1-used; device-handle = <&elpida_ECB240ABACN>; + status = "ok"; }; &keypad { diff --git a/arch/arm/boot/dts/omap4.dtsi b/arch/arm/boot/dts/omap4.dtsi index 0ced079b7..008eacbed 100644 --- a/arch/arm/boot/dts/omap4.dtsi +++ b/arch/arm/boot/dts/omap4.dtsi @@ -695,6 +695,7 @@ hw-caps-read-idle-ctrl; hw-caps-ll-interface; hw-caps-temp-alert; + status = "disabled"; }; emif2: emif@4d000000 { @@ -707,6 +708,7 @@ hw-caps-read-idle-ctrl; hw-caps-ll-interface; hw-caps-temp-alert; + status = "disabled"; }; ocp2scp@4a0ad000 { diff --git a/arch/arm/boot/dts/sun8i-h3-orangepi-one.dts b/arch/arm/boot/dts/sun8i-h3-orangepi-one.dts index 5c9b5bfa5..7c9335d48 100644 --- a/arch/arm/boot/dts/sun8i-h3-orangepi-one.dts +++ b/arch/arm/boot/dts/sun8i-h3-orangepi-one.dts @@ -94,6 +94,17 @@ status = "okay"; }; +&emac { + phy = <&phy1>; + phy-mode = "mii"; + allwinner,use-internal-phy; + allwinner,leds-active-low; + status = "okay"; + phy1: ethernet-phy@1 { + reg = <1>; + }; +}; + &mmc0 { pinctrl-names = "default"; pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>; diff --git a/arch/arm/boot/dts/sun8i-h3-orangepi-pc.dts b/arch/arm/boot/dts/sun8i-h3-orangepi-pc.dts index 3ec971285..21acd8a62 100644 --- a/arch/arm/boot/dts/sun8i-h3-orangepi-pc.dts +++ b/arch/arm/boot/dts/sun8i-h3-orangepi-pc.dts @@ -183,3 +183,14 @@ /* USB VBUS is always on */ status = "okay"; }; + +&emac { + phy = <&phy1>; + phy-mode = "mii"; + allwinner,use-internal-phy; + allwinner,leds-active-low; + status = "okay"; + phy1: ethernet-phy@1 { + reg = <1>; + }; +}; diff --git a/arch/arm/boot/dts/sun8i-h3.dtsi b/arch/arm/boot/dts/sun8i-h3.dtsi index f4ba088b2..43c4a5cf6 100644 --- a/arch/arm/boot/dts/sun8i-h3.dtsi +++ b/arch/arm/boot/dts/sun8i-h3.dtsi @@ -50,6 +50,10 @@ / { interrupt-parent = <&gic>; + aliases { + ethernet0 = &emac; + }; + cpus { #address-cells = <1>; #size-cells = <0>; @@ -530,6 +534,20 @@ #size-cells = <0>; }; + emac: ethernet@1c30000 { + compatible = "allwinner,sun8i-h3-emac"; + reg = <0x01c30000 0x104>, <0x01c00030 0x4>; + reg-names = "emac", "syscon"; + interrupts = ; + resets = <&ccu RST_BUS_EMAC>, <&ccu RST_BUS_EPHY>; + reset-names = "ahb", "ephy"; + clocks = <&ccu CLK_BUS_EMAC>, <&ccu CLK_BUS_EPHY>; + clock-names = "ahb", "ephy"; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + gic: interrupt-controller@01c81000 { compatible = "arm,cortex-a7-gic", "arm,cortex-a15-gic"; reg = <0x01c81000 0x1000>, diff --git a/arch/arm/boot/dts/tps65217.dtsi b/arch/arm/boot/dts/tps65217.dtsi index a63272422..02de56b55 100644 --- a/arch/arm/boot/dts/tps65217.dtsi +++ b/arch/arm/boot/dts/tps65217.dtsi @@ -13,6 +13,18 @@ &tps { compatible = "ti,tps65217"; + interrupt-controller; + #interrupt-cells = <1>; + + charger { + compatible = "ti,tps65217-charger"; + status = "disabled"; + }; + + pwrbutton { + compatible = "ti,tps65217-pwrbutton"; + status = "disabled"; + }; regulators { #address-cells = <1>; diff --git a/arch/arm/mach-imx/devices/Kconfig b/arch/arm/mach-imx/devices/Kconfig index 6ffe57267..bb7bd885f 100644 --- a/arch/arm/mach-imx/devices/Kconfig +++ b/arch/arm/mach-imx/devices/Kconfig @@ -68,3 +68,9 @@ config IMX_HAVE_PLATFORM_SDHCI_ESDHC_IMX config IMX_HAVE_PLATFORM_SPI_IMX bool + +config WAND_RFKILL + tristate "Wandboard RF Kill support" + depends on SOC_IMX6Q + default m + select RFKILL diff --git a/arch/arm/mach-imx/devices/Makefile b/arch/arm/mach-imx/devices/Makefile index aa6cee870..800ce9bfa 100644 --- a/arch/arm/mach-imx/devices/Makefile +++ b/arch/arm/mach-imx/devices/Makefile @@ -25,3 +25,4 @@ obj-$(CONFIG_IMX_HAVE_PLATFORM_MXC_W1) += platform-mxc_w1.o obj-$(CONFIG_IMX_HAVE_PLATFORM_SDHCI_ESDHC_IMX) += platform-sdhci-esdhc-imx.o obj-$(CONFIG_IMX_HAVE_PLATFORM_SPI_IMX) += platform-spi_imx.o obj-$(CONFIG_IMX_HAVE_PLATFORM_MX2_EMMA) += platform-mx2-emma.o +obj-$(CONFIG_WAND_RFKILL) += wand-rfkill.o diff --git b/arch/arm/mach-imx/devices/wand-rfkill.c b/arch/arm/mach-imx/devices/wand-rfkill.c new file mode 100644 index 000000000..da7ef9f42 --- /dev/null +++ b/arch/arm/mach-imx/devices/wand-rfkill.c @@ -0,0 +1,290 @@ +/* + * arch/arm/mach-imx/devices/wand-rfkill.c + * + * Copyright (C) 2013 Vladimir Ermakov + * + * based on net/rfkill/rfkill-gpio.c + * + * This software is licensed under the terms of the GNU General Public + * License version 2, as published by the Free Software Foundation, and + * may be copied, distributed, and modified under those terms. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + + +struct wand_rfkill_data { + struct rfkill *rfkill_dev; + int shutdown_gpio; + const char *shutdown_name; +}; + +static int wand_rfkill_set_block(void *data, bool blocked) +{ + struct wand_rfkill_data *rfkill = data; + + pr_debug("wandboard-rfkill: set block %d\n", blocked); + + if (blocked) { + if (gpio_is_valid(rfkill->shutdown_gpio)) + gpio_direction_output(rfkill->shutdown_gpio, 0); + } else { + if (gpio_is_valid(rfkill->shutdown_gpio)) + gpio_direction_output(rfkill->shutdown_gpio, 1); + } + + return 0; +} + +static const struct rfkill_ops wand_rfkill_ops = { + .set_block = wand_rfkill_set_block, +}; + +static int wand_rfkill_wifi_probe(struct device *dev, + struct device_node *np, + struct wand_rfkill_data *rfkill) +{ + int ret; + int wl_ref_on, wl_rst_n, wl_reg_on, wl_wake, wl_host_wake; + + wl_ref_on = of_get_named_gpio(np, "wifi-ref-on", 0); + wl_rst_n = of_get_named_gpio(np, "wifi-rst-n", 0); + wl_reg_on = of_get_named_gpio(np, "wifi-reg-on", 0); + wl_wake = of_get_named_gpio(np, "wifi-wake", 0); + wl_host_wake = of_get_named_gpio(np, "wifi-host-wake", 0); + + if (!gpio_is_valid(wl_rst_n) || !gpio_is_valid(wl_ref_on) || + !gpio_is_valid(wl_reg_on) || !gpio_is_valid(wl_wake) || + !gpio_is_valid(wl_host_wake)) { + + dev_err(dev, "incorrect wifi gpios (%d %d %d %d %d)\n", + wl_rst_n, wl_ref_on, wl_reg_on, wl_wake, wl_host_wake); + return -EINVAL; + } + + dev_info(dev, "initialize wifi chip\n"); + + gpio_request(wl_rst_n, "wl_rst_n"); + gpio_direction_output(wl_rst_n, 0); + msleep(11); + gpio_set_value(wl_rst_n, 1); + + gpio_request(wl_ref_on, "wl_ref_on"); + gpio_direction_output(wl_ref_on, 1); + + gpio_request(wl_reg_on, "wl_reg_on"); + gpio_direction_output(wl_reg_on, 1); + + gpio_request(wl_wake, "wl_wake"); + gpio_direction_output(wl_wake, 1); + + gpio_request(wl_host_wake, "wl_host_wake"); + gpio_direction_input(wl_host_wake); + + rfkill->shutdown_name = "wifi_shutdown"; + rfkill->shutdown_gpio = wl_wake; + + rfkill->rfkill_dev = rfkill_alloc("wifi-rfkill", dev, RFKILL_TYPE_WLAN, + &wand_rfkill_ops, rfkill); + if (!rfkill->rfkill_dev) { + ret = -ENOMEM; + goto wifi_fail_free_gpio; + } + + ret = rfkill_register(rfkill->rfkill_dev); + if (ret < 0) + goto wifi_fail_unregister; + + dev_info(dev, "wifi-rfkill registered.\n"); + + return 0; + +wifi_fail_unregister: + rfkill_destroy(rfkill->rfkill_dev); +wifi_fail_free_gpio: + if (gpio_is_valid(wl_rst_n)) gpio_free(wl_rst_n); + if (gpio_is_valid(wl_ref_on)) gpio_free(wl_ref_on); + if (gpio_is_valid(wl_reg_on)) gpio_free(wl_reg_on); + if (gpio_is_valid(wl_wake)) gpio_free(wl_wake); + if (gpio_is_valid(wl_host_wake)) gpio_free(wl_host_wake); + + return ret; +} + +static int wand_rfkill_bt_probe(struct device *dev, + struct device_node *np, + struct wand_rfkill_data *rfkill) +{ + int ret; + int bt_on, bt_wake, bt_host_wake; + + bt_on = of_get_named_gpio(np, "bluetooth-on", 0); + bt_wake = of_get_named_gpio(np, "bluetooth-wake", 0); + bt_host_wake = of_get_named_gpio(np, "bluetooth-host-wake", 0); + + if (!gpio_is_valid(bt_on) || !gpio_is_valid(bt_wake) || + !gpio_is_valid(bt_host_wake)) { + + dev_err(dev, "incorrect bt gpios (%d %d %d)\n", + bt_on, bt_wake, bt_host_wake); + return -EINVAL; + } + + dev_info(dev, "initialize bluetooth chip\n"); + + gpio_request(bt_on, "bt_on"); + gpio_direction_output(bt_on, 0); + msleep(11); + gpio_set_value(bt_on, 1); + + gpio_request(bt_wake, "bt_wake"); + gpio_direction_output(bt_wake, 1); + + gpio_request(bt_host_wake, "bt_host_wake"); + gpio_direction_input(bt_host_wake); + + rfkill->shutdown_name = "bluetooth_shutdown"; + rfkill->shutdown_gpio = bt_wake; + + rfkill->rfkill_dev = rfkill_alloc("bluetooth-rfkill", dev, RFKILL_TYPE_BLUETOOTH, + &wand_rfkill_ops, rfkill); + if (!rfkill->rfkill_dev) { + ret = -ENOMEM; + goto bt_fail_free_gpio; + } + + ret = rfkill_register(rfkill->rfkill_dev); + if (ret < 0) + goto bt_fail_unregister; + + dev_info(dev, "bluetooth-rfkill registered.\n"); + + return 0; + +bt_fail_unregister: + rfkill_destroy(rfkill->rfkill_dev); +bt_fail_free_gpio: + if (gpio_is_valid(bt_on)) gpio_free(bt_on); + if (gpio_is_valid(bt_wake)) gpio_free(bt_wake); + if (gpio_is_valid(bt_host_wake)) gpio_free(bt_host_wake); + + return ret; +} + +static int wand_rfkill_probe(struct platform_device *pdev) +{ + struct wand_rfkill_data *rfkill; + struct pinctrl *pinctrl; + int ret; + + dev_info(&pdev->dev, "Wandboard rfkill initialization\n"); + + if (!pdev->dev.of_node) { + dev_err(&pdev->dev, "no device tree node\n"); + return -ENODEV; + } + + rfkill = kzalloc(sizeof(*rfkill) * 2, GFP_KERNEL); + if (!rfkill) + return -ENOMEM; + + pinctrl = devm_pinctrl_get_select_default(&pdev->dev); + if (IS_ERR(pinctrl)) { + int ret = PTR_ERR(pinctrl); + dev_err(&pdev->dev, "failed to get default pinctrl: %d\n", ret); + return ret; + } + + /* setup WiFi */ + ret = wand_rfkill_wifi_probe(&pdev->dev, pdev->dev.of_node, &rfkill[0]); + if (ret < 0) + goto fail_free_rfkill; + + /* setup bluetooth */ + ret = wand_rfkill_bt_probe(&pdev->dev, pdev->dev.of_node, &rfkill[1]); + if (ret < 0) + goto fail_unregister_wifi; + + platform_set_drvdata(pdev, rfkill); + + return 0; + +fail_unregister_wifi: + if (rfkill[1].rfkill_dev) { + rfkill_unregister(rfkill[1].rfkill_dev); + rfkill_destroy(rfkill[1].rfkill_dev); + } + + /* TODO free gpio */ + +fail_free_rfkill: + kfree(rfkill); + + return ret; +} + +static int wand_rfkill_remove(struct platform_device *pdev) +{ + struct wand_rfkill_data *rfkill = platform_get_drvdata(pdev); + + dev_info(&pdev->dev, "Module unloading\n"); + + if (!rfkill) + return 0; + + /* WiFi */ + if (gpio_is_valid(rfkill[0].shutdown_gpio)) + gpio_free(rfkill[0].shutdown_gpio); + + rfkill_unregister(rfkill[0].rfkill_dev); + rfkill_destroy(rfkill[0].rfkill_dev); + + /* Bt */ + if (gpio_is_valid(rfkill[1].shutdown_gpio)) + gpio_free(rfkill[1].shutdown_gpio); + + rfkill_unregister(rfkill[1].rfkill_dev); + rfkill_destroy(rfkill[1].rfkill_dev); + + kfree(rfkill); + + return 0; +} + +static struct of_device_id wand_rfkill_match[] = { + { .compatible = "wand,imx6q-wandboard-rfkill", }, + { .compatible = "wand,imx6dl-wandboard-rfkill", }, + { .compatible = "wand,imx6qdl-wandboard-rfkill", }, + {} +}; + +static struct platform_driver wand_rfkill_driver = { + .driver = { + .name = "wandboard-rfkill", + .owner = THIS_MODULE, + .of_match_table = of_match_ptr(wand_rfkill_match), + }, + .probe = wand_rfkill_probe, + .remove = wand_rfkill_remove +}; + +module_platform_driver(wand_rfkill_driver); + +MODULE_AUTHOR("Vladimir Ermakov "); +MODULE_DESCRIPTION("Wandboard rfkill driver"); +MODULE_LICENSE("GPL v2"); diff --git a/arch/arm/mach-omap2/omap_device.c b/arch/arm/mach-omap2/omap_device.c index e920dd83e..f5eff3563 100644 --- a/arch/arm/mach-omap2/omap_device.c +++ b/arch/arm/mach-omap2/omap_device.c @@ -138,8 +138,8 @@ static int omap_device_build_from_dt(struct platform_device *pdev) struct omap_device *od; struct omap_hwmod *oh; struct device_node *node = pdev->dev.of_node; - const char *oh_name; - int oh_cnt, i, ret = 0; + const char *oh_name, *rst_name; + int oh_cnt, dstr_cnt, i, ret = 0; bool device_active = false; oh_cnt = of_property_count_strings(node, "ti,hwmods"); @@ -190,6 +190,26 @@ static int omap_device_build_from_dt(struct platform_device *pdev) omap_device_enable(pdev); pm_runtime_set_active(&pdev->dev); } + dstr_cnt = + of_property_count_strings(node, "ti,deassert-hard-reset"); + if (dstr_cnt > 0) { + for (i = 0; i < dstr_cnt; i += 2) { + of_property_read_string_index( + node, "ti,deassert-hard-reset", i, + &oh_name); + of_property_read_string_index( + node, "ti,deassert-hard-reset", i+1, + &rst_name); + oh = omap_hwmod_lookup(oh_name); + if (!oh) { + dev_warn(&pdev->dev, + "Cannot parse deassert property for '%s'\n", + oh_name); + break; + } + omap_hwmod_deassert_hardreset(oh, rst_name); + } + } odbfd_exit1: kfree(hwmods); @@ -206,12 +226,21 @@ static int _omap_device_notifier_call(struct notifier_block *nb, { struct platform_device *pdev = to_platform_device(dev); struct omap_device *od; - int err; + int i, err; switch (event) { case BUS_NOTIFY_REMOVED_DEVICE: - if (pdev->archdata.od) - omap_device_delete(pdev->archdata.od); + od = to_omap_device(pdev); + if (!od) + break; + + for (i = 0; i < od->hwmods_cnt; i++) { + /* shutdown hwmods */ + omap_hwmod_shutdown(od->hwmods[i]); + /* we don't remove clocks cause there's no API to do so */ + /* no harm done, since they will not be created next time */ + } + omap_device_delete(od); break; case BUS_NOTIFY_UNBOUND_DRIVER: od = to_omap_device(pdev); @@ -785,6 +814,8 @@ int omap_device_idle(struct platform_device *pdev) struct omap_device *od; od = to_omap_device(pdev); + if (!od) + return 0; if (od->_state != OMAP_DEVICE_STATE_ENABLED) { dev_warn(&pdev->dev, diff --git a/drivers/base/power/opp/core.c b/drivers/base/power/opp/core.c index 6441dfda4..f7a5fb4db 100644 --- a/drivers/base/power/opp/core.c +++ b/drivers/base/power/opp/core.c @@ -93,6 +93,8 @@ struct opp_table *_find_opp_table(struct device *dev) * Return: voltage in micro volt corresponding to the opp, else * return 0 * + * This is useful only for devices with single power supply. + * * Locking: This function must be called under rcu_read_lock(). opp is a rcu * protected pointer. This means that opp which could have been fetched by * opp_find_freq_{exact,ceil,floor} functions is valid as long as we are @@ -112,7 +114,7 @@ unsigned long dev_pm_opp_get_voltage(struct dev_pm_opp *opp) if (IS_ERR_OR_NULL(tmp_opp)) pr_err("%s: Invalid parameters\n", __func__); else - v = tmp_opp->u_volt; + v = tmp_opp->supplies[0].u_volt; return v; } @@ -210,6 +212,24 @@ unsigned long dev_pm_opp_get_max_clock_latency(struct device *dev) } EXPORT_SYMBOL_GPL(dev_pm_opp_get_max_clock_latency); +static int _get_regulator_count(struct device *dev) +{ + struct opp_table *opp_table; + int count; + + rcu_read_lock(); + + opp_table = _find_opp_table(dev); + if (!IS_ERR(opp_table)) + count = opp_table->regulator_count; + else + count = 0; + + rcu_read_unlock(); + + return count; +} + /** * dev_pm_opp_get_max_volt_latency() - Get max voltage latency in nanoseconds * @dev: device for which we do this operation @@ -222,34 +242,51 @@ unsigned long dev_pm_opp_get_max_volt_latency(struct device *dev) { struct opp_table *opp_table; struct dev_pm_opp *opp; - struct regulator *reg; + struct regulator *reg, **regulators; unsigned long latency_ns = 0; - unsigned long min_uV = ~0, max_uV = 0; - int ret; + int ret, i, count; + struct { + unsigned long min; + unsigned long max; + } *uV; + + count = _get_regulator_count(dev); + + /* Regulator may not be required for the device */ + if (!count) + return 0; + + regulators = kmalloc_array(count, sizeof(*regulators), GFP_KERNEL); + if (!regulators) + return 0; + + uV = kmalloc_array(count, sizeof(*uV), GFP_KERNEL); + if (!uV) + goto free_regulators; rcu_read_lock(); opp_table = _find_opp_table(dev); if (IS_ERR(opp_table)) { rcu_read_unlock(); - return 0; + goto free_uV; } - reg = opp_table->regulator; - if (IS_ERR(reg)) { - /* Regulator may not be required for device */ - rcu_read_unlock(); - return 0; - } + memcpy(regulators, opp_table->regulators, count * sizeof(*regulators)); - list_for_each_entry_rcu(opp, &opp_table->opp_list, node) { - if (!opp->available) - continue; + for (i = 0; i < count; i++) { + uV[i].min = ~0; + uV[i].max = 0; - if (opp->u_volt_min < min_uV) - min_uV = opp->u_volt_min; - if (opp->u_volt_max > max_uV) - max_uV = opp->u_volt_max; + list_for_each_entry_rcu(opp, &opp_table->opp_list, node) { + if (!opp->available) + continue; + + if (opp->supplies[i].u_volt_min < uV[i].min) + uV[i].min = opp->supplies[i].u_volt_min; + if (opp->supplies[i].u_volt_max > uV[i].max) + uV[i].max = opp->supplies[i].u_volt_max; + } } rcu_read_unlock(); @@ -258,9 +295,16 @@ unsigned long dev_pm_opp_get_max_volt_latency(struct device *dev) * The caller needs to ensure that opp_table (and hence the regulator) * isn't freed, while we are executing this routine. */ - ret = regulator_set_voltage_time(reg, min_uV, max_uV); - if (ret > 0) - latency_ns = ret * 1000; + for (i = 0; reg = regulators[i], i < count; i++) { + ret = regulator_set_voltage_time(reg, uV[i].min, uV[i].max); + if (ret > 0) + latency_ns += ret * 1000; + } + +free_uV: + kfree(uV); +free_regulators: + kfree(regulators); return latency_ns; } @@ -542,8 +586,7 @@ static struct clk *_get_opp_clk(struct device *dev) } static int _set_opp_voltage(struct device *dev, struct regulator *reg, - unsigned long u_volt, unsigned long u_volt_min, - unsigned long u_volt_max) + struct dev_pm_opp_supply *supply) { int ret; @@ -554,14 +597,78 @@ static int _set_opp_voltage(struct device *dev, struct regulator *reg, return 0; } - dev_dbg(dev, "%s: voltages (mV): %lu %lu %lu\n", __func__, u_volt_min, - u_volt, u_volt_max); + dev_dbg(dev, "%s: voltages (mV): %lu %lu %lu\n", __func__, + supply->u_volt_min, supply->u_volt, supply->u_volt_max); - ret = regulator_set_voltage_triplet(reg, u_volt_min, u_volt, - u_volt_max); + ret = regulator_set_voltage_triplet(reg, supply->u_volt_min, + supply->u_volt, supply->u_volt_max); if (ret) dev_err(dev, "%s: failed to set voltage (%lu %lu %lu mV): %d\n", - __func__, u_volt_min, u_volt, u_volt_max, ret); + __func__, supply->u_volt_min, supply->u_volt, + supply->u_volt_max, ret); + + return ret; +} + +static inline int +_generic_set_opp_clk_only(struct device *dev, struct clk *clk, + unsigned long old_freq, unsigned long freq) +{ + int ret; + + ret = clk_set_rate(clk, freq); + if (ret) { + dev_err(dev, "%s: failed to set clock rate: %d\n", __func__, + ret); + } + + return ret; +} + +static int _generic_set_opp(struct dev_pm_set_opp_data *data) +{ + struct dev_pm_opp_supply *old_supply = data->old_opp.supplies; + struct dev_pm_opp_supply *new_supply = data->new_opp.supplies; + unsigned long old_freq = data->old_opp.rate, freq = data->new_opp.rate; + struct regulator *reg = data->regulators[0]; + struct device *dev= data->dev; + int ret; + + /* This function only supports single regulator per device */ + if (WARN_ON(data->regulator_count > 1)) { + dev_err(dev, "multiple regulators are not supported\n"); + return -EINVAL; + } + + /* Scaling up? Scale voltage before frequency */ + if (freq > old_freq) { + ret = _set_opp_voltage(dev, reg, new_supply); + if (ret) + goto restore_voltage; + } + + /* Change frequency */ + ret = _generic_set_opp_clk_only(dev, data->clk, old_freq, freq); + if (ret) + goto restore_voltage; + + /* Scaling down? Scale voltage after frequency */ + if (freq < old_freq) { + ret = _set_opp_voltage(dev, reg, new_supply); + if (ret) + goto restore_freq; + } + + return 0; + +restore_freq: + if (_generic_set_opp_clk_only(dev, data->clk, freq, old_freq)) + dev_err(dev, "%s: failed to restore old-freq (%lu Hz)\n", + __func__, old_freq); +restore_voltage: + /* This shouldn't harm even if the voltages weren't updated earlier */ + if (old_supply->u_volt) + _set_opp_voltage(dev, reg, old_supply); return ret; } @@ -579,13 +686,13 @@ static int _set_opp_voltage(struct device *dev, struct regulator *reg, int dev_pm_opp_set_rate(struct device *dev, unsigned long target_freq) { struct opp_table *opp_table; + unsigned long freq, old_freq; + int (*set_opp)(struct dev_pm_set_opp_data *data); struct dev_pm_opp *old_opp, *opp; - struct regulator *reg; + struct regulator **regulators; + struct dev_pm_set_opp_data *data; struct clk *clk; - unsigned long freq, old_freq; - unsigned long u_volt, u_volt_min, u_volt_max; - unsigned long old_u_volt, old_u_volt_min, old_u_volt_max; - int ret; + int ret, size; if (unlikely(!target_freq)) { dev_err(dev, "%s: Invalid target frequency %lu\n", __func__, @@ -634,64 +741,54 @@ int dev_pm_opp_set_rate(struct device *dev, unsigned long target_freq) return ret; } - if (IS_ERR(old_opp)) { - old_u_volt = 0; - } else { - old_u_volt = old_opp->u_volt; - old_u_volt_min = old_opp->u_volt_min; - old_u_volt_max = old_opp->u_volt_max; - } - - u_volt = opp->u_volt; - u_volt_min = opp->u_volt_min; - u_volt_max = opp->u_volt_max; - - reg = opp_table->regulator; + dev_dbg(dev, "%s: switching OPP: %lu Hz --> %lu Hz\n", __func__, + old_freq, freq); - rcu_read_unlock(); + regulators = opp_table->regulators; - /* Scaling up? Scale voltage before frequency */ - if (freq > old_freq) { - ret = _set_opp_voltage(dev, reg, u_volt, u_volt_min, - u_volt_max); - if (ret) - goto restore_voltage; - } + /* Only frequency scaling */ + if (!regulators) { + unsigned long u_volt = opp->supplies[0].u_volt; - /* Change frequency */ + rcu_read_unlock(); - dev_dbg(dev, "%s: switching OPP: %lu Hz --> %lu Hz\n", - __func__, old_freq, freq); + /* + * DT contained supply ratings? Consider platform failed to set + * regulators. + */ + if (unlikely(u_volt)) { + dev_err(dev, "%s: Regulator not registered with OPP core\n", + __func__); + return -EINVAL; + } - ret = clk_set_rate(clk, freq); - if (ret) { - dev_err(dev, "%s: failed to set clock rate: %d\n", __func__, - ret); - goto restore_voltage; + return _generic_set_opp_clk_only(dev, clk, old_freq, freq); } - /* Scaling down? Scale voltage after frequency */ - if (freq < old_freq) { - ret = _set_opp_voltage(dev, reg, u_volt, u_volt_min, - u_volt_max); - if (ret) - goto restore_freq; - } + if (opp_table->set_opp) + set_opp = opp_table->set_opp; + else + set_opp = _generic_set_opp; + + data = opp_table->set_opp_data; + data->regulators = regulators; + data->regulator_count = opp_table->regulator_count; + data->clk = clk; + data->dev = dev; + + data->old_opp.rate = old_freq; + size = sizeof(*opp->supplies) * opp_table->regulator_count; + if (IS_ERR(old_opp)) + memset(data->old_opp.supplies, 0, size); + else + memcpy(data->old_opp.supplies, old_opp->supplies, size); - return 0; + data->new_opp.rate = freq; + memcpy(data->new_opp.supplies, opp->supplies, size); -restore_freq: - if (clk_set_rate(clk, old_freq)) - dev_err(dev, "%s: failed to restore old-freq (%lu Hz)\n", - __func__, old_freq); -restore_voltage: - /* This shouldn't harm even if the voltages weren't updated earlier */ - if (old_u_volt) { - _set_opp_voltage(dev, reg, old_u_volt, old_u_volt_min, - old_u_volt_max); - } + rcu_read_unlock(); - return ret; + return set_opp(data); } EXPORT_SYMBOL_GPL(dev_pm_opp_set_rate); @@ -774,9 +871,6 @@ static struct opp_table *_add_opp_table(struct device *dev) _of_init_opp_table(opp_table, dev); - /* Set regulator to a non-NULL error value */ - opp_table->regulator = ERR_PTR(-ENXIO); - /* Find clk for the device */ opp_table->clk = clk_get(dev, NULL); if (IS_ERR(opp_table->clk)) { @@ -825,7 +919,10 @@ static void _remove_opp_table(struct opp_table *opp_table) if (opp_table->prop_name) return; - if (!IS_ERR(opp_table->regulator)) + if (opp_table->regulators) + return; + + if (opp_table->set_opp) return; /* Release clk */ @@ -934,34 +1031,50 @@ struct dev_pm_opp *_allocate_opp(struct device *dev, struct opp_table **opp_table) { struct dev_pm_opp *opp; + int count, supply_size; + struct opp_table *table; - /* allocate new OPP node */ - opp = kzalloc(sizeof(*opp), GFP_KERNEL); - if (!opp) + table = _add_opp_table(dev); + if (!table) return NULL; - INIT_LIST_HEAD(&opp->node); + /* Allocate space for at least one supply */ + count = table->regulator_count ? table->regulator_count : 1; + supply_size = sizeof(*opp->supplies) * count; - *opp_table = _add_opp_table(dev); - if (!*opp_table) { - kfree(opp); + /* allocate new OPP node and supplies structures */ + opp = kzalloc(sizeof(*opp) + supply_size, GFP_KERNEL); + if (!opp) { + kfree(table); return NULL; } + /* Put the supplies at the end of the OPP structure as an empty array */ + opp->supplies = (struct dev_pm_opp_supply *)(opp + 1); + INIT_LIST_HEAD(&opp->node); + + *opp_table = table; + return opp; } static bool _opp_supported_by_regulators(struct dev_pm_opp *opp, struct opp_table *opp_table) { - struct regulator *reg = opp_table->regulator; - - if (!IS_ERR(reg) && - !regulator_is_supported_voltage(reg, opp->u_volt_min, - opp->u_volt_max)) { - pr_warn("%s: OPP minuV: %lu maxuV: %lu, not supported by regulator\n", - __func__, opp->u_volt_min, opp->u_volt_max); - return false; + struct regulator *reg; + int i; + + for (i = 0; i < opp_table->regulator_count; i++) { + reg = opp_table->regulators[i]; + + if (!regulator_is_supported_voltage(reg, + opp->supplies[i].u_volt_min, + opp->supplies[i].u_volt_max)) { + pr_warn("%s: OPP minuV: %lu maxuV: %lu, not supported by regulator\n", + __func__, opp->supplies[i].u_volt_min, + opp->supplies[i].u_volt_max); + return false; + } } return true; @@ -993,11 +1106,13 @@ int _opp_add(struct device *dev, struct dev_pm_opp *new_opp, /* Duplicate OPPs */ dev_warn(dev, "%s: duplicate OPPs detected. Existing: freq: %lu, volt: %lu, enabled: %d. New: freq: %lu, volt: %lu, enabled: %d\n", - __func__, opp->rate, opp->u_volt, opp->available, - new_opp->rate, new_opp->u_volt, new_opp->available); + __func__, opp->rate, opp->supplies[0].u_volt, + opp->available, new_opp->rate, + new_opp->supplies[0].u_volt, new_opp->available); - return opp->available && new_opp->u_volt == opp->u_volt ? - 0 : -EEXIST; + /* Should we compare voltages for all regulators here ? */ + return opp->available && + new_opp->supplies[0].u_volt == opp->supplies[0].u_volt ? 0 : -EEXIST; } new_opp->opp_table = opp_table; @@ -1064,9 +1179,9 @@ int _opp_add_v1(struct device *dev, unsigned long freq, long u_volt, /* populate the opp table */ new_opp->rate = freq; tol = u_volt * opp_table->voltage_tolerance_v1 / 100; - new_opp->u_volt = u_volt; - new_opp->u_volt_min = u_volt - tol; - new_opp->u_volt_max = u_volt + tol; + new_opp->supplies[0].u_volt = u_volt; + new_opp->supplies[0].u_volt_min = u_volt - tol; + new_opp->supplies[0].u_volt_max = u_volt + tol; new_opp->available = true; new_opp->dynamic = dynamic; @@ -1310,13 +1425,47 @@ void dev_pm_opp_put_prop_name(struct device *dev) } EXPORT_SYMBOL_GPL(dev_pm_opp_put_prop_name); +static int _allocate_set_opp_data(struct opp_table *opp_table) +{ + struct dev_pm_set_opp_data *data; + int len, count = opp_table->regulator_count; + + if (WARN_ON(!count)) + return -EINVAL; + + /* space for set_opp_data */ + len = sizeof(*data); + + /* space for old_opp.supplies and new_opp.supplies */ + len += 2 * sizeof(struct dev_pm_opp_supply) * count; + + data = kzalloc(len, GFP_KERNEL); + if (!data) + return -ENOMEM; + + data->old_opp.supplies = (void *)(data + 1); + data->new_opp.supplies = data->old_opp.supplies + count; + + opp_table->set_opp_data = data; + + return 0; +} + +static void _free_set_opp_data(struct opp_table *opp_table) +{ + kfree(opp_table->set_opp_data); + opp_table->set_opp_data = NULL; +} + /** - * dev_pm_opp_set_regulator() - Set regulator name for the device + * dev_pm_opp_set_regulators() - Set regulator names for the device * @dev: Device for which regulator name is being set. - * @name: Name of the regulator. + * @names: Array of pointers to the names of the regulator. + * @count: Number of regulators. * * In order to support OPP switching, OPP layer needs to know the name of the - * device's regulator, as the core would be required to switch voltages as well. + * device's regulators, as the core would be required to switch voltages as + * well. * * This must be called before any OPPs are initialized for the device. * @@ -1326,11 +1475,12 @@ EXPORT_SYMBOL_GPL(dev_pm_opp_put_prop_name); * that this function is *NOT* called under RCU protection or in contexts where * mutex cannot be locked. */ -struct opp_table *dev_pm_opp_set_regulator(struct device *dev, const char *name) +int dev_pm_opp_set_regulators(struct device *dev, const char * const names[], + unsigned int count) { struct opp_table *opp_table; struct regulator *reg; - int ret; + int ret, i; mutex_lock(&opp_table_lock); @@ -1346,38 +1496,62 @@ struct opp_table *dev_pm_opp_set_regulator(struct device *dev, const char *name) goto err; } - /* Already have a regulator set */ - if (WARN_ON(!IS_ERR(opp_table->regulator))) { + /* Already have regulators set */ + if (opp_table->regulators) { ret = -EBUSY; goto err; } - /* Allocate the regulator */ - reg = regulator_get_optional(dev, name); - if (IS_ERR(reg)) { - ret = PTR_ERR(reg); - if (ret != -EPROBE_DEFER) - dev_err(dev, "%s: no regulator (%s) found: %d\n", - __func__, name, ret); + + opp_table->regulators = kmalloc_array(count, + sizeof(*opp_table->regulators), + GFP_KERNEL); + if (!opp_table->regulators) { + ret = -ENOMEM; goto err; } - opp_table->regulator = reg; + for (i = 0; i < count; i++) { + reg = regulator_get_optional(dev, names[i]); + if (IS_ERR(reg)) { + ret = PTR_ERR(reg); + if (ret != -EPROBE_DEFER) + dev_err(dev, "%s: regulator (%s) not found: %d\n", + __func__, names[i], ret); + goto free_regulators; + } + + opp_table->regulators[i] = reg; + } + + opp_table->regulator_count = count; + + /* Allocate block only once to pass to set_opp() routines */ + ret = _allocate_set_opp_data(opp_table); + if (ret) + goto free_regulators; mutex_unlock(&opp_table_lock); - return opp_table; + return 0; +free_regulators: + while (i != 0) + regulator_put(opp_table->regulators[--i]); + + kfree(opp_table->regulators); + opp_table->regulators = NULL; + opp_table->regulator_count = 0; err: _remove_opp_table(opp_table); unlock: mutex_unlock(&opp_table_lock); - return ERR_PTR(ret); + return ret; } -EXPORT_SYMBOL_GPL(dev_pm_opp_set_regulator); +EXPORT_SYMBOL_GPL(dev_pm_opp_set_regulators); /** - * dev_pm_opp_put_regulator() - Releases resources blocked for regulator - * @opp_table: OPP table returned from dev_pm_opp_set_regulator(). + * dev_pm_opp_put_regulators() - Releases resources blocked for regulators + * @dev: Device for which regulators were set. * * Locking: The internal opp_table and opp structures are RCU protected. * Hence this function internally uses RCU updater strategy with mutex locks @@ -1385,20 +1559,140 @@ EXPORT_SYMBOL_GPL(dev_pm_opp_set_regulator); * that this function is *NOT* called under RCU protection or in contexts where * mutex cannot be locked. */ -void dev_pm_opp_put_regulator(struct opp_table *opp_table) +void dev_pm_opp_put_regulators(struct device *dev) { + struct opp_table *opp_table; + int i; + mutex_lock(&opp_table_lock); - if (IS_ERR(opp_table->regulator)) { - pr_err("%s: Doesn't have regulator set\n", __func__); + /* Check for existing table for 'dev' first */ + opp_table = _find_opp_table(dev); + if (IS_ERR(opp_table)) { + dev_err(dev, "Failed to find opp_table: %ld\n", + PTR_ERR(opp_table)); + goto unlock; + } + + if (!opp_table->regulators) { + dev_err(dev, "%s: Doesn't have regulators set\n", __func__); + goto unlock; + } + + /* Make sure there are no concurrent readers while updating opp_table */ + WARN_ON(!list_empty(&opp_table->opp_list)); + + for (i = opp_table->regulator_count - 1; i >= 0; i--) + regulator_put(opp_table->regulators[i]); + + _free_set_opp_data(opp_table); + + kfree(opp_table->regulators); + opp_table->regulators = NULL; + opp_table->regulator_count = 0; + + /* Try freeing opp_table if this was the last blocking resource */ + _remove_opp_table(opp_table); + +unlock: + mutex_unlock(&opp_table_lock); +} +EXPORT_SYMBOL_GPL(dev_pm_opp_put_regulators); + +/** + * dev_pm_opp_register_set_opp_helper() - Register custom set OPP helper + * @dev: Device for which the helper is getting registered. + * @set_opp: Custom set OPP helper. + * + * This is useful to support complex platforms (like platforms with multiple + * regulators per device), instead of the generic OPP set rate helper. + * + * This must be called before any OPPs are initialized for the device. + * + * Locking: The internal opp_table and opp structures are RCU protected. + * Hence this function internally uses RCU updater strategy with mutex locks + * to keep the integrity of the internal data structures. Callers should ensure + * that this function is *NOT* called under RCU protection or in contexts where + * mutex cannot be locked. + */ +int dev_pm_opp_register_set_opp_helper(struct device *dev, + int (*set_opp)(struct dev_pm_set_opp_data *data)) +{ + struct opp_table *opp_table; + int ret; + + if (!set_opp) + return -EINVAL; + + mutex_lock(&opp_table_lock); + + opp_table = _add_opp_table(dev); + if (!opp_table) { + ret = -ENOMEM; + goto unlock; + } + + /* This should be called before OPPs are initialized */ + if (WARN_ON(!list_empty(&opp_table->opp_list))) { + ret = -EBUSY; + goto err; + } + + /* Already have custom set_opp helper */ + if (WARN_ON(opp_table->set_opp)) { + ret = -EBUSY; + goto err; + } + + opp_table->set_opp = set_opp; + + mutex_unlock(&opp_table_lock); + return 0; + +err: + _remove_opp_table(opp_table); +unlock: + mutex_unlock(&opp_table_lock); + + return ret; +} +EXPORT_SYMBOL_GPL(dev_pm_opp_register_set_opp_helper); + +/** + * dev_pm_opp_register_put_opp_helper() - Releases resources blocked for + * set_opp helper + * @dev: Device for which custom set_opp helper has to be cleared. + * + * Locking: The internal opp_table and opp structures are RCU protected. + * Hence this function internally uses RCU updater strategy with mutex locks + * to keep the integrity of the internal data structures. Callers should ensure + * that this function is *NOT* called under RCU protection or in contexts where + * mutex cannot be locked. + */ +void dev_pm_opp_register_put_opp_helper(struct device *dev) +{ + struct opp_table *opp_table; + + mutex_lock(&opp_table_lock); + + /* Check for existing table for 'dev' first */ + opp_table = _find_opp_table(dev); + if (IS_ERR(opp_table)) { + dev_err(dev, "Failed to find opp_table: %ld\n", + PTR_ERR(opp_table)); + goto unlock; + } + + if (!opp_table->set_opp) { + dev_err(dev, "%s: Doesn't have custom set_opp helper set\n", + __func__); goto unlock; } /* Make sure there are no concurrent readers while updating opp_table */ WARN_ON(!list_empty(&opp_table->opp_list)); - regulator_put(opp_table->regulator); - opp_table->regulator = ERR_PTR(-ENXIO); + opp_table->set_opp = NULL; /* Try freeing opp_table if this was the last blocking resource */ _remove_opp_table(opp_table); @@ -1406,7 +1700,7 @@ void dev_pm_opp_put_regulator(struct opp_table *opp_table) unlock: mutex_unlock(&opp_table_lock); } -EXPORT_SYMBOL_GPL(dev_pm_opp_put_regulator); +EXPORT_SYMBOL_GPL(dev_pm_opp_register_put_opp_helper); /** * dev_pm_opp_add() - Add an OPP table from a table definitions diff --git a/drivers/base/power/opp/debugfs.c b/drivers/base/power/opp/debugfs.c index ef1ae6b52..95f433db4 100644 --- a/drivers/base/power/opp/debugfs.c +++ b/drivers/base/power/opp/debugfs.c @@ -15,6 +15,7 @@ #include #include #include +#include #include "opp.h" @@ -34,6 +35,46 @@ void opp_debug_remove_one(struct dev_pm_opp *opp) debugfs_remove_recursive(opp->dentry); } +static bool opp_debug_create_supplies(struct dev_pm_opp *opp, + struct opp_table *opp_table, + struct dentry *pdentry) +{ + struct dentry *d; + int i = 0; + char *name; + + /* Always create at least supply-0 directory */ + do { + name = kasprintf(GFP_KERNEL, "supply-%d", i); + + /* Create per-opp directory */ + d = debugfs_create_dir(name, pdentry); + + kfree(name); + + if (!d) + return false; + + if (!debugfs_create_ulong("u_volt_target", S_IRUGO, d, + &opp->supplies[i].u_volt)) + return false; + + if (!debugfs_create_ulong("u_volt_min", S_IRUGO, d, + &opp->supplies[i].u_volt_min)) + return false; + + if (!debugfs_create_ulong("u_volt_max", S_IRUGO, d, + &opp->supplies[i].u_volt_max)) + return false; + + if (!debugfs_create_ulong("u_amp", S_IRUGO, d, + &opp->supplies[i].u_amp)) + return false; + } while (++i < opp_table->regulator_count); + + return true; +} + int opp_debug_create_one(struct dev_pm_opp *opp, struct opp_table *opp_table) { struct dentry *pdentry = opp_table->dentry; @@ -63,16 +104,7 @@ int opp_debug_create_one(struct dev_pm_opp *opp, struct opp_table *opp_table) if (!debugfs_create_ulong("rate_hz", S_IRUGO, d, &opp->rate)) return -ENOMEM; - if (!debugfs_create_ulong("u_volt_target", S_IRUGO, d, &opp->u_volt)) - return -ENOMEM; - - if (!debugfs_create_ulong("u_volt_min", S_IRUGO, d, &opp->u_volt_min)) - return -ENOMEM; - - if (!debugfs_create_ulong("u_volt_max", S_IRUGO, d, &opp->u_volt_max)) - return -ENOMEM; - - if (!debugfs_create_ulong("u_amp", S_IRUGO, d, &opp->u_amp)) + if (!opp_debug_create_supplies(opp, opp_table, d)) return -ENOMEM; if (!debugfs_create_ulong("clock_latency_ns", S_IRUGO, d, diff --git a/drivers/base/power/opp/of.c b/drivers/base/power/opp/of.c index 5552211e6..8c869aaba 100644 --- a/drivers/base/power/opp/of.c +++ b/drivers/base/power/opp/of.c @@ -17,6 +17,7 @@ #include #include #include +#include #include #include "opp.h" @@ -101,16 +102,16 @@ static bool _opp_is_supported(struct device *dev, struct opp_table *opp_table, return true; } -/* TODO: Support multiple regulators */ static int opp_parse_supplies(struct dev_pm_opp *opp, struct device *dev, struct opp_table *opp_table) { - u32 microvolt[3] = {0}; - u32 val; - int count, ret; + u32 *microvolt, *microamp = NULL; + int supplies, vcount, icount, ret, i, j; struct property *prop = NULL; char name[NAME_MAX]; + supplies = opp_table->regulator_count ? opp_table->regulator_count : 1; + /* Search for "opp-microvolt-" */ if (opp_table->prop_name) { snprintf(name, sizeof(name), "opp-microvolt-%s", @@ -128,34 +129,29 @@ static int opp_parse_supplies(struct dev_pm_opp *opp, struct device *dev, return 0; } - count = of_property_count_u32_elems(opp->np, name); - if (count < 0) { + vcount = of_property_count_u32_elems(opp->np, name); + if (vcount < 0) { dev_err(dev, "%s: Invalid %s property (%d)\n", - __func__, name, count); - return count; + __func__, name, vcount); + return vcount; } - /* There can be one or three elements here */ - if (count != 1 && count != 3) { - dev_err(dev, "%s: Invalid number of elements in %s property (%d)\n", - __func__, name, count); + /* There can be one or three elements per supply */ + if (vcount != supplies && vcount != supplies * 3) { + dev_err(dev, "%s: Invalid number of elements in %s property (%d) with supplies (%d)\n", + __func__, name, vcount, supplies); return -EINVAL; } - ret = of_property_read_u32_array(opp->np, name, microvolt, count); + microvolt = kmalloc_array(vcount, sizeof(*microvolt), GFP_KERNEL); + if (!microvolt) + return -ENOMEM; + + ret = of_property_read_u32_array(opp->np, name, microvolt, vcount); if (ret) { dev_err(dev, "%s: error parsing %s: %d\n", __func__, name, ret); - return -EINVAL; - } - - opp->u_volt = microvolt[0]; - - if (count == 1) { - opp->u_volt_min = opp->u_volt; - opp->u_volt_max = opp->u_volt; - } else { - opp->u_volt_min = microvolt[1]; - opp->u_volt_max = microvolt[2]; + ret = -EINVAL; + goto free_microvolt; } /* Search for "opp-microamp-" */ @@ -172,10 +168,59 @@ static int opp_parse_supplies(struct dev_pm_opp *opp, struct device *dev, prop = of_find_property(opp->np, name, NULL); } - if (prop && !of_property_read_u32(opp->np, name, &val)) - opp->u_amp = val; + if (prop) { + icount = of_property_count_u32_elems(opp->np, name); + if (icount < 0) { + dev_err(dev, "%s: Invalid %s property (%d)\n", __func__, + name, icount); + ret = icount; + goto free_microvolt; + } - return 0; + if (icount != supplies) { + dev_err(dev, "%s: Invalid number of elements in %s property (%d) with supplies (%d)\n", + __func__, name, icount, supplies); + ret = -EINVAL; + goto free_microvolt; + } + + microamp = kmalloc_array(icount, sizeof(*microamp), GFP_KERNEL); + if (!microamp) { + ret = -EINVAL; + goto free_microvolt; + } + + ret = of_property_read_u32_array(opp->np, name, microamp, + icount); + if (ret) { + dev_err(dev, "%s: error parsing %s: %d\n", __func__, + name, ret); + ret = -EINVAL; + goto free_microamp; + } + } + + for (i = 0, j = 0; i < supplies; i++) { + opp->supplies[i].u_volt = microvolt[j++]; + + if (vcount == supplies) { + opp->supplies[i].u_volt_min = opp->supplies[i].u_volt; + opp->supplies[i].u_volt_max = opp->supplies[i].u_volt; + } else { + opp->supplies[i].u_volt_min = microvolt[j++]; + opp->supplies[i].u_volt_max = microvolt[j++]; + } + + if (microamp) + opp->supplies[i].u_amp = microamp[i]; + } + +free_microamp: + kfree(microamp); +free_microvolt: + kfree(microvolt); + + return ret; } /** @@ -198,7 +243,7 @@ void dev_pm_opp_of_remove_table(struct device *dev) EXPORT_SYMBOL_GPL(dev_pm_opp_of_remove_table); /* Returns opp descriptor node for a device, caller must do of_node_put() */ -struct device_node *_of_get_opp_desc_node(struct device *dev) +struct device_node *dev_pm_opp_of_get_opp_desc_node(struct device *dev) { /* * TODO: Support for multiple OPP tables. @@ -209,6 +254,7 @@ struct device_node *_of_get_opp_desc_node(struct device *dev) return of_parse_phandle(dev->of_node, "operating-points-v2", 0); } +EXPORT_SYMBOL_GPL(dev_pm_opp_of_get_opp_desc_node); /** * _opp_add_static_v2() - Allocate static OPPs (As per 'v2' DT bindings) @@ -303,9 +349,9 @@ static int _opp_add_static_v2(struct device *dev, struct device_node *np) mutex_unlock(&opp_table_lock); pr_debug("%s: turbo:%d rate:%lu uv:%lu uvmin:%lu uvmax:%lu latency:%lu\n", - __func__, new_opp->turbo, new_opp->rate, new_opp->u_volt, - new_opp->u_volt_min, new_opp->u_volt_max, - new_opp->clock_latency_ns); + __func__, new_opp->turbo, new_opp->rate, + new_opp->supplies[0].u_volt, new_opp->supplies[0].u_volt_min, + new_opp->supplies[0].u_volt_max, new_opp->clock_latency_ns); /* * Notify the changes in the availability of the operable @@ -450,7 +496,7 @@ int dev_pm_opp_of_add_table(struct device *dev) * OPPs have two version of bindings now. The older one is deprecated, * try for the new binding first. */ - opp_np = _of_get_opp_desc_node(dev); + opp_np = dev_pm_opp_of_get_opp_desc_node(dev); if (!opp_np) { /* * Try old-deprecated bindings for backward compatibility with @@ -560,7 +606,7 @@ int dev_pm_opp_of_get_sharing_cpus(struct device *cpu_dev, int cpu, ret = 0; /* Get OPP descriptor node */ - np = _of_get_opp_desc_node(cpu_dev); + np = dev_pm_opp_of_get_opp_desc_node(cpu_dev); if (!np) { dev_dbg(cpu_dev, "%s: Couldn't find cpu_dev node.\n", __func__); return -ENOENT; @@ -585,7 +631,7 @@ int dev_pm_opp_of_get_sharing_cpus(struct device *cpu_dev, } /* Get OPP descriptor node */ - tmp_np = _of_get_opp_desc_node(tcpu_dev); + tmp_np = dev_pm_opp_of_get_opp_desc_node(tcpu_dev); if (!tmp_np) { dev_err(tcpu_dev, "%s: Couldn't find tcpu_dev node.\n", __func__); diff --git a/drivers/base/power/opp/opp.h b/drivers/base/power/opp/opp.h index fabd5ca1a..af9f2b849 100644 --- a/drivers/base/power/opp/opp.h +++ b/drivers/base/power/opp/opp.h @@ -61,10 +61,7 @@ extern struct list_head opp_tables; * @turbo: true if turbo (boost) OPP * @suspend: true if suspend OPP * @rate: Frequency in hertz - * @u_volt: Target voltage in microvolts corresponding to this OPP - * @u_volt_min: Minimum voltage in microvolts corresponding to this OPP - * @u_volt_max: Maximum voltage in microvolts corresponding to this OPP - * @u_amp: Maximum current drawn by the device in microamperes + * @supplies: Power supplies voltage/current values * @clock_latency_ns: Latency (in nanoseconds) of switching to this OPP's * frequency from any other OPP's frequency. * @opp_table: points back to the opp_table struct this opp belongs to @@ -83,10 +80,8 @@ struct dev_pm_opp { bool suspend; unsigned long rate; - unsigned long u_volt; - unsigned long u_volt_min; - unsigned long u_volt_max; - unsigned long u_amp; + struct dev_pm_opp_supply *supplies; + unsigned long clock_latency_ns; struct opp_table *opp_table; @@ -144,7 +139,10 @@ enum opp_table_access { * @supported_hw_count: Number of elements in supported_hw array. * @prop_name: A name to postfix to many DT properties, while parsing them. * @clk: Device's clock handle - * @regulator: Supply regulator + * @regulators: Supply regulators + * @regulator_count: Number of power supply regulators + * @set_opp: Platform specific set_opp callback + * @set_opp_data: Data to be passed to set_opp callback * @dentry: debugfs dentry pointer of the real device directory (not links). * @dentry_name: Name of the real dentry. * @@ -179,7 +177,11 @@ struct opp_table { unsigned int supported_hw_count; const char *prop_name; struct clk *clk; - struct regulator *regulator; + struct regulator **regulators; + unsigned int regulator_count; + + int (*set_opp)(struct dev_pm_set_opp_data *data); + struct dev_pm_set_opp_data *set_opp_data; #ifdef CONFIG_DEBUG_FS struct dentry *dentry; @@ -190,7 +192,6 @@ struct opp_table { /* Routines internal to opp core */ struct opp_table *_find_opp_table(struct device *dev); struct opp_device *_add_opp_dev(const struct device *dev, struct opp_table *opp_table); -struct device_node *_of_get_opp_desc_node(struct device *dev); void _dev_pm_opp_remove_table(struct device *dev, bool remove_all); struct dev_pm_opp *_allocate_opp(struct device *dev, struct opp_table **opp_table); int _opp_add(struct device *dev, struct dev_pm_opp *new_opp, struct opp_table *opp_table); diff --git a/drivers/bus/Kconfig b/drivers/bus/Kconfig index 787510571..bbd5afd07 100644 --- a/drivers/bus/Kconfig +++ b/drivers/bus/Kconfig @@ -120,7 +120,6 @@ config QCOM_EBI2 config SIMPLE_PM_BUS bool "Simple Power-Managed Bus Driver" depends on OF && PM - depends on ARCH_RENESAS || COMPILE_TEST help Driver for transparent busses that don't need a real driver, but where the bus controller is part of a PM domain, or under the control diff --git a/drivers/cpufreq/Kconfig.arm b/drivers/cpufreq/Kconfig.arm index d89b8afe2..665f11dbd 100644 --- a/drivers/cpufreq/Kconfig.arm +++ b/drivers/cpufreq/Kconfig.arm @@ -234,6 +234,17 @@ config ARM_TEGRA124_CPUFREQ help This adds the CPUFreq driver support for Tegra124 SOCs. +config ARM_TI_CPUFREQ + bool "Texas Instruments CPUFreq support" + depends on ARCH_OMAP2PLUS + help + This driver enables valid OPPs on the running platform based on + values contained within the SoC in use. Enable this in order to + use the cpufreq-dt driver on all Texas Instruments platforms that + provide dt based operating-points-v2 tables with opp-supported-hw + data provided. Required for cpufreq support on AM335x, AM437x, + DRA7x, and AM57x platforms. + config ARM_PXA2xx_CPUFREQ tristate "Intel PXA2xx CPUfreq driver" depends on PXA27x || PXA25x diff --git a/drivers/cpufreq/Makefile b/drivers/cpufreq/Makefile index 0a9b6a093..5b1b6ec0a 100644 --- a/drivers/cpufreq/Makefile +++ b/drivers/cpufreq/Makefile @@ -77,6 +77,7 @@ obj-$(CONFIG_ARM_SPEAR_CPUFREQ) += spear-cpufreq.o obj-$(CONFIG_ARM_STI_CPUFREQ) += sti-cpufreq.o obj-$(CONFIG_ARM_TEGRA20_CPUFREQ) += tegra20-cpufreq.o obj-$(CONFIG_ARM_TEGRA124_CPUFREQ) += tegra124-cpufreq.o +obj-$(CONFIG_ARM_TI_CPUFREQ) += ti-cpufreq.o obj-$(CONFIG_ARM_VEXPRESS_SPC_CPUFREQ) += vexpress-spc-cpufreq.o obj-$(CONFIG_ACPI_CPPC_CPUFREQ) += cppc_cpufreq.o obj-$(CONFIG_MACH_MVEBU_V7) += mvebu-cpufreq.o diff --git a/drivers/cpufreq/cpufreq-dt-platdev.c b/drivers/cpufreq/cpufreq-dt-platdev.c index 712676264..d2637e1a5 100644 --- a/drivers/cpufreq/cpufreq-dt-platdev.c +++ b/drivers/cpufreq/cpufreq-dt-platdev.c @@ -72,8 +72,6 @@ static const struct of_device_id machines[] __initconst = { { .compatible = "sigma,tango4" }, - { .compatible = "ti,am33xx", }, - { .compatible = "ti,dra7", }, { .compatible = "ti,omap2", }, { .compatible = "ti,omap3", }, { .compatible = "ti,omap4", }, diff --git a/drivers/cpufreq/cpufreq-dt.c b/drivers/cpufreq/cpufreq-dt.c index 4d3ec92cb..15cb26118 100644 --- a/drivers/cpufreq/cpufreq-dt.c +++ b/drivers/cpufreq/cpufreq-dt.c @@ -28,7 +28,6 @@ #include "cpufreq-dt.h" struct private_data { - struct opp_table *opp_table; struct device *cpu_dev; struct thermal_cooling_device *cdev; const char *reg_name; @@ -144,7 +143,6 @@ static int resources_available(void) static int cpufreq_init(struct cpufreq_policy *policy) { struct cpufreq_frequency_table *freq_table; - struct opp_table *opp_table = NULL; struct private_data *priv; struct device *cpu_dev; struct clk *cpu_clk; @@ -188,9 +186,11 @@ static int cpufreq_init(struct cpufreq_policy *policy) */ name = find_supply_name(cpu_dev); if (name) { - opp_table = dev_pm_opp_set_regulator(cpu_dev, name); - if (IS_ERR(opp_table)) { - ret = PTR_ERR(opp_table); + const char *names[] = {name}; + + ret = dev_pm_opp_set_regulators(cpu_dev, names, + ARRAY_SIZE(names)); + if (ret) { dev_err(cpu_dev, "Failed to set regulator for cpu%d: %d\n", policy->cpu, ret); goto out_put_clk; @@ -240,7 +240,6 @@ static int cpufreq_init(struct cpufreq_policy *policy) } priv->reg_name = name; - priv->opp_table = opp_table; ret = dev_pm_opp_init_cpufreq_table(cpu_dev, &freq_table); if (ret) { @@ -289,7 +288,7 @@ static int cpufreq_init(struct cpufreq_policy *policy) out_free_opp: dev_pm_opp_of_cpumask_remove_table(policy->cpus); if (name) - dev_pm_opp_put_regulator(opp_table); + dev_pm_opp_put_regulators(cpu_dev); out_put_clk: clk_put(cpu_clk); @@ -304,7 +303,7 @@ static int cpufreq_exit(struct cpufreq_policy *policy) dev_pm_opp_free_cpufreq_table(priv->cpu_dev, &policy->freq_table); dev_pm_opp_of_cpumask_remove_table(policy->related_cpus); if (priv->reg_name) - dev_pm_opp_put_regulator(priv->opp_table); + dev_pm_opp_put_regulators(priv->cpu_dev); clk_put(policy->clk); kfree(priv); diff --git b/drivers/cpufreq/ti-cpufreq.c b/drivers/cpufreq/ti-cpufreq.c new file mode 100644 index 000000000..afbaef967 --- /dev/null +++ b/drivers/cpufreq/ti-cpufreq.c @@ -0,0 +1,288 @@ +/* + * TI CPUFreq/OPP hw-supported driver + * + * Copyright (C) 2016 Texas Instruments, Inc. + * Dave Gerlach + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * version 2 as published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#define REVISION_MASK 0xF +#define REVISION_SHIFT 28 + +#define AM33XX_800M_ARM_MPU_MAX_FREQ 0x1E2F +#define AM43XX_600M_ARM_MPU_MAX_FREQ 0xFFA + +#define DRA7_EFUSE_HAS_OD_MPU_OPP 11 +#define DRA7_EFUSE_HAS_HIGH_MPU_OPP 15 +#define DRA7_EFUSE_HAS_ALL_MPU_OPP 23 + +#define DRA7_EFUSE_NOM_MPU_OPP BIT(0) +#define DRA7_EFUSE_OD_MPU_OPP BIT(1) +#define DRA7_EFUSE_HIGH_MPU_OPP BIT(2) + +#define VERSION_COUNT 2 + +struct ti_cpufreq_data; + +struct ti_cpufreq_soc_data { + unsigned long (*efuse_xlate)(struct ti_cpufreq_data *opp_data, + unsigned long efuse); + unsigned long efuse_fallback; +}; + +struct ti_cpufreq_data { + struct device *cpu_dev; + struct device_node *opp_node; + struct regmap *opp_efuse; + struct regmap *revision; + const struct ti_cpufreq_soc_data *soc_data; +}; + +static unsigned long amx3_efuse_xlate(struct ti_cpufreq_data *opp_data, + unsigned long efuse) +{ + if (!efuse) + efuse = opp_data->soc_data->efuse_fallback; + /* AM335x and AM437x use "OPP disable" bits, so invert */ + return ~efuse; +} + +static unsigned long dra7_efuse_xlate(struct ti_cpufreq_data *opp_data, + unsigned long efuse) +{ + unsigned long calculated_efuse = DRA7_EFUSE_NOM_MPU_OPP; + + /* + * The efuse on dra7 and am57 parts contains a specific + * value indicating the highest available OPP. + */ + + switch (efuse) { + case DRA7_EFUSE_HAS_ALL_MPU_OPP: + case DRA7_EFUSE_HAS_HIGH_MPU_OPP: + calculated_efuse |= DRA7_EFUSE_HIGH_MPU_OPP; + case DRA7_EFUSE_HAS_OD_MPU_OPP: + calculated_efuse |= DRA7_EFUSE_OD_MPU_OPP; + } + + return calculated_efuse; +} + +static struct ti_cpufreq_soc_data am3x_soc_data = { + .efuse_xlate = amx3_efuse_xlate, + .efuse_fallback = AM33XX_800M_ARM_MPU_MAX_FREQ, +}; + +static struct ti_cpufreq_soc_data am4x_soc_data = { + .efuse_xlate = amx3_efuse_xlate, + .efuse_fallback = AM43XX_600M_ARM_MPU_MAX_FREQ, +}; + +static struct ti_cpufreq_soc_data dra7_soc_data = { + .efuse_xlate = dra7_efuse_xlate, +}; + +/** + * ti_cpufreq_get_efuse() - Parse and return efuse value present on SoC + * @opp_data: pointer to ti_cpufreq_data context + * @efuse_value: Set to the value parsed from efuse + * + * Returns error code if efuse not read properly. + */ +static int ti_cpufreq_get_efuse(struct ti_cpufreq_data *opp_data, + u32 *efuse_value) +{ + struct device *dev = opp_data->cpu_dev; + struct device_node *np = opp_data->opp_node; + unsigned int efuse_offset; + u32 efuse, efuse_mask, efuse_shift, vals[4]; + int ret; + + ret = of_property_read_u32_array(np, "ti,syscon-efuse", vals, 4); + if (ret) { + dev_err(dev, "ti,syscon-efuse cannot be read %s: %d\n", + np->full_name, ret); + return ret; + } + + efuse_offset = vals[1]; + efuse_mask = vals[2]; + efuse_shift = vals[3]; + + ret = regmap_read(opp_data->opp_efuse, efuse_offset, &efuse); + if (ret) { + dev_err(dev, + "Failed to read the efuse value from syscon: %d\n", + ret); + return ret; + } + + efuse = (efuse & efuse_mask) >> efuse_shift; + + *efuse_value = opp_data->soc_data->efuse_xlate(opp_data, efuse); + + return 0; +} + +/** + * ti_cpufreq_get_rev() - Parse and return rev value present on SoC + * @opp_data: pointer to ti_cpufreq_data context + * @revision_value: Set to the value parsed from revision register + * + * Returns error code if revision not read properly. + */ +static int ti_cpufreq_get_rev(struct ti_cpufreq_data *opp_data, + u32 *revision_value) +{ + struct device *dev = opp_data->cpu_dev; + struct device_node *np = opp_data->opp_node; + unsigned int revision_offset; + u32 revision; + int ret; + + ret = of_property_read_u32_index(np, "ti,syscon-rev", + 1, &revision_offset); + if (ret) { + dev_err(dev, + "No revision offset provided %s [%d]\n", + np->full_name, ret); + return ret; + } + + ret = regmap_read(opp_data->revision, revision_offset, &revision); + if (ret) { + dev_err(dev, + "Failed to read the revision number from syscon: %d\n", + ret); + return ret; + } + + *revision_value = BIT((revision >> REVISION_SHIFT) & REVISION_MASK); + + return 0; +} + +static int ti_cpufreq_setup_syscon_registers(struct ti_cpufreq_data *opp_data) +{ + struct device *dev = opp_data->cpu_dev; + struct device_node *np = opp_data->opp_node; + + opp_data->opp_efuse = syscon_regmap_lookup_by_phandle(np, + "ti,syscon-efuse"); + if (IS_ERR(opp_data->opp_efuse)) { + dev_err(dev, + "\"ti,syscon-efuse\" is missing, cannot use OPPv2 table.\n"); + return PTR_ERR(opp_data->opp_efuse); + } + + opp_data->revision = syscon_regmap_lookup_by_phandle(np, + "ti,syscon-rev"); + if (IS_ERR(opp_data->revision)) { + dev_err(dev, + "\"ti,syscon-rev\" is missing, cannot use OPPv2 table.\n"); + return PTR_ERR(opp_data->revision); + } + + return 0; +} + +static const struct of_device_id ti_cpufreq_of_match[] = { + { .compatible = "ti,am33xx", .data = &am3x_soc_data, }, + { .compatible = "ti,am4372", .data = &am4x_soc_data, }, + { .compatible = "ti,dra7", .data = &dra7_soc_data }, + {}, +}; + +static int ti_cpufreq_init(void) +{ + u32 version[VERSION_COUNT]; + struct device_node *np; + const struct of_device_id *match; + struct ti_cpufreq_data *opp_data; + int ret; + + np = of_find_node_by_path("/"); + match = of_match_node(ti_cpufreq_of_match, np); + if (!match) + return -ENODEV; + + opp_data = kzalloc(sizeof(*opp_data), GFP_KERNEL); + if (!opp_data) + return -ENOMEM; + + opp_data->soc_data = match->data; + + opp_data->cpu_dev = get_cpu_device(0); + if (!opp_data->cpu_dev) { + pr_err("%s: Failed to get device for CPU0\n", __func__); + return -ENODEV; + } + + opp_data->opp_node = dev_pm_opp_of_get_opp_desc_node(opp_data->cpu_dev); + if (!opp_data->opp_node) { + dev_info(opp_data->cpu_dev, + "OPP-v2 not supported, cpufreq-dt will attempt to use legacy tables.\n"); + goto register_cpufreq_dt; + } + + ret = ti_cpufreq_setup_syscon_registers(opp_data); + if (ret) + goto fail_put_node; + + /* + * OPPs determine whether or not they are supported based on + * two metrics: + * 0 - SoC Revision + * 1 - eFuse value + */ + ret = ti_cpufreq_get_rev(opp_data, &version[0]); + if (ret) + goto fail_put_node; + + ret = ti_cpufreq_get_efuse(opp_data, &version[1]); + if (ret) + goto fail_put_node; + + of_node_put(opp_data->opp_node); + + ret = dev_pm_opp_set_supported_hw(opp_data->cpu_dev, version, + VERSION_COUNT); + if (ret) { + dev_err(opp_data->cpu_dev, + "Failed to set supported hardware\n"); + goto fail_put_node; + } + +register_cpufreq_dt: + platform_device_register_simple("cpufreq-dt", -1, NULL, 0); + + return 0; + +fail_put_node: + of_node_put(opp_data->opp_node); + + return ret; +} +module_init(ti_cpufreq_init); + +MODULE_DESCRIPTION("TI CPUFreq/OPP hw-supported driver"); +MODULE_AUTHOR("Dave Gerlach "); +MODULE_LICENSE("GPL v2"); diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig index ed37e5908..a118ef6bb 100644 --- a/drivers/gpio/Kconfig +++ b/drivers/gpio/Kconfig @@ -61,6 +61,20 @@ config GPIO_SYSFS Kernel drivers may also request that a particular GPIO be exported to userspace; this can be useful when debugging. +config GPIO_OF_HELPER + bool "GPIO OF helper device (EXPERIMENTAL)" + depends on OF_GPIO + help + Say Y here to add an GPIO OF helper driver + + Allows you specify a GPIO helper based on OF + which allows simple export of GPIO functionality + in user-space. + + Features include, value set/get, direction control, + interrupt/value change poll support, event counting + and others. + config GPIO_GENERIC depends on HAS_IOMEM # Only for IOMEM drivers tristate diff --git a/drivers/gpio/Makefile b/drivers/gpio/Makefile index d074c2299..e4e13b827 100644 --- a/drivers/gpio/Makefile +++ b/drivers/gpio/Makefile @@ -8,6 +8,7 @@ obj-$(CONFIG_GPIOLIB) += gpiolib-legacy.o obj-$(CONFIG_OF_GPIO) += gpiolib-of.o obj-$(CONFIG_GPIO_SYSFS) += gpiolib-sysfs.o obj-$(CONFIG_GPIO_ACPI) += gpiolib-acpi.o +obj-$(CONFIG_GPIO_OF_HELPER) += gpio-of-helper.o # Device drivers. Generally keep list sorted alphabetically obj-$(CONFIG_GPIO_GENERIC) += gpio-generic.o diff --git b/drivers/gpio/gpio-of-helper.c b/drivers/gpio/gpio-of-helper.c new file mode 100644 index 000000000..83f362f7d --- /dev/null +++ b/drivers/gpio/gpio-of-helper.c @@ -0,0 +1,435 @@ +/* + * GPIO OF based helper + * + * A simple DT based driver to provide access to GPIO functionality + * to user-space via sysfs. + * + * Copyright (C) 2013 Pantelis Antoniou + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +/* fwd decl. */ +struct gpio_of_helper_info; + +enum gpio_type { + GPIO_TYPE_INPUT = 0, + GPIO_TYPE_OUTPUT = 1, +}; + +struct gpio_of_entry { + int id; + struct gpio_of_helper_info *info; + struct device_node *node; + enum gpio_type type; + int gpio; + int irq; + const char *name; + atomic64_t counter; + unsigned int count_flags; +#define COUNT_RISING_EDGE (1 << 0) +#define COUNT_FALLING_EDGE (1 << 1) +}; + +struct gpio_of_helper_info { + struct platform_device *pdev; + struct idr idr; +}; + +static const struct of_device_id gpio_of_helper_of_match[] = { + { + .compatible = "gpio-of-helper", + }, + { }, +}; +MODULE_DEVICE_TABLE(of, gpio_of_helper_of_match); + +static ssize_t gpio_of_helper_show_status(struct device *dev, + struct device_attribute *attr, char *buf) +{ + struct platform_device *pdev = to_platform_device(dev); + struct gpio_of_helper_info *info = platform_get_drvdata(pdev); + struct gpio_of_entry *entry; + char *p, *e; + int id, n; + + p = buf; + e = p + PAGE_SIZE; + n = 0; + idr_for_each_entry(&info->idr, entry, id) { + switch (entry->type) { + case GPIO_TYPE_INPUT: + n = snprintf(p, e - p, "%2d %-24s %3d %-3s %llu\n", + entry->id, entry->name, entry->gpio, "IN", + (unsigned long long) + atomic64_read(&entry->counter)); + break; + case GPIO_TYPE_OUTPUT: + n = snprintf(p, e - p, "%2d %-24s %3d %-3s\n", + entry->id, entry->name, entry->gpio, "OUT"); + break; + } + p += n; + } + + return p - buf; +} + +static DEVICE_ATTR(status, S_IRUGO, + gpio_of_helper_show_status, NULL); + +static irqreturn_t gpio_of_helper_handler(int irq, void *ptr) +{ + struct gpio_of_entry *entry = ptr; + + /* caution - low speed interfaces only! */ + atomic64_inc(&entry->counter); + + return IRQ_HANDLED; +} + +static struct gpio_of_entry * +gpio_of_entry_create(struct gpio_of_helper_info *info, + struct device_node *node) +{ + struct platform_device *pdev = info->pdev; + struct device *dev = &pdev->dev; + struct gpio_of_entry *entry; + int err, gpio, irq; + unsigned int req_flags, count_flags, irq_flags; + enum gpio_type type; + enum of_gpio_flags gpio_flags; + const char *name; + + /* get the type of the node first */ + if (of_property_read_bool(node, "input")) + type = GPIO_TYPE_INPUT; + else if (of_property_read_bool(node, "output") + || of_property_read_bool(node, "init-low") + || of_property_read_bool(node, "init-high")) + type = GPIO_TYPE_OUTPUT; + else { + dev_err(dev, "Not valid gpio node type\n"); + err = -EINVAL; + goto err_bad_node; + } + + /* get the name */ + if (of_property_read_string(node, "line-name", &name)) + if (of_property_read_string(node, "gpio-name", &name)) + name = node->name; + + err = of_get_named_gpio_flags(node, "gpio", 0, &gpio_flags); + if (IS_ERR_VALUE(err)) { + dev_err(dev, "Failed to get gpio property of '%s'\n", name); + goto err_bad_node; + } + gpio = err; + + req_flags = 0; + count_flags = 0; + + /* set the request flags */ + switch (type) { + case GPIO_TYPE_INPUT: + req_flags = GPIOF_DIR_IN | GPIOF_EXPORT; + if (of_property_read_bool(node, "count-falling-edge")) + count_flags |= COUNT_FALLING_EDGE; + if (of_property_read_bool(node, "count-rising-edge")) + count_flags |= COUNT_RISING_EDGE; + break; + case GPIO_TYPE_OUTPUT: + req_flags = GPIOF_DIR_OUT | GPIOF_EXPORT; + if (of_property_read_bool(node, "init-high")) + req_flags |= GPIOF_OUT_INIT_HIGH; + else if (of_property_read_bool(node, "init-low")) + req_flags |= GPIOF_OUT_INIT_LOW; + break; + } + if (of_property_read_bool(node, "dir-changeable")) + req_flags |= GPIOF_EXPORT_CHANGEABLE; + if (gpio_flags & OF_GPIO_ACTIVE_LOW) + req_flags |= GPIOF_ACTIVE_LOW; + if (gpio_flags & OF_GPIO_SINGLE_ENDED) { + if (gpio_flags & OF_GPIO_ACTIVE_LOW) + req_flags |= GPIOF_OPEN_DRAIN; + else + req_flags |= GPIOF_OPEN_SOURCE; + } + + /* request the gpio */ + err = devm_gpio_request_one(dev, gpio, req_flags, name); + if (err != 0) { + dev_err(dev, "Failed to request gpio '%s'\n", name); + goto err_bad_node; + } + + irq = -1; + irq_flags = 0; + + /* counter mode requested - need an interrupt */ + if (count_flags != 0) { + irq = gpio_to_irq(gpio); + if (IS_ERR_VALUE(irq)) { + dev_err(dev, "Failed to request gpio '%s'\n", name); + goto err_bad_node; + } + + if (count_flags & COUNT_RISING_EDGE) + irq_flags |= IRQF_TRIGGER_RISING; + if (count_flags & COUNT_FALLING_EDGE) + irq_flags |= IRQF_TRIGGER_FALLING; + } + +// if (!idr_pre_get(&info->idr, GFP_KERNEL)) { +// dev_err(dev, "Failed on idr_pre_get of '%s'\n", name); +// err = -ENOMEM; +// goto err_no_mem; +// } + + idr_preload(GFP_KERNEL); + + entry = devm_kzalloc(dev, sizeof(*entry), GFP_KERNEL); + if (entry == NULL) { + dev_err(dev, "Failed to allocate gpio entry of '%s'\n", name); + err = -ENOMEM; + goto err_no_mem; + } + + entry->id = -1; + entry->info = info; + entry->node = of_node_get(node); /* get node reference */ + entry->type = type; + entry->gpio = gpio; + entry->irq = irq; + entry->name = name; + + /* interrupt enable is last thing done */ + if (irq >= 0) { + atomic64_set(&entry->counter, 0); + entry->count_flags = count_flags; + err = devm_request_irq(dev, irq, gpio_of_helper_handler, + irq_flags, name, entry); + if (err != 0) { + dev_err(dev, "Failed to request irq of '%s'\n", name); + goto err_no_irq; + } + } + + /* all done; insert */ +// err = idr_get_new(&info->idr, entry, &entry->id); +// if (IS_ERR_VALUE(err)) { +// dev_err(dev, "Failed to idr_get_new of '%s'\n", name); +// goto err_fail_idr; +// } + + err = idr_alloc(&info->idr, entry, 0, 0, GFP_NOWAIT); + if (err >= 0) + entry->id = err; + + idr_preload_end(); + + if (err < 0) { + dev_err(dev, "Failed to idr_get_new of '%s'\n", name); + goto err_fail_idr; + } + + dev_dbg(dev, "Allocated GPIO id=%d name='%s'\n", entry->id, name); + + return entry; + +err_fail_idr: + /* nothing to do */ +err_no_irq: + /* release node ref */ + of_node_put(node); + /* nothing else needs to be done, devres handles it */ +err_no_mem: +err_bad_node: + return ERR_PTR(err); +} + +static int gpio_of_entry_destroy(struct gpio_of_entry *entry) +{ + struct gpio_of_helper_info *info = entry->info; + struct platform_device *pdev = info->pdev; + struct device *dev = &pdev->dev; + + dev_dbg(dev, "Destroying GPIO id=%d\n", entry->id); + + /* remove from the IDR */ + idr_remove(&info->idr, entry->id); + + /* remove node ref */ + of_node_put(entry->node); + + /* free gpio */ + devm_gpio_free(dev, entry->gpio); + + /* gree irq */ + if (entry->irq >= 0) + devm_free_irq(dev, entry->irq, entry); + + /* and free */ + devm_kfree(dev, entry); + + return 0; +} + +static int gpio_of_helper_probe(struct platform_device *pdev) +{ + struct device *dev = &pdev->dev; + struct gpio_of_helper_info *info; + struct gpio_of_entry *entry; + struct device_node *pnode = pdev->dev.of_node; + struct device_node *cnode; + struct pinctrl *pinctrl; + int err; + + /* we only support OF */ + if (pnode == NULL) { + dev_err(&pdev->dev, "No platform of_node!\n"); + return -ENODEV; + } + + pinctrl = devm_pinctrl_get_select_default(&pdev->dev); + if (IS_ERR(pinctrl)) { + /* special handling for probe defer */ + if (PTR_ERR(pinctrl) == -EPROBE_DEFER) + return -EPROBE_DEFER; + + dev_warn(&pdev->dev, + "pins are not configured from the driver\n"); + } + + info = devm_kzalloc(&pdev->dev, sizeof(*info), GFP_KERNEL); + if (info == NULL) { + dev_err(&pdev->dev, "Failed to allocate info\n"); + err = -ENOMEM; + goto err_no_mem; + } + platform_set_drvdata(pdev, info); + info->pdev = pdev; + + idr_init(&info->idr); + + err = device_create_file(dev, &dev_attr_status); + if (err != 0) { + dev_err(dev, "Failed to create status sysfs attribute\n"); + goto err_no_sysfs; + } + + for_each_child_of_node(pnode, cnode) { + + entry = gpio_of_entry_create(info, cnode); + if (IS_ERR_OR_NULL(entry)) { + dev_err(dev, "Failed to create gpio entry\n"); + err = PTR_ERR(entry); + goto err_fail_entry; + } + } + + dev_info(&pdev->dev, "ready\n"); + + return 0; +err_fail_entry: + device_remove_file(&pdev->dev, &dev_attr_status); +err_no_sysfs: +err_no_mem: + return err; +} + +static int gpio_of_helper_remove(struct platform_device *pdev) +{ + struct gpio_of_helper_info *info = platform_get_drvdata(pdev); + struct gpio_of_entry *entry; + int id; + + dev_info(&pdev->dev, "removing\n"); + + device_remove_file(&pdev->dev, &dev_attr_status); + + id = 0; + idr_for_each_entry(&info->idr, entry, id) { + /* destroy each and every one */ + gpio_of_entry_destroy(entry); + } + + return 0; +} + +#ifdef CONFIG_PM +//#ifdef CONFIG_PM_RUNTIME +static int gpio_of_helper_runtime_suspend(struct device *dev) +{ + /* place holder */ + return 0; +} + +static int gpio_of_helper_runtime_resume(struct device *dev) +{ + /* place holder */ + return 0; +} +//#endif /* CONFIG_PM_RUNTIME */ + +static struct dev_pm_ops gpio_of_helper_pm_ops = { + SET_RUNTIME_PM_OPS(gpio_of_helper_runtime_suspend, + gpio_of_helper_runtime_resume, NULL) +}; +#define GPIO_OF_HELPER_PM_OPS (&gpio_of_helper_pm_ops) +#else +#define GPIO_OF_HELPER_PM_OPS NULL +#endif /* CONFIG_PM */ + +struct platform_driver gpio_of_helper_driver = { + .probe = gpio_of_helper_probe, + .remove = gpio_of_helper_remove, + .driver = { + .name = "gpio-of-helper", + .owner = THIS_MODULE, + .pm = GPIO_OF_HELPER_PM_OPS, + .of_match_table = gpio_of_helper_of_match, + }, +}; + +module_platform_driver(gpio_of_helper_driver); + +MODULE_AUTHOR("Pantelis Antoniou "); +MODULE_DESCRIPTION("GPIO OF Helper driver"); +MODULE_LICENSE("GPL"); +MODULE_ALIAS("platform:gpio-of-helper"); diff --git a/drivers/gpio/gpiolib-sysfs.c b/drivers/gpio/gpiolib-sysfs.c index 4b44dd97c..9c6de282d 100644 --- a/drivers/gpio/gpiolib-sysfs.c +++ b/drivers/gpio/gpiolib-sysfs.c @@ -35,10 +35,10 @@ static DEFINE_MUTEX(sysfs_lock); /* * /sys/class/gpio/gpioN... only for GPIOs that are exported * /direction - * * MAY BE OMITTED if kernel won't allow direction changes * * is read/write as "in" or "out" * * may also be written as "high" or "low", initializing * output value as specified ("out" implies "low") + * * read-only if kernel won't allow direction changes * /value * * always readable, subject to hardware behavior * * may be writable, as zero/nonzero @@ -51,6 +51,8 @@ static DEFINE_MUTEX(sysfs_lock); * * is read/write as zero/nonzero * * also affects existing and subsequent "falling" and "rising" * /edge configuration + * /label + * * descriptor label */ static ssize_t direction_show(struct device *dev, @@ -81,7 +83,9 @@ static ssize_t direction_store(struct device *dev, mutex_lock(&data->mutex); - if (sysfs_streq(buf, "high")) + if (!data->direction_can_change) + status = -EPERM; + else if (sysfs_streq(buf, "high")) status = gpiod_direction_output_raw(desc, 1); else if (sysfs_streq(buf, "out") || sysfs_streq(buf, "low")) status = gpiod_direction_output_raw(desc, 0); @@ -350,6 +354,23 @@ static ssize_t active_low_store(struct device *dev, } static DEVICE_ATTR_RW(active_low); +static ssize_t label_show(struct device *dev, + struct device_attribute *attr, char *buf) +{ + struct gpiod_data *data = dev_get_drvdata(dev); + struct gpio_desc *desc = data->desc; + ssize_t status; + + mutex_lock(&data->mutex); + + status = sprintf(buf, "%s\n", desc->label); + + mutex_unlock(&data->mutex); + + return status; +} +static DEVICE_ATTR_RO(label); + static umode_t gpio_is_visible(struct kobject *kobj, struct attribute *attr, int n) { @@ -361,12 +382,15 @@ static umode_t gpio_is_visible(struct kobject *kobj, struct attribute *attr, if (attr == &dev_attr_direction.attr) { if (!show_direction) - mode = 0; + mode &= 0444; } else if (attr == &dev_attr_edge.attr) { if (gpiod_to_irq(desc) < 0) mode = 0; if (!show_direction && test_bit(FLAG_IS_OUT, &desc->flags)) mode = 0; + } else if (attr == &dev_attr_value.attr) { + if (!show_direction && !test_bit(FLAG_IS_OUT, &desc->flags)) + mode &= 0444; } return mode; @@ -377,6 +401,7 @@ static struct attribute *gpio_attrs[] = { &dev_attr_edge.attr, &dev_attr_value.attr, &dev_attr_active_low.attr, + &dev_attr_label.attr, NULL, }; @@ -390,6 +415,10 @@ static const struct attribute_group *gpio_groups[] = { NULL }; +/* bwlegh, a second device in the same file... get out of my namespace! */ +#define dev_attr_label dev_attr_chip_label +#define label_show chip_label_show + /* * /sys/class/gpio/gpiochipN/ * /base ... matching gpio_chip.base (N) diff --git a/drivers/gpu/drm/Kconfig b/drivers/gpu/drm/Kconfig index 483059a22..c882d09d8 100644 --- a/drivers/gpu/drm/Kconfig +++ b/drivers/gpu/drm/Kconfig @@ -300,3 +300,4 @@ config DRM_SAVAGE chipset. If M is selected the module will be called savage. endif # DRM_LEGACY +source "drivers/gpu/drm/tinydrm/Kconfig" diff --git a/drivers/gpu/drm/Makefile b/drivers/gpu/drm/Makefile index 25c720454..11c4b8e7e 100644 --- a/drivers/gpu/drm/Makefile +++ b/drivers/gpu/drm/Makefile @@ -86,3 +86,4 @@ obj-$(CONFIG_DRM_FSL_DCU) += fsl-dcu/ obj-$(CONFIG_DRM_ETNAVIV) += etnaviv/ obj-$(CONFIG_DRM_ARCPGU)+= arc/ obj-y += hisilicon/ +obj-$(CONFIG_DRM_TINYDRM)+= tinydrm/ diff --git a/drivers/gpu/drm/etnaviv/Kconfig b/drivers/gpu/drm/etnaviv/Kconfig index 2cde7a544..b776f41e8 100644 --- a/drivers/gpu/drm/etnaviv/Kconfig +++ b/drivers/gpu/drm/etnaviv/Kconfig @@ -2,7 +2,7 @@ config DRM_ETNAVIV tristate "ETNAVIV (DRM support for Vivante GPU IP cores)" depends on DRM - depends on ARCH_MXC || ARCH_DOVE + depends on ARCH_MXC || ARCH_DOVE || ARCH_OMAP2PLUS select SHMEM select TMPFS select IOMMU_API diff --git a/drivers/gpu/drm/etnaviv/etnaviv_drv.c b/drivers/gpu/drm/etnaviv/etnaviv_drv.c index aa687669e..20d20cad2 100644 --- a/drivers/gpu/drm/etnaviv/etnaviv_drv.c +++ b/drivers/gpu/drm/etnaviv/etnaviv_drv.c @@ -654,6 +654,7 @@ static int etnaviv_pdev_remove(struct platform_device *pdev) static const struct of_device_id dt_match[] = { { .compatible = "fsl,imx-gpu-subsystem" }, { .compatible = "marvell,dove-gpu-subsystem" }, + { .compatible = "vivante,gc-gpu-subsystem"}, {} }; MODULE_DEVICE_TABLE(of, dt_match); diff --git a/drivers/gpu/drm/i2c/Kconfig b/drivers/gpu/drm/i2c/Kconfig index a6c92beb4..66ff8e3f7 100644 --- a/drivers/gpu/drm/i2c/Kconfig +++ b/drivers/gpu/drm/i2c/Kconfig @@ -1,6 +1,12 @@ menu "I2C encoder or helper chips" depends on DRM && DRM_KMS_HELPER && I2C +config DRM_I2C_ADIHDMI + tristate "ADI HDMI encoder" + default m if DRM_TILCDC + help + Support for ADI HDMI encoder. + config DRM_I2C_CH7006 tristate "Chrontel ch7006 TV encoder" default m if DRM_NOUVEAU diff --git a/drivers/gpu/drm/i2c/Makefile b/drivers/gpu/drm/i2c/Makefile index 43aa33bae..62a4eea42 100644 --- a/drivers/gpu/drm/i2c/Makefile +++ b/drivers/gpu/drm/i2c/Makefile @@ -8,3 +8,6 @@ obj-$(CONFIG_DRM_I2C_SIL164) += sil164.o tda998x-y := tda998x_drv.o obj-$(CONFIG_DRM_I2C_NXP_TDA998X) += tda998x.o + +adihdmi-y := adihdmi_drv.o +obj-$(CONFIG_DRM_I2C_ADIHDMI) += adihdmi.o diff --git b/drivers/gpu/drm/i2c/adihdmi.h b/drivers/gpu/drm/i2c/adihdmi.h new file mode 100644 index 000000000..58d9a2b27 --- /dev/null +++ b/drivers/gpu/drm/i2c/adihdmi.h @@ -0,0 +1,289 @@ +/* + * Analog Devices ADIHDMI HDMI transmitter driver + * + * Copyright 2012 Analog Devices Inc. + * + * Licensed under the GPL-2. + */ + +#ifndef __DRM_I2C_ADIHDMI_H__ +#define __DRM_I2C_ADIHDMI_H__ + +#include + +#define ADIHDMI_REG_CHIP_REVISION 0x00 +#define ADIHDMI_REG_N0 0x01 +#define ADIHDMI_REG_N1 0x02 +#define ADIHDMI_REG_N2 0x03 +#define ADIHDMI_REG_SPDIF_FREQ 0x04 +#define ADIHDMI_REG_CTS_AUTOMATIC1 0x05 +#define ADIHDMI_REG_CTS_AUTOMATIC2 0x06 +#define ADIHDMI_REG_CTS_MANUAL0 0x07 +#define ADIHDMI_REG_CTS_MANUAL1 0x08 +#define ADIHDMI_REG_CTS_MANUAL2 0x09 +#define ADIHDMI_REG_AUDIO_SOURCE 0x0a +#define ADIHDMI_REG_AUDIO_CONFIG 0x0b +#define ADIHDMI_REG_I2S_CONFIG 0x0c +#define ADIHDMI_REG_I2S_WIDTH 0x0d +#define ADIHDMI_REG_AUDIO_SUB_SRC0 0x0e +#define ADIHDMI_REG_AUDIO_SUB_SRC1 0x0f +#define ADIHDMI_REG_AUDIO_SUB_SRC2 0x10 +#define ADIHDMI_REG_AUDIO_SUB_SRC3 0x11 +#define ADIHDMI_REG_AUDIO_CFG1 0x12 +#define ADIHDMI_REG_AUDIO_CFG2 0x13 +#define ADIHDMI_REG_AUDIO_CFG3 0x14 +#define ADIHDMI_REG_I2C_FREQ_ID_CFG 0x15 +#define ADIHDMI_REG_VIDEO_INPUT_CFG1 0x16 +#define ADIHDMI_REG_CSC_UPPER(x) (0x18 + (x) * 2) +#define ADIHDMI_REG_CSC_LOWER(x) (0x19 + (x) * 2) +#define ADIHDMI_REG_SYNC_DECODER(x) (0x30 + (x)) +#define ADIHDMI_REG_DE_GENERATOR (0x35 + (x)) +#define ADIHDMI_REG_PIXEL_REPETITION 0x3b +#define ADIHDMI_REG_VIC_MANUAL 0x3c +#define ADIHDMI_REG_VIC_SEND 0x3d +#define ADIHDMI_REG_VIC_DETECTED 0x3e +#define ADIHDMI_REG_AUX_VIC_DETECTED 0x3f +#define ADIHDMI_REG_PACKET_ENABLE0 0x40 +#define ADIHDMI_REG_POWER 0x41 +#define ADIHDMI_REG_STATUS 0x42 +#define ADIHDMI_REG_EDID_I2C_ADDR 0x43 +#define ADIHDMI_REG_PACKET_ENABLE1 0x44 +#define ADIHDMI_REG_PACKET_I2C_ADDR 0x45 +#define ADIHDMI_REG_DSD_ENABLE 0x46 +#define ADIHDMI_REG_VIDEO_INPUT_CFG2 0x48 +#define ADIHDMI_REG_INFOFRAME_UPDATE 0x4a +#define ADIHDMI_REG_GC(x) (0x4b + (x)) /* 0x4b - 0x51 */ +#define ADIHDMI_REG_AVI_INFOFRAME_VERSION 0x52 +#define ADIHDMI_REG_AVI_INFOFRAME_LENGTH 0x53 +#define ADIHDMI_REG_AVI_INFOFRAME_CHECKSUM 0x54 +#define ADIHDMI_REG_AVI_INFOFRAME(x) (0x55 + (x)) /* 0x55 - 0x6f */ +#define ADIHDMI_REG_AUDIO_INFOFRAME_VERSION 0x70 +#define ADIHDMI_REG_AUDIO_INFOFRAME_LENGTH 0x71 +#define ADIHDMI_REG_AUDIO_INFOFRAME_CHECKSUM 0x72 +#define ADIHDMI_REG_AUDIO_INFOFRAME(x) (0x73 + (x)) /* 0x73 - 0x7c */ +#define ADIHDMI_REG_INT_ENABLE(x) (0x94 + (x)) +#define ADIHDMI_REG_INT(x) (0x96 + (x)) +#define ADIHDMI_REG_INPUT_CLK_DIV 0x9d +#define ADIHDMI_REG_PLL_STATUS 0x9e +#define ADIHDMI_REG_HDMI_POWER 0xa1 +#define ADIHDMI_REG_HDCP_HDMI_CFG 0xaf +#define ADIHDMI_REG_AN(x) (0xb0 + (x)) /* 0xb0 - 0xb7 */ +#define ADIHDMI_REG_HDCP_STATUS 0xb8 +#define ADIHDMI_REG_BCAPS 0xbe +#define ADIHDMI_REG_BKSV(x) (0xc0 + (x)) /* 0xc0 - 0xc3 */ +#define ADIHDMI_REG_EDID_SEGMENT 0xc4 +#define ADIHDMI_REG_DDC_STATUS 0xc8 +#define ADIHDMI_REG_EDID_READ_CTRL 0xc9 +#define ADIHDMI_REG_BSTATUS(x) (0xca + (x)) /* 0xca - 0xcb */ +#define ADIHDMI_REG_TIMING_GEN_SEQ 0xd0 +#define ADIHDMI_REG_POWER2 0xd6 +#define ADIHDMI_REG_HSYNC_PLACEMENT_MSB 0xfa + +#define ADIHDMI_REG_SYNC_ADJUSTMENT(x) (0xd7 + (x)) /* 0xd7 - 0xdc */ +#define ADIHDMI_REG_TMDS_CLOCK_INV 0xde +#define ADIHDMI_REG_ARC_CTRL 0xdf +#define ADIHDMI_REG_CEC_I2C_ADDR 0xe1 +#define ADIHDMI_REG_CEC_CTRL 0xe2 +#define ADIHDMI_REG_CHIP_ID_HIGH 0xf5 +#define ADIHDMI_REG_CHIP_ID_LOW 0xf6 + +#define ADIHDMI_CSC_ENABLE BIT(7) +#define ADIHDMI_CSC_UPDATE_MODE BIT(5) + +#define ADIHDMI_INT0_HDP BIT(7) +#define ADIHDMI_INT0_VSYNC BIT(5) +#define ADIHDMI_INT0_AUDIO_FIFO_FULL BIT(4) +#define ADIHDMI_INT0_EDID_READY BIT(2) +#define ADIHDMI_INT0_HDCP_AUTHENTICATED BIT(1) + +#define ADIHDMI_INT1_DDC_ERROR BIT(7) +#define ADIHDMI_INT1_BKSV BIT(6) +#define ADIHDMI_INT1_CEC_TX_READY BIT(5) +#define ADIHDMI_INT1_CEC_TX_ARBIT_LOST BIT(4) +#define ADIHDMI_INT1_CEC_TX_RETRY_TIMEOUT BIT(3) +#define ADIHDMI_INT1_CEC_RX_READY3 BIT(2) +#define ADIHDMI_INT1_CEC_RX_READY2 BIT(1) +#define ADIHDMI_INT1_CEC_RX_READY1 BIT(0) + +#define ADIHDMI_ARC_CTRL_POWER_DOWN BIT(0) + +#define ADIHDMI_CEC_CTRL_POWER_DOWN BIT(0) + +#define ADIHDMI_POWER_POWER_DOWN BIT(6) + +#define ADIHDMI_HDMI_CFG_MODE_MASK 0x2 +#define ADIHDMI_HDMI_CFG_MODE_DVI 0x0 +#define ADIHDMI_HDMI_CFG_MODE_HDMI 0x2 + +#define ADIHDMI_AUDIO_SELECT_I2C 0x0 +#define ADIHDMI_AUDIO_SELECT_SPDIF 0x1 +#define ADIHDMI_AUDIO_SELECT_DSD 0x2 +#define ADIHDMI_AUDIO_SELECT_HBR 0x3 +#define ADIHDMI_AUDIO_SELECT_DST 0x4 + +#define ADIHDMI_I2S_SAMPLE_LEN_16 0x2 +#define ADIHDMI_I2S_SAMPLE_LEN_20 0x3 +#define ADIHDMI_I2S_SAMPLE_LEN_18 0x4 +#define ADIHDMI_I2S_SAMPLE_LEN_22 0x5 +#define ADIHDMI_I2S_SAMPLE_LEN_19 0x8 +#define ADIHDMI_I2S_SAMPLE_LEN_23 0x9 +#define ADIHDMI_I2S_SAMPLE_LEN_24 0xb +#define ADIHDMI_I2S_SAMPLE_LEN_17 0xc +#define ADIHDMI_I2S_SAMPLE_LEN_21 0xd + +#define ADIHDMI_SAMPLE_FREQ_44100 0x0 +#define ADIHDMI_SAMPLE_FREQ_48000 0x2 +#define ADIHDMI_SAMPLE_FREQ_32000 0x3 +#define ADIHDMI_SAMPLE_FREQ_88200 0x8 +#define ADIHDMI_SAMPLE_FREQ_96000 0xa +#define ADIHDMI_SAMPLE_FREQ_176400 0xc +#define ADIHDMI_SAMPLE_FREQ_192000 0xe + +#define ADIHDMI_STATUS_POWER_DOWN_POLARITY BIT(7) +#define ADIHDMI_STATUS_HPD BIT(6) +#define ADIHDMI_STATUS_MONITOR_SENSE BIT(5) +#define ADIHDMI_STATUS_I2S_32BIT_MODE BIT(3) + +#define ADIHDMI_PACKET_ENABLE_N_CTS BIT(8+6) +#define ADIHDMI_PACKET_ENABLE_AUDIO_SAMPLE BIT(8+5) +#define ADIHDMI_PACKET_ENABLE_AVI_INFOFRAME BIT(8+4) +#define ADIHDMI_PACKET_ENABLE_AUDIO_INFOFRAME BIT(8+3) +#define ADIHDMI_PACKET_ENABLE_GC BIT(7) +#define ADIHDMI_PACKET_ENABLE_SPD BIT(6) +#define ADIHDMI_PACKET_ENABLE_MPEG BIT(5) +#define ADIHDMI_PACKET_ENABLE_ACP BIT(4) +#define ADIHDMI_PACKET_ENABLE_ISRC BIT(3) +#define ADIHDMI_PACKET_ENABLE_GM BIT(2) +#define ADIHDMI_PACKET_ENABLE_SPARE2 BIT(1) +#define ADIHDMI_PACKET_ENABLE_SPARE1 BIT(0) + +#define ADIHDMI_REG_POWER2_HDP_SRC_MASK 0xc0 +#define ADIHDMI_REG_POWER2_HDP_SRC_BOTH 0x00 +#define ADIHDMI_REG_POWER2_HDP_SRC_HDP 0x40 +#define ADIHDMI_REG_POWER2_HDP_SRC_CEC 0x80 +#define ADIHDMI_REG_POWER2_HDP_SRC_NONE 0xc0 +#define ADIHDMI_REG_POWER2_TDMS_ENABLE BIT(4) +#define ADIHDMI_REG_POWER2_GATE_INPUT_CLK BIT(0) + +#define ADIHDMI_LOW_REFRESH_RATE_NONE 0x0 +#define ADIHDMI_LOW_REFRESH_RATE_24HZ 0x1 +#define ADIHDMI_LOW_REFRESH_RATE_25HZ 0x2 +#define ADIHDMI_LOW_REFRESH_RATE_30HZ 0x3 + +#define ADIHDMI_AUDIO_CFG3_LEN_MASK 0x0f +#define ADIHDMI_I2C_FREQ_ID_CFG_RATE_MASK 0xf0 + +#define ADIHDMI_AUDIO_SOURCE_I2S 0 +#define ADIHDMI_AUDIO_SOURCE_SPDIF 1 + +#define ADIHDMI_I2S_FORMAT_I2S 0 +#define ADIHDMI_I2S_FORMAT_RIGHT_J 1 +#define ADIHDMI_I2S_FORMAT_LEFT_J 2 + +#define ADIHDMI_PACKET(p, x) ((p) * 0x20 + (x)) +#define ADIHDMI_PACKET_SDP(x) ADIHDMI_PACKET(0, x) +#define ADIHDMI_PACKET_MPEG(x) ADIHDMI_PACKET(1, x) +#define ADIHDMI_PACKET_ACP(x) ADIHDMI_PACKET(2, x) +#define ADIHDMI_PACKET_ISRC1(x) ADIHDMI_PACKET(3, x) +#define ADIHDMI_PACKET_ISRC2(x) ADIHDMI_PACKET(4, x) +#define ADIHDMI_PACKET_GM(x) ADIHDMI_PACKET(5, x) +#define ADIHDMI_PACKET_SPARE(x) ADIHDMI_PACKET(6, x) + +enum adihdmi_input_clock { + ADIHDMI_INPUT_CLOCK_1X, + ADIHDMI_INPUT_CLOCK_2X, + ADIHDMI_INPUT_CLOCK_DDR, +}; + +enum adihdmi_input_justification { + ADIHDMI_INPUT_JUSTIFICATION_EVENLY = 0, + ADIHDMI_INPUT_JUSTIFICATION_RIGHT = 1, + ADIHDMI_INPUT_JUSTIFICATION_LEFT = 2, +}; + +enum adihdmi_input_sync_pulse { + ADIHDMI_INPUT_SYNC_PULSE_DE = 0, + ADIHDMI_INPUT_SYNC_PULSE_HSYNC = 1, + ADIHDMI_INPUT_SYNC_PULSE_VSYNC = 2, + ADIHDMI_INPUT_SYNC_PULSE_NONE = 3, +}; + +/** + * enum adihdmi_sync_polarity - Polarity for the input sync signals + * @ADIHDMI_SYNC_POLARITY_PASSTHROUGH: Sync polarity matches that of + * the currently configured mode. + * @ADIHDMI_SYNC_POLARITY_LOW: Sync polarity is low + * @ADIHDMI_SYNC_POLARITY_HIGH: Sync polarity is high + * + * If the polarity is set to either LOW or HIGH the driver will configure the + * ADIHDMI to internally invert the sync signal if required to match the sync + * polarity setting for the currently selected output mode. + * + * If the polarity is set to PASSTHROUGH, the ADIHDMI will route the signal + * unchanged. This is used when the upstream graphics core already generates + * the sync signals with the correct polarity. + */ +enum adihdmi_sync_polarity { + ADIHDMI_SYNC_POLARITY_PASSTHROUGH, + ADIHDMI_SYNC_POLARITY_LOW, + ADIHDMI_SYNC_POLARITY_HIGH, +}; + +/** + * struct adihdmi_link_config - Describes adihdmi hardware configuration + * @input_color_depth: Number of bits per color component (8, 10 or 12) + * @input_colorspace: The input colorspace (RGB, YUV444, YUV422) + * @input_clock: The input video clock style (1x, 2x, DDR) + * @input_style: The input component arrangement variant + * @input_justification: Video input format bit justification + * @clock_delay: Clock delay for the input clock (in ps) + * @embedded_sync: Video input uses BT.656-style embedded sync + * @sync_pulse: Select the sync pulse + * @vsync_polarity: vsync input signal configuration + * @hsync_polarity: hsync input signal configuration + */ +struct adihdmi_link_config { + unsigned int input_color_depth; + enum hdmi_colorspace input_colorspace; + enum adihdmi_input_clock input_clock; + unsigned int input_style; + enum adihdmi_input_justification input_justification; + + int clock_delay; + + bool embedded_sync; + enum adihdmi_input_sync_pulse sync_pulse; + enum adihdmi_sync_polarity vsync_polarity; + enum adihdmi_sync_polarity hsync_polarity; +}; + +/** + * enum adihdmi_csc_scaling - Scaling factor for the ADIHDMI CSC + * @ADIHDMI_CSC_SCALING_1: CSC results are not scaled + * @ADIHDMI_CSC_SCALING_2: CSC results are scaled by a factor of two + * @ADIHDMI_CSC_SCALING_4: CSC results are scalled by a factor of four + */ +enum adihdmi_csc_scaling { + ADIHDMI_CSC_SCALING_1 = 0, + ADIHDMI_CSC_SCALING_2 = 1, + ADIHDMI_CSC_SCALING_4 = 2, +}; + +/** + * struct adihdmi_video_config - Describes adihdmi hardware configuration + * @csc_enable: Whether to enable color space conversion + * @csc_scaling_factor: Color space conversion scaling factor + * @csc_coefficents: Color space conversion coefficents + * @hdmi_mode: Whether to use HDMI or DVI output mode + * @avi_infoframe: HDMI infoframe + */ +struct adihdmi_video_config { + bool csc_enable; + enum adihdmi_csc_scaling csc_scaling_factor; + const uint16_t *csc_coefficents; + + bool hdmi_mode; + struct hdmi_avi_infoframe avi_infoframe; +}; + +#endif /* __DRM_I2C_ADIHDMI_H__ */ diff --git b/drivers/gpu/drm/i2c/adihdmi_drv.c b/drivers/gpu/drm/i2c/adihdmi_drv.c new file mode 100644 index 000000000..679222463 --- /dev/null +++ b/drivers/gpu/drm/i2c/adihdmi_drv.c @@ -0,0 +1,1268 @@ +/* + * Analog Devices ADIHDMI HDMI transmitter driver + * + * Copyright 2012 Analog Devices Inc. + * Copyright 2015 Konsulko Group + * + * Licensed under the GPL-2. + */ + +#include +#include +#include +#include +#include +#include +#include + +#include +#include +#include +#include +#include + +#include "adihdmi.h" + +#define ADIHDMI_INFOFRAME_PACKETS (0x7900) + +struct adihdmi { + struct i2c_client *i2c_main; + struct i2c_client *i2c_edid; + + struct regmap *regmap; + struct regmap *packet_memory_regmap; + enum drm_connector_status status; + bool powered; + + unsigned int f_tmds; + + unsigned int current_edid_segment; + uint8_t edid_buf[256]; + bool edid_read; + + wait_queue_head_t wq; + struct drm_encoder *encoder; + + bool embedded_sync; + enum adihdmi_sync_polarity vsync_polarity; + enum adihdmi_sync_polarity hsync_polarity; + bool rgb; + + struct edid *edid; + + struct gpio_desc *gpio_pd; +}; + +struct adihdmi2 { + struct adihdmi base; + struct drm_encoder encoder; + struct drm_connector connector; +}; + +/* ADI recommended values for proper operation. */ +static const struct reg_sequence adihdmi_fixed_registers[] = { + { 0x98, 0x03 }, + { 0x9a, 0xe0 }, + { 0x9c, 0x30 }, + { 0x9d, 0x61 }, + { 0xa2, 0xa4 }, + { 0xa3, 0xa4 }, + { 0xe0, 0xd0 }, + { 0xf9, 0x00 }, + { 0x55, 0x02 }, +}; + +/* ----------------------------------------------------------------------------- + * Register access + */ + +static const uint8_t adihdmi_register_defaults[] = { + 0x12, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, /* 00 */ + 0x00, 0x00, 0x01, 0x0e, 0xbc, 0x18, 0x01, 0x13, + 0x25, 0x37, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, /* 10 */ + 0x46, 0x62, 0x04, 0xa8, 0x00, 0x00, 0x1c, 0x84, + 0x1c, 0xbf, 0x04, 0xa8, 0x1e, 0x70, 0x02, 0x1e, /* 20 */ + 0x00, 0x00, 0x04, 0xa8, 0x08, 0x12, 0x1b, 0xac, + 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, /* 30 */ + 0x00, 0x00, 0x00, 0x80, 0x00, 0x00, 0x00, 0xb0, + 0x00, 0x50, 0x90, 0x7e, 0x79, 0x70, 0x00, 0x00, /* 40 */ + 0x00, 0xa8, 0x80, 0x00, 0x00, 0x00, 0x00, 0x00, + 0x00, 0x00, 0x02, 0x0d, 0x00, 0x00, 0x00, 0x00, /* 50 */ + 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, + 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, /* 60 */ + 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, + 0x01, 0x0a, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, /* 70 */ + 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, + 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, /* 80 */ + 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, + 0x00, 0x00, 0x00, 0x00, 0xc0, 0x00, 0x00, 0x00, /* 90 */ + 0x0b, 0x02, 0x00, 0x18, 0x5a, 0x60, 0x00, 0x00, + 0x00, 0x00, 0x80, 0x80, 0x08, 0x04, 0x00, 0x00, /* a0 */ + 0x00, 0x00, 0x00, 0x40, 0x00, 0x00, 0x40, 0x14, + 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, /* b0 */ + 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, + 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, /* c0 */ + 0x00, 0x03, 0x00, 0x00, 0x02, 0x00, 0x01, 0x04, + 0x30, 0xff, 0x80, 0x80, 0x80, 0x00, 0x00, 0x00, /* d0 */ + 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x10, 0x01, + 0x80, 0x75, 0x00, 0x00, 0x60, 0x00, 0x00, 0x00, /* e0 */ + 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, + 0x00, 0x00, 0x00, 0x00, 0x00, 0x75, 0x11, 0x00, /* f0 */ + 0x00, 0x7c, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, +}; + +static bool adihdmi_register_volatile(struct device *dev, unsigned int reg) +{ + switch (reg) { + case ADIHDMI_REG_CHIP_REVISION: + case ADIHDMI_REG_SPDIF_FREQ: + case ADIHDMI_REG_CTS_AUTOMATIC1: + case ADIHDMI_REG_CTS_AUTOMATIC2: + case ADIHDMI_REG_VIC_DETECTED: + case ADIHDMI_REG_VIC_SEND: + case ADIHDMI_REG_AUX_VIC_DETECTED: + case ADIHDMI_REG_STATUS: + case ADIHDMI_REG_GC(1): + case ADIHDMI_REG_INT(0): + case ADIHDMI_REG_INT(1): + case ADIHDMI_REG_PLL_STATUS: + case ADIHDMI_REG_AN(0): + case ADIHDMI_REG_AN(1): + case ADIHDMI_REG_AN(2): + case ADIHDMI_REG_AN(3): + case ADIHDMI_REG_AN(4): + case ADIHDMI_REG_AN(5): + case ADIHDMI_REG_AN(6): + case ADIHDMI_REG_AN(7): + case ADIHDMI_REG_HDCP_STATUS: + case ADIHDMI_REG_BCAPS: + case ADIHDMI_REG_BKSV(0): + case ADIHDMI_REG_BKSV(1): + case ADIHDMI_REG_BKSV(2): + case ADIHDMI_REG_BKSV(3): + case ADIHDMI_REG_BKSV(4): + case ADIHDMI_REG_DDC_STATUS: + case ADIHDMI_REG_BSTATUS(0): + case ADIHDMI_REG_BSTATUS(1): + case ADIHDMI_REG_CHIP_ID_HIGH: + case ADIHDMI_REG_CHIP_ID_LOW: + return true; + } + + return false; +} + +static const struct regmap_config adihdmi_regmap_config = { + .reg_bits = 8, + .val_bits = 8, + + .max_register = 0xff, + .cache_type = REGCACHE_RBTREE, + .reg_defaults_raw = adihdmi_register_defaults, + .num_reg_defaults_raw = ARRAY_SIZE(adihdmi_register_defaults), + + .volatile_reg = adihdmi_register_volatile, +}; + +/* ----------------------------------------------------------------------------- + * Hardware configuration + */ + + static void adihdmi_audio_setup(struct adihdmi * adihdmi) +{ + /* Select I2S. */ + regmap_write(adihdmi->regmap, ADIHDMI_REG_AUDIO_SOURCE, 0x01); + regmap_write(adihdmi->regmap, ADIHDMI_REG_I2S_CONFIG, 0x84); + + /* Setup clocks for 48KHz. */ + regmap_write(adihdmi->regmap, ADIHDMI_REG_N0, 0x00); + regmap_write(adihdmi->regmap, ADIHDMI_REG_N1, 0x18); + regmap_write(adihdmi->regmap, ADIHDMI_REG_N2, 0x00); + regmap_update_bits(adihdmi->regmap, ADIHDMI_REG_I2C_FREQ_ID_CFG, 0xF0, 0x20); + + /* Set audio word length to 24 bits. */ + regmap_update_bits(adihdmi->regmap, ADIHDMI_REG_AUDIO_CFG3, 0x0F, 0x0B); + + /* Update audio infoframe. */ + regmap_update_bits(adihdmi->regmap, ADIHDMI_REG_INFOFRAME_UPDATE, 0x20, 0x20); + regmap_update_bits(adihdmi->regmap, ADIHDMI_REG_AUDIO_INFOFRAME(0), 0x07, 0x01); + regmap_update_bits(adihdmi->regmap, ADIHDMI_REG_AUDIO_INFOFRAME(3), 0x1F, 0x00); + regmap_update_bits(adihdmi->regmap, ADIHDMI_REG_INFOFRAME_UPDATE, 0x20, 0x00); +} + +static void adihdmi_set_colormap(struct adihdmi *adihdmi, bool enable, + const uint16_t *coeff, + unsigned int scaling_factor) +{ + unsigned int i; + + regmap_update_bits(adihdmi->regmap, ADIHDMI_REG_CSC_UPPER(1), + ADIHDMI_CSC_UPDATE_MODE, ADIHDMI_CSC_UPDATE_MODE); + + if (enable) { + for (i = 0; i < 12; ++i) { + regmap_update_bits(adihdmi->regmap, + ADIHDMI_REG_CSC_UPPER(i), + 0x1f, coeff[i] >> 8); + regmap_write(adihdmi->regmap, + ADIHDMI_REG_CSC_LOWER(i), + coeff[i] & 0xff); + } + } + + if (enable) + regmap_update_bits(adihdmi->regmap, ADIHDMI_REG_CSC_UPPER(0), + 0xe0, 0x80 | (scaling_factor << 5)); + else + regmap_update_bits(adihdmi->regmap, ADIHDMI_REG_CSC_UPPER(0), + 0x80, 0x00); + + regmap_update_bits(adihdmi->regmap, ADIHDMI_REG_CSC_UPPER(1), + ADIHDMI_CSC_UPDATE_MODE, 0); +} + +static int adihdmi_packet_enable(struct adihdmi *adihdmi, unsigned int packet) +{ + if (packet & 0xff) + regmap_update_bits(adihdmi->regmap, ADIHDMI_REG_PACKET_ENABLE0, + packet, 0xff); + + if (packet & 0xff00) { + packet >>= 8; + regmap_update_bits(adihdmi->regmap, ADIHDMI_REG_PACKET_ENABLE1, + packet, 0xff); + } + + return 0; +} + +static int adihdmi_packet_disable(struct adihdmi *adihdmi, unsigned int packet) +{ + if (packet & 0xff) + regmap_update_bits(adihdmi->regmap, ADIHDMI_REG_PACKET_ENABLE0, + packet, 0x00); + + if (packet & 0xff00) { + packet >>= 8; + regmap_update_bits(adihdmi->regmap, ADIHDMI_REG_PACKET_ENABLE1, + packet, 0x00); + } + + return 0; +} + +/* Coefficients for adihdmi color space conversion */ +static const uint16_t adihdmi_csc_ycbcr_to_rgb[] = { + 0x0734, 0x04ad, 0x0000, 0x1c1b, + 0x1ddc, 0x04ad, 0x1f24, 0x0135, + 0x0000, 0x04ad, 0x087c, 0x1b77, +}; + +static void adihdmi_set_config_csc(struct adihdmi *adihdmi, + struct drm_connector *connector, + bool rgb) +{ + struct adihdmi_video_config config; + bool output_format_422, output_format_ycbcr; + unsigned int mode; + uint8_t infoframe[17]; + + if (adihdmi->edid) + config.hdmi_mode = drm_detect_hdmi_monitor(adihdmi->edid); + else + config.hdmi_mode = false; + + hdmi_avi_infoframe_init(&config.avi_infoframe); + + config.avi_infoframe.scan_mode = HDMI_SCAN_MODE_UNDERSCAN; + + if (rgb) { + config.csc_enable = false; + config.avi_infoframe.colorspace = HDMI_COLORSPACE_RGB; + } else { + config.csc_scaling_factor = ADIHDMI_CSC_SCALING_4; + config.csc_coefficents = adihdmi_csc_ycbcr_to_rgb; + + if ((connector->display_info.color_formats & + DRM_COLOR_FORMAT_YCRCB422) && + config.hdmi_mode) { + config.csc_enable = false; + config.avi_infoframe.colorspace = + HDMI_COLORSPACE_YUV422; + } else { + config.csc_enable = true; + config.avi_infoframe.colorspace = HDMI_COLORSPACE_RGB; + } + } + + if (config.hdmi_mode) { + mode = ADIHDMI_HDMI_CFG_MODE_HDMI; + + switch (config.avi_infoframe.colorspace) { + case HDMI_COLORSPACE_YUV444: + output_format_422 = false; + output_format_ycbcr = true; + break; + case HDMI_COLORSPACE_YUV422: + output_format_422 = true; + output_format_ycbcr = true; + break; + default: + output_format_422 = false; + output_format_ycbcr = false; + break; + } + } else { + mode = ADIHDMI_HDMI_CFG_MODE_DVI; + output_format_422 = false; + output_format_ycbcr = false; + } + + adihdmi_packet_disable(adihdmi, ADIHDMI_INFOFRAME_PACKETS); + + adihdmi_set_colormap(adihdmi, config.csc_enable, + config.csc_coefficents, + config.csc_scaling_factor); + + regmap_update_bits(adihdmi->regmap, ADIHDMI_REG_VIDEO_INPUT_CFG1, 0x81, + (output_format_422 << 7) | output_format_ycbcr); + + regmap_update_bits(adihdmi->regmap, ADIHDMI_REG_HDCP_HDMI_CFG, + ADIHDMI_HDMI_CFG_MODE_MASK, mode); + + hdmi_avi_infoframe_pack(&config.avi_infoframe, infoframe, + sizeof(infoframe)); + + /* The AVI infoframe id is not configurable */ + regmap_bulk_write(adihdmi->regmap, ADIHDMI_REG_AVI_INFOFRAME_VERSION, + infoframe + 1, sizeof(infoframe) - 1); + + adihdmi_packet_enable(adihdmi, ADIHDMI_INFOFRAME_PACKETS); +} + +static void adihdmi_set_link_config(struct adihdmi *adihdmi, + const struct adihdmi_link_config *config) +{ + /* + * The input style values documented in the datasheet don't match the + * hardware register field values :-( + */ + static const unsigned int input_styles[4] = { 0, 2, 1, 3 }; + + unsigned int clock_delay; + unsigned int color_depth; + unsigned int input_id; + + clock_delay = (config->clock_delay + 1200) / 400; + color_depth = config->input_color_depth == 8 ? 3 + : (config->input_color_depth == 10 ? 1 : 2); + + /* TODO Support input ID 6 */ + if (config->input_colorspace != HDMI_COLORSPACE_YUV422) + input_id = config->input_clock == ADIHDMI_INPUT_CLOCK_DDR + ? 5 : 0; + else if (config->input_clock == ADIHDMI_INPUT_CLOCK_DDR) + input_id = config->embedded_sync ? 8 : 7; + else if (config->input_clock == ADIHDMI_INPUT_CLOCK_2X) + input_id = config->embedded_sync ? 4 : 3; + else + input_id = config->embedded_sync ? 2 : 1; + + regmap_update_bits(adihdmi->regmap, ADIHDMI_REG_I2C_FREQ_ID_CFG, 0xf, + input_id); + regmap_update_bits(adihdmi->regmap, ADIHDMI_REG_VIDEO_INPUT_CFG1, 0x7e, + (color_depth << 4) | + (input_styles[config->input_style] << 2)); + regmap_write(adihdmi->regmap, ADIHDMI_REG_VIDEO_INPUT_CFG2, + config->input_justification << 3); + regmap_write(adihdmi->regmap, ADIHDMI_REG_TIMING_GEN_SEQ, + config->sync_pulse << 2); + + regmap_write(adihdmi->regmap, 0xba, clock_delay << 5); + + adihdmi->embedded_sync = config->embedded_sync; + adihdmi->hsync_polarity = config->hsync_polarity; + adihdmi->vsync_polarity = config->vsync_polarity; + adihdmi->rgb = config->input_colorspace == HDMI_COLORSPACE_RGB; +} + +static void adihdmi_power_on(struct adihdmi *adihdmi) +{ + adihdmi->current_edid_segment = -1; + + regmap_write(adihdmi->regmap, ADIHDMI_REG_INT(0), + ADIHDMI_INT0_EDID_READY); + regmap_write(adihdmi->regmap, ADIHDMI_REG_INT(1), + ADIHDMI_INT1_DDC_ERROR); + regmap_update_bits(adihdmi->regmap, ADIHDMI_REG_POWER, + ADIHDMI_POWER_POWER_DOWN, 0); + + /* + * Per spec it is allowed to pulse the HDP signal to indicate that the + * EDID information has changed. Some monitors do this when they wakeup + * from standby or are enabled. When the HDP goes low the adihdmi is + * reset and the outputs are disabled which might cause the monitor to + * go to standby again. To avoid this we ignore the HDP pin for the + * first few seconds after enabling the output. + */ + regmap_update_bits(adihdmi->regmap, ADIHDMI_REG_POWER2, + ADIHDMI_REG_POWER2_HDP_SRC_MASK, + ADIHDMI_REG_POWER2_HDP_SRC_NONE); + + /* + * Most of the registers are reset during power down or when HPD is low. + */ + regcache_sync(adihdmi->regmap); + + adihdmi->powered = true; +} + +static void adihdmi_power_off(struct adihdmi *adihdmi) +{ + /* TODO: setup additional power down modes */ + regmap_update_bits(adihdmi->regmap, ADIHDMI_REG_POWER, + ADIHDMI_POWER_POWER_DOWN, + ADIHDMI_POWER_POWER_DOWN); + regcache_mark_dirty(adihdmi->regmap); + + adihdmi->powered = false; +} + +/* ----------------------------------------------------------------------------- + * Interrupt and hotplug detection + */ + +static bool adihdmi_hpd(struct adihdmi *adihdmi) +{ + unsigned int irq0; + int ret; + + ret = regmap_read(adihdmi->regmap, ADIHDMI_REG_INT(0), &irq0); + if (ret < 0) + return false; + + if (irq0 & ADIHDMI_INT0_HDP) { + regmap_write(adihdmi->regmap, ADIHDMI_REG_INT(0), + ADIHDMI_INT0_HDP); + return true; + } + + return false; +} + +static int adihdmi_irq_process(struct adihdmi *adihdmi) +{ + unsigned int irq0, irq1; + int ret; + + ret = regmap_read(adihdmi->regmap, ADIHDMI_REG_INT(0), &irq0); + if (ret < 0) + return ret; + + ret = regmap_read(adihdmi->regmap, ADIHDMI_REG_INT(1), &irq1); + if (ret < 0) + return ret; + + regmap_write(adihdmi->regmap, ADIHDMI_REG_INT(0), irq0); + regmap_write(adihdmi->regmap, ADIHDMI_REG_INT(1), irq1); + + if (irq0 & ADIHDMI_INT0_HDP) + drm_helper_hpd_irq_event(adihdmi->encoder->dev); + + if (irq0 & ADIHDMI_INT0_EDID_READY || irq1 & ADIHDMI_INT1_DDC_ERROR) { + adihdmi->edid_read = true; + + if (adihdmi->i2c_main->irq) + wake_up_all(&adihdmi->wq); + } + + return 0; +} + +static irqreturn_t adihdmi_irq_handler(int irq, void *devid) +{ + struct adihdmi *adihdmi = devid; + int ret; + + ret = adihdmi_irq_process(adihdmi); + return ret < 0 ? IRQ_NONE : IRQ_HANDLED; +} + +/* ----------------------------------------------------------------------------- + * EDID retrieval + */ + +static int adihdmi_wait_for_edid(struct adihdmi *adihdmi, int timeout) +{ + int ret; + + if (adihdmi->i2c_main->irq) { + ret = wait_event_interruptible_timeout(adihdmi->wq, + adihdmi->edid_read, msecs_to_jiffies(timeout)); + } else { + for (; timeout > 0; timeout -= 25) { + ret = adihdmi_irq_process(adihdmi); + if (ret < 0) + break; + + if (adihdmi->edid_read) + break; + + msleep(25); + } + } + + return adihdmi->edid_read ? 0 : -EIO; +} + +static int adihdmi_get_edid_block(void *data, u8 *buf, unsigned int block, + size_t len) +{ + struct adihdmi *adihdmi = data; + struct i2c_msg xfer[2]; + uint8_t offset; + unsigned int i; + int ret; + + if (len > 128) + return -EINVAL; + + if (adihdmi->current_edid_segment != block / 2) { + unsigned int status; + + ret = regmap_read(adihdmi->regmap, ADIHDMI_REG_DDC_STATUS, + &status); + if (ret < 0) + return ret; + + if (status != 2) { + adihdmi->edid_read = false; + regmap_write(adihdmi->regmap, ADIHDMI_REG_EDID_SEGMENT, + block); + ret = adihdmi_wait_for_edid(adihdmi, 200); + if (ret < 0) + return ret; + } + + /* Break this apart, hopefully more I2C controllers will + * support 64 byte transfers than 256 byte transfers + */ + + xfer[0].addr = adihdmi->i2c_edid->addr; + xfer[0].flags = 0; + xfer[0].len = 1; + xfer[0].buf = &offset; + xfer[1].addr = adihdmi->i2c_edid->addr; + xfer[1].flags = I2C_M_RD; + xfer[1].len = 64; + xfer[1].buf = adihdmi->edid_buf; + + offset = 0; + + for (i = 0; i < 4; ++i) { + ret = i2c_transfer(adihdmi->i2c_edid->adapter, xfer, + ARRAY_SIZE(xfer)); + if (ret < 0) + return ret; + else if (ret != 2) + return -EIO; + + xfer[1].buf += 64; + offset += 64; + } + + adihdmi->current_edid_segment = block / 2; + } + + if (block % 2 == 0) + memcpy(buf, adihdmi->edid_buf, len); + else + memcpy(buf, adihdmi->edid_buf + 128, len); + + return 0; +} + +static int adihdmi_mode_valid(struct drm_display_mode *mode) +{ + if (mode->clock > 165000) + return MODE_CLOCK_HIGH; + + return MODE_OK; +} + +/* ----------------------------------------------------------------------------- + * DT and private structure operations + */ + +#define conn_to_adihdmi2(x) \ + container_of(x, struct adihdmi2, connector); + +#define enc_to_adihdmi2(x) \ + container_of(x, struct adihdmi2, encoder); + +#define enc_to_adihdmi(x) \ + (&(container_of(x, struct adihdmi2, encoder)->base)) + +static int adihdmi_parse_dt(struct device_node *np, + struct adihdmi_link_config *config) +{ + memset(config, 0, sizeof(*config)); + + config->input_color_depth = 8; + + config->input_colorspace = HDMI_COLORSPACE_RGB; + //config->input_colorspace = HDMI_COLORSPACE_YUV422; + //config->input_colorspace = HDMI_COLORSPACE_YUV444; + + config->input_clock = ADIHDMI_INPUT_CLOCK_1X; + //config->input_clock = ADIHDMI_INPUT_CLOCK_2X; + //config->input_clock = ADIHDMI_INPUT_CLOCK_DDR; + + if (config->input_colorspace == HDMI_COLORSPACE_YUV422 || + config->input_clock != ADIHDMI_INPUT_CLOCK_1X) { + + config->input_style = 1; + //config->input_justification = ADIHDMI_INPUT_JUSTIFICATION_LEFT; + config->input_justification = ADIHDMI_INPUT_JUSTIFICATION_EVENLY; + //config->input_justification = ADIHDMI_INPUT_JUSTIFICATION_RIGHT; + + } else { + config->input_style = 1; + config->input_justification = ADIHDMI_INPUT_JUSTIFICATION_LEFT; + } + + config->clock_delay = 0; + config->embedded_sync = 0; + + /* Hardcode the sync pulse configurations for now. */ + config->sync_pulse = ADIHDMI_INPUT_SYNC_PULSE_NONE; + config->vsync_polarity = ADIHDMI_SYNC_POLARITY_PASSTHROUGH; + config->hsync_polarity = ADIHDMI_SYNC_POLARITY_PASSTHROUGH; + + return 0; +} + +static const int edid_i2c_addr = 0x7e; +static const int packet_i2c_addr = 0x70; +static const int cec_i2c_addr = 0x78; + +static int adihdmi_create(struct i2c_client *i2c, struct adihdmi *adihdmi) +{ + struct adihdmi_link_config link_config; + struct device *dev = &i2c->dev; + unsigned int val; + int ret; + + adihdmi->powered = false; + adihdmi->status = connector_status_disconnected; + + ret = adihdmi_parse_dt(NULL, &link_config); + if (ret) + { + pr_err("%s - %d - Bad parse\n", __FUNCTION__, __LINE__); + return -EINVAL; + } + + /* + * The power down GPIO is optional. If present, toggle it from active to + * inactive to wake up the encoder. + */ + adihdmi->gpio_pd = devm_gpiod_get_optional(dev, "pd", GPIOD_OUT_HIGH); + if (IS_ERR(adihdmi->gpio_pd)) + { + pr_err("%s - %d - Bad PD GPIO\n", __FUNCTION__, __LINE__); + return PTR_ERR(adihdmi->gpio_pd); + } + + if (adihdmi->gpio_pd) { + mdelay(5); + gpiod_set_value_cansleep(adihdmi->gpio_pd, 0); + } + + adihdmi->regmap = devm_regmap_init_i2c(i2c, &adihdmi_regmap_config); + if (IS_ERR(adihdmi->regmap)) + { + pr_err("%s - %d - Bad reg map init\n", __FUNCTION__, __LINE__); + return PTR_ERR(adihdmi->regmap); + } + + ret = regmap_read(adihdmi->regmap, ADIHDMI_REG_CHIP_REVISION, &val); + if (ret) + { + pr_err("%s - %d - Bad reg map read\n", __FUNCTION__, __LINE__); + return ret; + } + dev_dbg(dev, "Rev. %d\n", val); + + ret = regmap_register_patch(adihdmi->regmap, adihdmi_fixed_registers, + ARRAY_SIZE(adihdmi_fixed_registers)); + if (ret) + { + pr_err("%s - %d - Bad reg map patch\n", __FUNCTION__, __LINE__); + return ret; + } + + regmap_write(adihdmi->regmap, ADIHDMI_REG_EDID_I2C_ADDR, edid_i2c_addr); + regmap_write(adihdmi->regmap, ADIHDMI_REG_PACKET_I2C_ADDR, + packet_i2c_addr); + regmap_write(adihdmi->regmap, ADIHDMI_REG_CEC_I2C_ADDR, cec_i2c_addr); + adihdmi_packet_disable(adihdmi, 0xffff); + + adihdmi->i2c_main = i2c; + adihdmi->i2c_edid = i2c_new_dummy(i2c->adapter, edid_i2c_addr >> 1); + if (!adihdmi->i2c_edid) + { + pr_err("%s - %d - No mem for EDID\n", __FUNCTION__, __LINE__); + return -ENOMEM; + } + + if (i2c->irq) { + init_waitqueue_head(&adihdmi->wq); + + ret = devm_request_threaded_irq(dev, i2c->irq, NULL, + adihdmi_irq_handler, + IRQF_ONESHOT, dev_name(dev), + adihdmi); + if (ret) + { + pr_err("%s - %d - Bad IRQ thread request\n", __FUNCTION__, __LINE__); + goto err_i2c_unregister_device; + } + } + + /* CEC is unused for now */ + regmap_write(adihdmi->regmap, ADIHDMI_REG_CEC_CTRL, + ADIHDMI_CEC_CTRL_POWER_DOWN); + + adihdmi_power_off(adihdmi); + + adihdmi_set_link_config(adihdmi, &link_config); + + adihdmi_audio_setup(adihdmi); + + return 0; + +err_i2c_unregister_device: + i2c_unregister_device(adihdmi->i2c_edid); + + return ret; +} + +static void adihdmi_destroy(struct adihdmi *priv) +{ + i2c_unregister_device(priv->i2c_edid); +} + +/* ----------------------------------------------------------------------------- + * Encoder operations + */ + +static int adihdmi_encoder_get_modes(struct adihdmi *adihdmi, + struct drm_connector *connector) +{ + struct edid *edid; + unsigned int count; + + /* Reading the EDID only works if the device is powered */ + if (!adihdmi->powered) { + regmap_write(adihdmi->regmap, ADIHDMI_REG_INT(0), + ADIHDMI_INT0_EDID_READY); + regmap_write(adihdmi->regmap, ADIHDMI_REG_INT(1), + ADIHDMI_INT1_DDC_ERROR); + regmap_update_bits(adihdmi->regmap, ADIHDMI_REG_POWER, + ADIHDMI_POWER_POWER_DOWN, 0); + adihdmi->current_edid_segment = -1; + } + + edid = drm_do_get_edid(connector, adihdmi_get_edid_block, adihdmi); + + if (!adihdmi->powered) + regmap_update_bits(adihdmi->regmap, ADIHDMI_REG_POWER, + ADIHDMI_POWER_POWER_DOWN, + ADIHDMI_POWER_POWER_DOWN); + + kfree(adihdmi->edid); + adihdmi->edid = edid; + if (!edid) + { + pr_err("%s - %d - No EDID\n", __FUNCTION__, __LINE__); + return 0; + } + + drm_mode_connector_update_edid_property(connector, edid); + count = drm_add_edid_modes(connector, edid); + + adihdmi_set_config_csc(adihdmi, connector, adihdmi->rgb); + + return count; +} + +static void adihdmi_encoder_dpms(struct drm_encoder *encoder, int mode) +{ + struct adihdmi2 *priv2 = enc_to_adihdmi2(encoder); + + if (mode == DRM_MODE_DPMS_ON) + adihdmi_power_on(&priv2->base); + else + adihdmi_power_off(&priv2->base); +} + + static enum drm_connector_status +adihdmi_encoder_detect(struct adihdmi *adihdmi, + struct drm_connector *connector) +{ + enum drm_connector_status status; + unsigned int val; + bool hpd; + int ret; + + ret = regmap_read(adihdmi->regmap, ADIHDMI_REG_STATUS, &val); + if (ret < 0) + { + pr_err("%s - %d - Disconnected\n", __FUNCTION__, __LINE__); + return connector_status_disconnected; + } + + if (val & ADIHDMI_STATUS_HPD) + status = connector_status_connected; + else + status = connector_status_disconnected; + + hpd = adihdmi_hpd(adihdmi); + + /* The chip resets itself when the cable is disconnected, so in case + * there is a pending HPD interrupt and the cable is connected there was + * at least one transition from disconnected to connected and the chip + * has to be reinitialized. */ + if (status == connector_status_connected && hpd && adihdmi->powered) { + regcache_mark_dirty(adihdmi->regmap); + adihdmi_power_on(adihdmi); + adihdmi_encoder_get_modes(adihdmi, connector); + if (adihdmi->status == connector_status_connected) + status = connector_status_disconnected; + } else { + /* Renable HDP sensing */ + regmap_update_bits(adihdmi->regmap, ADIHDMI_REG_POWER2, + ADIHDMI_REG_POWER2_HDP_SRC_MASK, + ADIHDMI_REG_POWER2_HDP_SRC_BOTH); + } + + adihdmi->status = status; + return status; +} + +static bool adihdmi_encoder_mode_fixup(struct drm_encoder *encoder, const struct drm_display_mode *mode, struct drm_display_mode *adjusted_mode) +{ + return true; +} + +static int adihdmi_encoder_mode_valid(struct drm_encoder *encoder, struct drm_display_mode *mode) +{ + return adihdmi_mode_valid(mode); +} + +static void adihdmi_encoder_mode_set(struct drm_encoder *encoder, + struct drm_display_mode *mode, + struct drm_display_mode *adj_mode) +{ + unsigned int low_refresh_rate; + unsigned int hsync_polarity = 0; + unsigned int vsync_polarity = 0; + struct adihdmi *adihdmi = enc_to_adihdmi(encoder); + + if (adihdmi->embedded_sync) { + unsigned int hsync_offset, hsync_len; + unsigned int vsync_offset, vsync_len; + + hsync_offset = adj_mode->crtc_hsync_start - + adj_mode->crtc_hdisplay; + vsync_offset = adj_mode->crtc_vsync_start - + adj_mode->crtc_vdisplay; + hsync_len = adj_mode->crtc_hsync_end - + adj_mode->crtc_hsync_start; + vsync_len = adj_mode->crtc_vsync_end - + adj_mode->crtc_vsync_start; + + /* The hardware vsync generator has a off-by-one bug */ + vsync_offset += 1; + + regmap_write(adihdmi->regmap, ADIHDMI_REG_HSYNC_PLACEMENT_MSB, + ((hsync_offset >> 10) & 0x7) << 5); + regmap_write(adihdmi->regmap, ADIHDMI_REG_SYNC_DECODER(0), + (hsync_offset >> 2) & 0xff); + regmap_write(adihdmi->regmap, ADIHDMI_REG_SYNC_DECODER(1), + ((hsync_offset & 0x3) << 6) | + ((hsync_len >> 4) & 0x3f)); + regmap_write(adihdmi->regmap, ADIHDMI_REG_SYNC_DECODER(2), + ((hsync_len & 0xf) << 4) | + ((vsync_offset >> 6) & 0xf)); + regmap_write(adihdmi->regmap, ADIHDMI_REG_SYNC_DECODER(3), + ((vsync_offset & 0x3f) << 2) | + ((vsync_len >> 8) & 0x3)); + regmap_write(adihdmi->regmap, ADIHDMI_REG_SYNC_DECODER(4), + vsync_len & 0xff); + + hsync_polarity = !(adj_mode->flags & DRM_MODE_FLAG_PHSYNC); + vsync_polarity = !(adj_mode->flags & DRM_MODE_FLAG_PVSYNC); + } else { + enum adihdmi_sync_polarity mode_hsync_polarity; + enum adihdmi_sync_polarity mode_vsync_polarity; + + /** + * If the input signal is always low or always high we want to + * invert or let it passthrough depending on the polarity of the + * current mode. + **/ + if (adj_mode->flags & DRM_MODE_FLAG_NHSYNC) + mode_hsync_polarity = ADIHDMI_SYNC_POLARITY_LOW; + else + mode_hsync_polarity = ADIHDMI_SYNC_POLARITY_HIGH; + + if